TOSIMA H1 Smart Cordless Wet Dry Vacuum Cleaner and Mop User Manual

TOSIMA H1 Smart Cordless Wet Dry Vacuum Cleaner and Mop User Manual

Thanks for purchasing the Tosima Muti-Surface Floor Cleaner H1, we hope H1 will bring you a smarter and more convenient lifestyle.

If you encounter any problem not mentioned herein, please contact cs@tosima.cn.

For more details, please visit our official website: www.tosima.cn.

Please read all instructions before using this product, and keep it properly for future reference.

Safety Instructions

• H1 can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance safely and understand the hazards involved.
• This product is for home use, on non-carpet floors, such as vinyl, tile, sealed wood, marble, etc. Please do not use it outdoors.
• Do not disassemble, repair or refit H1 without authorization.
• Do not modify or attempt to repair H1 except as indicated in the manual for use and care.
• Do not use the product in an environment with the risk of fire or explosion.
• Do not use H1 to vacuum flammable materials, such as gasoline, lighter fluid, toxic material, foam liquids, paint pigments, and corrosive liquids.
• Do not use H1 to vacuum hard or sharp objects, such as nails, screws, or glass.
• Do not use H1 to vacuum things burning or smoking, such as hot ashes or cigarettes.
• Do not put any object into air openings, keep the air openings free of dust, hair, and any other things that may reduce the airflow.
• Do not wash or soak the main body and electronic accessories in water.
• Do not allow metal and conductive materials to contact the battery.
• Do not allow it to be used as a toy. Close attention is necessary when used by or near children.
• Do not touch the charging plug and docking station with wet hands.
• H1 should always be protected from long-term exposure to sunlight.
• Do not place H1 near cigarette butts, lighters, or other open fires.
• Keep hair, fingers, and other parts of the body away from openings and moving parts of the appliance.
• Only the original power adapter and battery pack can be used.
• When the metal part of the power plug is dusty, please wipe it with a dry cloth.
• The power adapter is applied to a 100-240V AC voltage. Please plug into the socket properly and keep it away from children.
• The operating temperature of the product ranges from 32°F~108°F (0°C ~ 40°C); please do not use it in a high-temperature environment.
• Plastic bags can be dangerous, please keep them away from babies and children.
• Please unplug the charger from the electrical socket when not in use or before detaching the battery pack, care, and maintenance..
• Please keep H1 away from the metal objects, such as coins, and paper clips when the battery pack is not in use.
• Do not use a battery pack that is damaged.
• Do not use with a damaged cord or plug, return the appliance to the local distributor if it has been dropped, damaged, or not working as it should.
• Do not use H1 without a HEPA filter set.
• Do not use H1 when the water depth on the working surface is more than 4mm.
• Do not block the air inlet or air outlet in case of overheating.
• Do not shake H1 hard in case the dirty water goes into the vacuum motor.
• The battery pack and charging station output terminals are not to be short-circuited.
• Please use extra care when cleaning on stairs.
• Please remove the battery from H1 before H1 is scrapped.
• Please empty it in time when the dirty water tank is full.
• Please move H1 as the manual guided in case the dirty water goes into the vacuum  motor.
• Please always clean the dirty water tank and HEPA set after each use to avoid potential pipe blockage, or it may lead to low suction power, motor overheating or reduce the life-time of H1.

Warnings

1. Do not use the rechargeable battery of this product on other devices.
2. It is forbidden to disassemble the battery pack, otherwise, the battery pack can be broken and the electrolyte will flow out, causing fire and explosion.
3. Do not short-circuit the battery. Do not store batteries haphazardly in a box or drawer where they may short-circuit each other or be short-circuited by conductive materials.
4. Do not expose the battery to heat or fire. Avoid storage in direct sunlight.
5. Do not subject batteries to mechanical shock.
6. In the event of a cell leaking, do not allow the liquid to come into contact with the skin or eyes. If contact has been made, wash the affected area with copious a mounts of water and seek medical advice.
7. Seek medical advice immediately if a cell or battery has been swallowed.
8. After extended periods of storage, it may be necessary to charge and discharge the battery several times to obtain maximum performance.

About Cleaning Solution

1. H1 may be damaged if a large amount of cleaning solution enters the motor.
2. Do not use H1 with an acidic, alkaline solution or any substances harmful to the environment.
3. Please keep children out of reach. If any solution gets into the eyes, flush them with clean water immediately. If any solution is swallowed by accident, seek medical care immediately.
4. Dirty water and solution disposal must comply with the local regulations.

What’s in the Package?

• H1 * 1 pc

• Charging Station * 1 set

• Hepa Holder* 1 pc

• Brush Holder * 1 pc

• Adapter* 1 pc

• Cleaning Tool* 1 pc

• Hepa *2 pcs (1 spare, 1 installed in H1)

• Roller Brush * 2 pcs (1 spare, 1 installed in H1)

• Hex Key * 1 pc

• User Manual * 1 pc

Accessories may be slightly different, the pictures are for reference, please subject to the actual products or confirm with the seller.

Product Model| H1
Size of Main Unit| 1135280270mm
Net Weight| About 4.90KG
Adapter Input| 100-240V ~ 50/60Hz, 0.8A
Adapter Output|
Rated Wattage| 200W
Battery Type| Li-ion Battery
Battery Capacity| 4000mAh
Battery Voltage|
Clean Water Tank Capacity| About 910 ml (Max Line 760ml)
Dirty Water Tank Capacity| About 910 ml (warning level 680±20ml @ Eco Mode)
Working Time| ≥ 35mins @ Eco Suction
Charging Time| About 5-6 hours
Working Mode| Auto Mode/Water Suction Mode / Eco Mode / Max Mode/Self-Cleaning Mode
The data comes from the lab of TOSIMA Manufacturing Co.,Ltd. It may be slightly different from the user’s data due to different usage or working environment, please subject to the actual products. For continuous product improvement, we reserve the right to any technical and design change without prior notice.

Product View

Digital Display and Function Buttons

Display Screen: Users can check the status of the battery capacity. Error Code, Electrolysis, etc.

Voice button: Short press the button lightly to turn on or off the voice.

Electrolysis: Short press the button to start electrolysis after powering on, it will  take about 32 seconds for a complete electrolysis process (from 0% to 100%). *** Electrolysed water refers to that is produced by the electrolysis of ordinary tap water containing dissolved sodium chloride. The electrolysis of such salt solutions produces a solution of hypochlorous acid and sodium hydroxide. The resulting water can be used as a disinfectant.

Eco Mode: Short press the button to enter into Eco Mode .When H1 is in Max Mode, it sprays water and washes For a longer time. Max Mode: Press the button to enter into Max Mode when H1 is in Auto Mode or in Eco-Mode. H1 will enter into the Auto Mode automatically from Max Mode in 6 minutes. H1 will not enter into the Max Mode if the battery capacity is lower than 20%.

Max Mode: Press the button to enter into Max Mode when H1 is in Auto Mode or in Eco-Mode. H1 will enter into the Auto Mode automatically from Max Mode in 6 minutes. H1 will not enter into the Max Mode if the battery capacity is lower than 20%.

Self-Cleaning: When the battery capacity is higher than 20%, put H1 back on the charging station, press the button, H1 will start electrolysis first, after that, it will enter into Self-Cleaning Mode automatically, the entire cleaning time will last about 80 seconds. If the battery capacity is lower than 20%, users need to charge H1 first. H1 can work in self-cleaning mode only when H1 is on the charging station and connected to the power supply with more than 20% battery.

Child Lock: Hold and press the “Max” Mode button and “Eco” Mode button for 3 seconds, H1 will say “Child Lock is on”. H1 will say “Switch off Child Lock before use” when pressing the function keys in Child Lock Mode.
How to switch off Child Lock:

1. Hold and press the “Max” Mode button and “Eco” Mode button for 3seconds again to switch off the Child Lock.
2. Unplug the power source to switch off the Child Lock.
3. Take H1 out from the charging station to switch off the Child Lock. H1 will say “Child Lock is off” after the above actions are done.

Dirt Monitoring Indicator: The indicator will change from blue to red according to the dirt amount. If there is too much dirt on the floor or on the dirt detection sensor, the indicator strip will be longer in Red than in Blue; if there is less dirt on the floor/dirt detection sensor, the indicator strip will be longer in Blue than in Red.

Operations

Assembly/Disassembly

1. Handle Tube
   
   Assembly:
   Insert the handle tube down into the main body until you hear the a “click” sound.

2. Clean Water Tank

Disassembly:
Hold the clean water tank holder and press the clean water tank release button, pull it outwards.

3. Dirty Water Tank
   
   
   Disassembly:
   Insert the hex key into the tube release hole, push the hex key forward, hold the  handle tube and pull it up at the same time.
   
   Assembly:
   Align the bottom of the clean water tank with the clean water tank cavity, hold the clean water tank holder and press the clean water tank release button and push the clean water tank inwards lightly.
   Disassembly:
   Hold dirty water tank holder and press the dirty water tank release button, pull it outwards.

4. Brush Guard

Disassembly:
Hold and press the brush guard lock with your thumb and index, and lift the brush guard lightly.

5. Brush Roller

Disassembly:
Hold the roller brush handle, remove it leftwards and take out the roller brush.
Assembly:
Align the bottom of the dirty water tank with the dirty water tank cavity, hold the dirty water tank and push it inwards until you hear a “click” sound.

Assembly:
Align the brush guard with the spray hole, hold and press the brush guard lock with your thumb and index, and put the brush guard on the brush base until you hear a “click” sound.

Assembly:
Hold the roller brush handle, align with the roller brush shaft B, and put the handle back into the base groove A.

Filling up the Clean Water Tank

1. The clean water tank is located on the back of the main body, hold the clean water tank holder and press the clean water tank release button, pull it outwards and take out the water tank.
   

2. Open the clean water tank lid “C”, add clean water or mixed detergent, then put back the water tank lid and attach it back to H1.

• Please keep the electrolytic electrodes of the clean water tank and its cavity clean and dry.
• Users can also add some non-corrosive or non-flammable cleaning solutions to clean the floor, DO NOT add corrosive solution, flammable liquid, or dirty water into the clean water tank.
• It is normal if there is some water in the water tank at the first use, tests and inspections have proceeded before goods leave the factory.

Charging H1

1. Connect the external charging cord to the charging base and plug the adapter into the wall outlet.
2. Please place H1 on the charging station against the wall during charging, otherwise, you may trip over the machine.
3. Place the H1 on the charging station vertically, H1 will say “Charging Starts”, and users can see the battery status on the digital display.

• Keep children out of reach.
• Please only use the original adapter for recharge.
• The H1 must be charged every 3 months if not being used for a long period.
• Please store it indoors, do not expose it to sunlight or freezing temperatures.
• Please full charge H1 at first use.

Cleaning Floors with H1

1. Preparation
   Check the Handle Tube, the Clean Water Tank, the Dirty Water Tank, the Roller Brush, the  HEPA Filter Set, etc. Make sure all of them are installed correctly and tightly, then fill up the clean water tank.

2. Start/Stop

   • Hold and press the button for 1 -2 seconds to start H1, it will enter into the Autocleaning Mode by default.
   • Short press the button to turn off H1.
   • H1 will spray water automatically in Auto Mode, Eco Mode, and Max Mode.
   • H1 will detect the dirt on the floor and adjust the suction according to the dirt amount on the floor in Auto Mode.
   • The dirt monitoring bar will change color from blue to red according to the dirt amount on the floor.

3. Suction Mode

   • Short press the button to enter into Suction Mode when H1 is in Auto-Mode, Eco Mode, and Max Mode.
   • H1 will not spray water in Suction Mode.

4. Standby

   • H1 will be on standby when it is standing upright, and will be restarted when being reclined.
   • H1 will be turned off automatically if it’s not operated within 5 minutes when on stand by.

5. Move
   Hold the handle grip and pull the H1 forward and backward to clean your floors.

   • Do not recline H1 more than 141.2° to avoid water leakage, and do not shake H1 in use.
     

6. Please empty the dirty water tank and place H1 on the charging station vertically, run the self-cleaning mode to clean the roller brush, dirty water tank, HEPA filter set, and brush guard after each use.

Important tips:

• H1 is to be used on indoor hard floors, such as sealed wood, tile, vinyl, marble, etc, use on a rough surface may not get the best performance.
• Please DO NOT use H1 to clean the long-pile rugs.
• Please DO NOT use H1 to clean the delicate rugs, silk, or similar floors.
• The Dirty Water Tank must be cleaned as soon as the cleaning work is done or it will get stinky.
• Please DO NOT bend over it before emptying the Dirty Water Tank, otherwise, dirty water will flow into the vacuum motor and damage the appliance.

Self-Cleaning

H1 can clean its roller brush and its pipe automatically on the charging station.

1. Please make sure there is enough clean water in the clean water tank. Empty dirty water tank before self-cleaning.
2. Place H1 on the charging station, and plug in the power source properly.
3. Press the Self-Cleaning button , H1 will start electrolysis first, after that, it will enter into the self-cleaning mode. It will spray clean water to clean the roller brush and pipe automatically, meanwhile, it will vacuum the dirty water and dirt into the dirty water tank.
4. It cleans the dirty water tank, HEPA filter set, and the brush guard, etc in self-cleaning. After each self-cleaning, please empty dirty water tank to avoid getting stinky. mode is finished to avoid them getting stinky.

Attention:

Please make sure the clean water tank, dirty water tank, the HEPA filter, the brush guard are properly installed when starting self-cleaning.

Care and Maintenance

Please unplug the power supply, and turn off the switch before care and maintenance.

1. For daily care and maintenance, use a soft dry mop to wipe the main body, and the charging station; use a soft damp mop to wipe the brush base, and scraper.

Dirty water tank cleaning

1. Take out the dirty water tank, open the dirty water tank lid and empty the dirty water and debris first.
2. Take out the float and HEPA filter from the dirty water tank.
3. Clean the dirty water tank, the float, and the lid with a cleaning tool and rinse them with clean water.
4. Dry the dirty water tank and its lid.

HEPA filter Cleaning

1. Take out the HEPA filter from the dirty water tank.
2. Clean it with a cleaning tool and rinse it.
3. Dry the HEPA filter.
4. Assemble the HEPA filter, and dirty water tank lid, float and put the dirty water tank back to
   H1 once they are dry.

Roller Brush Cleaning

1. Take out the roller brush as guided.
2. Use the cleaning tool to remove the debris and hair wrapped around the roller brush, then rinse it with clean water.
3. Replace with another dry and clean roller brush and put it back into the brush base.
4. Dry the wet roller brush for your next use.
   

Brush Guard Cleaning

1. Take out the brush guard as guided.
2. Use the cleaning tool to remove the debris, then rinse it with clean water.
3. Dry it and put it back to the brush base.

Suction inlet, water spray nozzle, metal scraper cleaning

1. Use a cleaning tool to remove the debris at the suction inlet.
2. Wipe the water spray nozzle, with a damp cloth to avoid blocking.
3. Use a cleaning tool to remove the debris on the metal scraper, then wipe it with a damp cloth.
   

Charging Station and Holders Cleaning

1. Unplug the power supply and take H1 out before cleaning.
2. Pour out the dirty water in Charging Station (if there is), and use a soft dry mop to wipe the charging station, brush holder, and HEPA filter holder.

Storage

1. Please dry the main body, clean water tank, dirty water tank, brush base, and HEPA set, Charging Station, brush holds, and HEPA holder, then store them.
2. The roller brush can be stored in the brush holder.

Notice:

• The Dirty Water Tank must be cleaned and dried after every single cleaning to avoid mildew or smell.
• The machine must be stored in a dry and ventilated place without heat sources.
• Please keep the machine away from direct sunlight.
• H1 should be fully charged every 3 months at least to avoid battery damage.

Cleaning / Replacement

Frequency Recommended

Note: The above frequency is only for your reference. The final cleaning / replacement frequency should be subject to your exact using habits.

Error Code

Note: Error code will be shown on the digital display if H1 is faulty, please operate H1 according to the guideline.

Trouble Shooting

• The power supply does not connect well.
• H1 Is not connected well with the charging station.

|

• Please check the connection of the power supply.
• Please re-place H1 on the charging station

**** The handle control does not work.|

• The battery capacity is low.
• The handle does not connect well.

|

• Please check the battery capacity and charge it.
• Please re-install the handle.

**** H1 doesn’t work.|

• **** The Dirty Water Tank is full.
• The Dirty Water Tank Is not installed.• The Roller Brush Is not installed.

|

• Please empty the Dirty Water Tank
• Please check and install the Dirty Water Tank.
• Please check and install the Roller Brush.

**** The vacuum is weaker than ever when cleaning.|

• **** The Hepa is blocked.
• The Hepa is wet.
• The Scraper is not installed well.
• The pipeline is blocked

|

• Please check and clean the HEPA
• Please dry the HEPA first.
• Please check and re-install the scraper.
• Please clean the pipeline.

**** The Clean Water Tank is leaking.|

• The Clean Water Tank is not installed well.
• The lid is not screwed well.

|

• Please re-install the water tank.
• Please screw the lid well.

**** No water comes out.|

• The Clean Water Tank is empty.
• The Clean Water Tank is not installed well.
• H1 is in Suction mode.

|

• Please fill up the Clean Water Tank.
• Please re-install the water tank.
• Enter into the auto mode.

**** Too much water on floor when cleaning|

• **** The Hepa is blocked or aging
• The roller brush is aging
• The scrapper is aging

|

• Please clean the Hepa or replace a new one
• Replace a new roller brush
• Replace a new scrapper

No voice|

• The voice function is off.

|

• Turn on the voice switch.

**** H1 does not work in Self- Cleaning Mode|

• **** H1 does not connect with power supply.
• The Dirty Water Tank is full.
• Clean water shortage.

|

• Please check and connect with the power supply well.
• Please empty the Dirty Water Tank.
• Please fill up the Clean Water Tank.

**** There are water drops at air outlet.|

• **** The HEPA is not installed.
• H1 was tilted hard.
• H1 vacuums the foam liquid.

|

• Please check and install the HEPA.
• Use the machine correctly.
• Empty the Dirty Water Tank in time.

**** Always get alarm “please empty the dirty water tank”.|

• **** The HEPA is blocked.
• The Dirty Water Tank is full.
• The pipe is blocked or the dirt detection sensor is dirty.

|

• Please clean the HEPA.
• Please empty the Dirty Water Tank.
• Please clean the pipe and dirt detection sensor.

H1 does not turn on|

• H1 is in auto protection for overheating.

|

• **** Restart H1 after cooling down.

If H1 still cannot work properly after the actions listed are taken, please contact the local distributor or Tosima after-sales service center.

Warranty

• The H1 has 2 years limited warranty against original defects in workmanship or material, the battery pack and the motorized parts have a 1 -year warranty.
• The warranty only applies to the authorized distributors of Tosima.
• Improper usage or not in accordance with the user manual will void the warranty.
• The application of force majeure will be invalid.
• Normal reductions, such as battery aging, HEPA aging are not guaranteed.
  • Please keep and provide your proof of purchase, S/N when making a claim.

Correct Disposal of H1

(Waste Electrical & Electronic Equipment)

The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead, it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about the recycling of this product, please contact your local council, your household waste disposal service or the shop where you purchased the product.

The product is in conformity with the essential requirements of Radio equipment
Directive 2014/53/EU that the applicable standards are:
EN300 328, EN301 489-1, EN301-489-17, IEC62311: 2020,
EN60335-1:2012+A11: 2014+A13:2017+A1: 2019+A2: 2019+A14: 2019+A15: 2021,
EN60335-2-2: 2010+A11:2012+A1: 2013

eVatmaster Consulting GmbH
Bettinastr. 30,
60325 Frankfurt am Main, Germany
contact@evatmaster.com

EVATOST CONSULTING LTD
Suite 11, First Floor, Moy Road Business Centre, Taffs
Well, Cardiff, Wales, CF157QR
contact@evatmaster.com

We reserve the right to changes in the text, design, and technical specifications which are subject to change without prior notice.

Manufacturer: Tosima manufacturing(shenzhen) Co., Ltd. Address: Room 213, Building A2, Fuhai Information Port,
Fuhai Street, Baoan District, Shenzhen City,GD, China www.tosima.cn E-mail:cs@tosima.cn

References

• Tosima Manufacturing （Shenzhen) Co., Ltd.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>