TONOR TW620 Wireless Microphone User Manual

Instruction Manual
TW620
TW630
TW820
UHF Wireless Microphone

TW620 Wireless Microphone

ABOUT THIS MANUAL

Thank you for purchasing TONOR wireless microphone. This manual is intended to help you understand all about this microphone and how to use it. TONOR always strives for the ultimate user experience. All our knowledge and passion for audio technology are incorporated into building microphones with high performance for you. The TONOR microphone is high quality and easy to use to achieve the best user experience.
Enjoy your microphone!
TONOR Team

Package Including

OPERATING ENVIRONMENTS & NOTES

When using this device, keep it away from water.
Use the device in ventilated environment, keep it away from fire.
Since it’s a wireless device, please keep it away from other interfering sources.
Don’t take apart the device.
Please use the standard power supply, high voltage may damage the device.
Please place the used batteries into the recycle bin, don’t litter them.

SPECIFICATIONS

Frequency Response: 50Hz-15Khz
Operating Frequency (US): 902.8-926.8MHz
Operating Frequency (UK/EU): 823-831MHz
Operating Range: Up to 60m
Frequency Stability: ±0.0005 MHz
SNR: 96dB
Sound Distortion: ≤0.5%
Mic Input Sensitivity: -51dBV
RF Sensitivity: -95dBm
Operating Temperature: 0˚C to +55˚C

MICROPHONE OPERATION INSTRUCTION

As shown in above pictures:

1. Display Screen
2. On/Off Switch
3. Tail Tube| 4. HI-LO Button
5. Battery Compartment
---|---

Install 2*AA batteries before using the wireless microphone and installing instruction is as follows:

1. Take down the tail tube of mic.
2. Install the batteries and tighten tail tube of mic.

Note : The positive and negative polarity of battery cannot be reversed.

Instruction:

1. Press button 2 for 2s to turn it on/off.
2. Press the HI-LO button 4, then the frequency on the screen wilI be changed.

RECEIVER INSTRUCTION FOR TW620 AND TW630

1. USB-C CHARGING PORT
2. POWER BUTTON (long press for 2 seconds to tum it on/off)
3. SIGNAL ANTENNA
4. BATTERY INDICATOR
5. RF LIGHT

LIGHT INSTRUCTION:
Battery indicator 4
Red light when shutdown charging: The receiver is in charging model.
Light off when shutdown charging: The receiver is fully charged.
Green light: The receiver is turn on.
Yellow light when turn on charging: The receiver is in charging model. The light turns green when the receiver is fully charged.
RF light 5
Turns off: The receiver is not connected to the microphone.
Stays on: The receiver and microphone are successfully connected.
Flashes quickly: The receiver and microphone are successfully connected, and the microphone is transmitting audio signals.
Flashes slowly: The power of the receiver is in a low battery status.

RECEIVER INSTRUCTION FOR TW820

1. Receiving antenna
2. Power switch (long press for 2s to tum it on/off)
3. Volume adjusting button for microphone A
4. LCD display screen
5. Volume adjusting button for microphone B

As shown in above pictures:

1. ANT B
2. BAL B
3. MIX| 4. DC IN
5. BAL A
6. ANT A
---|---

Before using the device, take out the wireless receiver from the package, and connect the following cables: firstly use the 6.35 audio cable to connect the receivers MIX’s port and other audio devices (speaker, amplifier, mixer, etc,). Secondly, erect the antenna, and connect the power cable. Thirdly, check if microphone is connected to the receiver successfully after turning on the device.

RECEIVER DISPLAY SHOWS FOR TW820

As shown in above pictures:

1. Signal levels of mic A
2. Volume levels of mic A
3. Signal receiving of mic A
4. Current channel of mic A
5. Current frequency of mic A| 6. Signal levels of mic B
7. Volume levels of mic B
8. Current channel of mic B
9. Signal receiving of mic B
10. Current frequency of mic B
---|---

When the receiver is connected to power supply successfully, but the batteries of microphone are not installed, LCD screen will display as following pictures:

When the receiver is connected to power supply successfully, and the batteries of microphone are also installed, LCD screen will display as following pictures:

TROUBLESHOOTING

No sound for TW620 (The batteries of microphone have already been installed, but the RF light(green)still flash slowly.)
Wireless Microphone ID Pairing Steps:

1. Make sure that the receiver and microphone are turned OFF.
2. Unscrew the microphone tail tube and install the batteries into the mic’s battery compartment.
3. Make sure that the microphone is OFF, press and hold the HI/LO button 4 and the power button 2 simultaneously, do not release them, until the microphone screen flashes quickly, then release two buttons simultaneously.
4. Turn on the receiver’s power button, wait for 5 seconds or so, then press the HI/LO button 4 (on the microphone) once, until the microphone screen becomes steady and no longer flashes, the RF light on the receiver turns steady, indicating that the pairing is successful.
5. Tum off the microphone, then tighten the microphone tail tube. Pairing is now completed.

No sound for TW630 (The batteries of microphone have already been installed, but one of the microphone has on sound.)
Please turn off the microphone which can work normally, then you will find that the RF light on the receiver will not stay on but flashes slowly.
Then, please follow the steps below to pair the microphone (no sound) with the receiver.
Wireless Microphone ID Pairing Steps:

1. Make sure that the receiver and microphone are turned OFF.
2. Unscrew the microphone tail tube and install the batteries into the mic’s battery compartment.
3. Make sure that the microphone is OFF, press and hold the HI/LO button 4 and the power button 2 simultaneously, do not release them, until the microphone screen flashes quickly, then release two buttons simultaneously.
4. Turn on the receiver’s power button, wait for 5 seconds or so, then press the HI/LO button 4 (on the microphone) once, until the microphone screen becomes steady and no longer flashes, the RF light on the receiver turns steady, indicating that the pairing is successful.
5. Tum off the microphone, then tighten the microphone tail tube. Pairing is now completed.

Received signal with noise or interference
Change to other channels;
Check if receiving distance exceeds the maximum range.
Microphone cannot be tumed on
Check if batteries are installed reversely;
Change to new batteries.

WARRANTY

TONOR provides 2 years of after-sales service, free replacement to products that are NOT damaged resulting from accident, alteration, misuse, negligence, or abuse. If exceeding 30 days of Amazon return policy, you can still contact us through our Shopify TONORMIC. We will serve you with full sincerity!

FCC STATEMENT: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference  that may cause undesired operation.

EASTWEST ELECTRONIC COMMERCE CO.,
LIMITED | LEVEL 54 HOPEWELL CENTRE
183 QUEEN’S ROAD EAST HONG KONG
EASTWEST ELECTRONIC COMMERCE CO US
LIMITED | 3500 SOUTH DUPONT
HIGHWAY, SUITE G106 DOVER, DE 19901
UNITED STATES
LIFEWIT LIMITED | FLAT 237, 233 HIGH
STREET CROYDON SURREY ENGLAND CR0
1FY UNITED KINGDOM
Lifewit GmbH | Friedenstraße 5 97072
Wuerzburg Germany

**https://www.tonormic.com
support@tonormic.com
MADE IN CHINA**

Documents / Resources

| TONOR TW620 Wireless Microphone [pdf] User Manual
TW620, TW630, TW820, TW620 Wireless Microphone, Wireless Microphone, Microphone
---|---

References

• Professional USB Microphone and Wireless Microphone – TONOR

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>