GE CYNC LED Smart Light Strip Installation Guide
- October 30, 2023
- GE
Table of Contents
LED
Smart Light Strip
Installation Guide
What’s Included
(Devices each sold separately)
Light Strip Contents
Light Strip + Power Supply
- 16ft Full Color Light Strip
- Power supply with plug
- Reconnector wire
- (6) Mounting clips
- Cleaning wipe
Light Strip Extension Contents
Light Strip Extension
- 8ft Full Color Light Strip
- Extension cable (power supply sold separately)
- Snap connector
- (3) Mounting clips
Mounting clips may vary.
Easy Setup
Set up your Light Strips with three easy steps:
| STEP 1
Connect to the Cync App, powered by Savant.
---|---
| STEP 2
Trim to desired length.
| STEP 3
Prep surface and install.
Set Up in the CYNC App
| STEP 1
Plug in and power on your Light Strip by pressing the On/Off button on the
power supply.
---|---
|
STEP 2
Download the Cync App, powered by Savant, on your smartphone.
| STEP 3
Add your smart lights to the Cync App, then connect to Hey Google or Amazon
Alexa voice assistants (sold separately) in the Cync App.
For set up help, visit cyncsupport.gelighting.com or call 1-844-302-2943
GE and C by GE ore trademarks of General Electric Company. Used under
trademark license.
Amazon, Alexa, and all related logos are trademarks of
Amozon.com, Inc. or its affiliates.
Google and other related marks and logos are trademarks of Google LLC.
Measure & Trim to Size
(If desired)
STEP 1
Measure where you’re planning to install your lights. If your space requires
Light Strip Extensions, make sure to attach them before trimming your strips.
STEP 2
With your Light Strip unplugged, safely cut where the trim points are
indicated.
Make sure the strip is not plugged in when cutting.
NOTE: Cutting anywhere else will permanently damage the strip.
STEP 3
Add re-connector wire to extend the strip after it is cut.
Prep the Surface & Install Your Strip
| STEP
1
Use the cleaning wipe to remove dust.
NOTE: Make sure surface is dry & free of dirt, dust and oils. For best
results, adhere the strip in temperatures above 50°F/10°C.
---|---
|
STEP 2
Working in 6 inch sections, peel off the adhesive backing.
| STEP
3
Stick to surface, 6 inches at a time, pressing and holding each section for 10
seconds.
NOTE: Adhesive may damage walls or painted surfaces if removed. Adhesive is
single use, so don’t peel lights and try to re-stick to wall. You will need to
use double-sided tape if re-application is needed.
Do not mount to wallpaper, brick, textured or porous surfaces using
adhesive. Use mounting clips instead.
Installing Without Adhesive
STEP 1
Lay out mounting clips where desired.
STEP 2
Install mounting clips by tapping the traceless nails into a suitable wall or
ceiling surface with a small hammer.
STEP 3
Push the Light Strip into each clip. Do not reposition the strip once
installed.
Bending Options
Extend (if desired) & Power On the Light Strip
STEP 1
Unplug the power supply and remove the plastic end cap cover. Attach extension
to the Light Strip.
Remember to remove plastic covers to link strips.
NOTE: Use the Snap connector to strengthen the connecting point. Extend
up to 32ft
STEP 2
Plug in power supply and turn on the Light Strip.
ENABLE LIGHT EFFECTS
Cycle through light shows by pressing the Light Effect button .
FCC Statement
Warning: Changes or modifcations to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to operate
the equipment
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help
The device must not be co-located or operating in conjunction with any other
antenna or transmitter
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(l) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
FCC RF Radiation Exposure
Statement Caution: To maintain compliance with the FCC’s RF exposure
guidelines, place the product at least 20cm from nearby persons.
IC Statement
This device complies with RS$247 of Industry Canada.
Operation is subject to the following two conditions:
(l) this device may not cause interference, and (2) this device must accept
any interference, including interference that may Couse undesired operation of
the device.
This equipment complies with IC pss-I02 radiation exposure limits set forth
for an uncontrolled environment. This transmitter must be installed to provide
a separation distance of at least 20cm from all persons and must not be
collocated or operating in conjunction with any other antenna or transmitter
Like your new Dynamic Effects
Light Strip or Extension?
Share your creations!
See the possibilities at gelighting.com/cync
PK-00108495-1
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>