GE APPLIANCES 93056860 EWLS 12 Watt Evolve LED Wall Pack Installation Guide

Installation Guide
GEH6060 | 99003213
Evolve™ LED Wallpack

93056860 EWLS 12 Watt Evolve LED Wall Pack

BEFORE YOU BEGIN
Read these instructions and save for future use.

WARNING
RISK OF ELECTRIC SHOCK
Disconnect power before service installation, or maintenance of the product.
RISK OF INJURY OR DAMAGE
Unit will fall if not installed properly. Follow installation instructions.

CAUTION
RISK OF INJURY
The luminaire should be mounted so that prolonged staring into the luminaire at a distance closer than 0.50m is not expected.

Storage & Handling

|
---|---
Store packaged units in a covered dry area| Check for damage
|
Do not impact| Do not stack

Preparation for Mounting

Battery and test button| Motion sensor| Button photocontrol

Remove battery and test button, motion sensor, or button photocontrol it necessary to mount box.

Junction Box Mounting

Mount to a 3 ½-in. square or 4-in. octagonal recessed outlet box.| Apply gaskets.| Caulk upper edge and sides on rough surfaces.

Fasten to junction box with user supplied screws.

CAUTION
Water-tight conduit connections are required when using the mounting box knockouts

Surface Conduit

Knock out conduit entries as needed.| Attach to wall (follow Step 4 below).| Fasten/seal conduit to box.

Surface Mount

Locate and drill holes in wall surface of| Install user-supplied anchors.| Apply gaskets.

Caulk upper edge and sides on rough surfaces.| Fasten plate or box to wall with user supplied screws.

WARNING
RISK OF INJURY OR DAMAGE
Select user-supplied wall anchors and anchor fasteners suitable for the wall construction and the fixture’s mounting hole diameters. Ensure a minimum per- anchor pull-out- strength of 10 times (10X) the fixture weight and install per the manufacturer’s instructions.

Wiring

CAUTION
RISK OF SHOCK OR DAMAGE
Follow applicable national and localelectrical codes.
RISK OF DAMAGE
Verify supply voltage and wire insulation temperature rating match nameplate requirements.

Reinstall battery and test button, motion sensor, or button photocontrol if previously removed.| Connect supply leads to fixture.

(Standard No Sensors) Connect supply leads to fixture and backplate ground leads.| (Button Photocontrol) Connect supply leads to fixture, Button PE, and backplate ground leads.

(EMBB) Connect supply leads to fixture, EMBB, and chassis ground leads.| (Internal Motion Sensor) Connect supply leads to fixture, sensor, and backplate ground leads.

WARNING
RISK OF FAILURE.
An unswitched AC power source of 100VAC to 277VAC is required for proper EMBB charging and operation. An Illuminated LED indicator light indicates AC power is applied.

Controls

Verify if unit has a programmable occupancy sensor.| Refer to FSIR-100 datasheet for programable settings.| Aim FSIR-100 at fixture and program settings.

Button Up

Fasten housing to box or plate.| For ADA installations, use shorter screws.| Insert plugs to hide screws.

Testing EMBB

Push button to test operation.| Note flashing light, see Table 1 for codes.

Table 1: Test Switch Indicator Status

connection.
Flashing Red| 1s / 1s| Replace battery.
Flashing Green| 2s / 2s| Self-Diagnostic test underway.
Fast Flashing Red| 0.1s / 0.1s| Abnormal driver performance, replace driver.
Very Slow Flashing Red| 1s / 7s| Over temperature.
Very Slow Flashing Red| 4s / 4s| LED output load is Short/Over Current/Over Voltage/Open Circuit in EM Mode.

Cleaning

Use mild soap/detergent.| Rinse with cool low pressure water.| Wipe dry with clean soft cloth.

CAUTION
RISK OF DAMAGE.
Do not use soap/detergent containing aromatic hydrocarbons.

Specifications

Luminaire| Weight| Dimensions| IP Rating| Mounting Height| Operating Temp.
---|---|---|---|---|---
EWLS| 7.4 lbs. (3.4 kg)| 8.3 x 7.4 x 6.3 in.
(211 x 188 x 160 mm)| Optical and all Electrical
Components IP66| 8-25 ft (2.4-7.6 m)| -40° to 50°C
EWLS (EMBB)| 8.0 lbs. (3.6 kg)
EWLS (347V)| 9.4 lbs. (4.3 kg)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation. This Class [A] RFLD complies with the Canadian standard ICES-005.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

© 2021 Current Lighting Solutions, LLC. All rights reserved. GE and the GE monogram are trademarks of the General Electric Company and are used under license. Information provided is subject to change without notice. All values are design or typical values when measured under laboratory conditions.

www.gecurrent.com
GEH6060 (Rev 05/17/21) 99003213

Documents / Resources

| GE APPLIANCES 93056860 EWLS 12 Watt Evolve LED Wall Pack [pdf] Installation Guide
93056860, EWLS 12 Watt Evolve LED Wall Pack, 93056860 EWLS 12 Watt Evolve LED Wall Pack, 12 Watt Evolve LED Wall Pack, Evolve LED Wall Pack, LED Wall Pack, Wall Pack
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>