TONOR TW840 UHF Wireless Microphone Instruction Manual
- June 13, 2024
- TONOR
Table of Contents
TONOR TW840 UHF Wireless Microphone
ABOUT THIS MANUAL
Thank you for purchasing TONOR wireless microphone.
This manual is intended to help you understand all about this microphone and
how to use it. TONOR always strives for the ultimate user experience. All our
knowledge andpassion for audio technology are incorporated into building
microphones with high performance for you. The TONOR microphone is high
quality and easy to use toachieve the best user experience.
Enjoy your microphone!
TONOR Team
Package Including
OPERATING ENVIRONMENTS & NOTES
When using this device, keep it away from water.
Use the device in ventilated environment, keep it away from fire.
Since it’s a wireless device, please keep it away from other interfering
sources.
Don’t take apart the device.
Please use the standard power supply, high voltage may damage the device.
Please place the used batteries into the recycle bin, don’t litter them.
SPECIFICATIONS
Frequency Response: 40hz-18khz
Operating Frequency: 902.8-908.2MHz
902.8 mhz、903.4 mhz, 904 mhz, 904.6 mhz, 905.2 mhz, 905.8 mhz, 906.4 mhz,
907 mhz, 907.6 mhz, 908.2 mhz
Operating Range: Up to 60m
Frequency Stability: ±10ppm
SNR: 96dB
Sound Distortion: 0.03%
Mic Input Sensitivity: -52dB±3dB
RF Sensitivity: -95dBm
Operating Temperature: 0˚C to +55˚C
MICROPHONE OPERATION INSTRUCTION
As shown in the pictures:
- Display Screen
- On/Off Switch
- Tail Tube
- HI-LO Button
- Battery Compartment
Install 2*AA batteries before using the wireless microphone and installing instruction is as follows:
- Take down the tail tube of mic.
- Install the batteries and tighten tail tube of mic.
Note: The positive and negative polarity of battery cannot be reversed.
Instruction:
-
Press button 2 to turn on. Long press for 2 seconds to turn off.
-
Press the HI-LO button 4, then the frequency on the screen wilI be changed.
TROUBLESHOOTING
- No sound (The batteries of microphone have already been installed, but one of the microphone has on sound.)
- Please turn off the microphone which can work normally, and you will find that the RF light on the receiver will disappear. Then follow the steps below to pair the micophone (no sound) with the receiver.
- Make sure that the receiver and microphone are turned OFF.
- Unscrew the microphone tail tube and install the batteries into the mic’s battery compartment.
- Make sure that the microphone is OFF, press and hold the HI/LO button and the power button simultaneously, do not release them, until the microphone screen flashes quickly, then release two buttons simultaneously.
- Turn on the receiver’s power button, wait for 5 seconds or so, then press the HI/LO button (on the microphone) once, until the microphone screen becomes steady and no longer flashes, the RF lighton the receiver turns steady, indicating that the pairing is successful.
- Tum off the microphone, then tighten the microphone tail tube. Pairing is now completed.
- Received signal with noise or interference
- Change to other channels;
- Check if receiving distance exceeds the maximum range.
- Microphone cannot be tumed on
- Check if batteries are installed reversely;
- Change to new batteries.
WARRANTY
TONOR provides 2 years of after-sales service, free replacement to products that are NOT damagedresulting from accident, alteration, misuse, negligence, or abuse. If exceeding 30 days of Amazon return policy, you can still contact us through our Shopify TONORMIC. We will serve you with full sincerity!
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may causeundesired operation.
ISED Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNRd’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
- L’ appareil ne doit pas produire de brouillage;
- L’ appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’ en compromettre le fonctionnement.
CUSTOMER SUPPORT
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular insta llation. If this equipment does cause harmful
interferenceto radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
ISED Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement. The
device can be used installed and operated with minimum distance 0mm between
the radiator and your body.
CUSTOMER SERVICE
EASTWEST ELECTRONIC COMMERCE CO., LIMITED
LEVEL 54 HOPEWELL CENTRE 183 QUEEN’S ROAD
EAST HONG KONG
EASTWEST ELECTRONIC COMMERCE CO US LIMITED
3500 SOUTH DUPONT HIGHWAY, SUITE G106
DOVER, DE 19901 UNITED STATES
LIFEWIT LIMITED
FLAT 237, 233 HIGH STREET CROYDON SURREY
ENGLAND CR0 1FY UNITED KINGDOM
Lifewit GmbH
Friedenstraße 5 97072 Wuerzburg Germany
https://www.tonormic.com
support@tonormic.com
MADE IN CHINA
https://www.tonormic.com
support@tonormic.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>