RL56 Smart Wi-Fi Recessed LED Trim Instructions

PACKAGING CONTENTSIf a blade is bent, take the lawn mower to an

authorized Honda
servicing dealer for inspection.

ITEMS REQUIRED (Purchase separately)

• Philips Screwdriver
• Gloves

IMPORTANT SAFETY INSTRUCTIONS

When using product, basic precautions should always be followed, including the following:

• Heed all warnings, including below warnings AND those included on product.
• HALO™ recessed luminaires (fixtures) are designed to meet the latest NEC requirements and are certified in full compliance with UL. Before attempting installation of any recessed lighting luminaire check your local electrical code. This code sets the wiring standards for your locality and should be carefully studied before starting.
• Read and follow these instructions.
• Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
• To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
• Connect fixture to a 120 volt, 60 Hz power source. Any other connection voids the warranty.
• Fixture should be installed by persons with experience in household wiring or by a qualified electrician. The electrical system, and the method of electrically connecting the fixture to it, must be in accordance with the National Electrical Code and local building codes.
• WARNING – Risk of fire or electric shock. Install this kit only in luminaires that have the construction features and dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.

WARNING
Risk of Fire – MINIMUM 90°C SUPPLY CONDUCTORS. If uncertain, consult an electrician.
Risk of Electric Shock To avoid possible electrical shock, be sure that power supply is turned off at fuse box or circuit breaker before installing or servicing luminaire.

WARNING
Risk of Fire/Electric Shock – LED Retrofit Kit installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician. Luminaire wiring and electrical parts may be damaged when drilling for installation of LED retrofit kit. Check for enclosed wiring and components.
WARNING
Risk of Fire/Electric Shock

• LED connector is compatible with Halo 5” H550 Series and 6” H750 and H2750 Series LED Housings
• LED connector meets California Title-24 high-efficacy luminaire standard as a non-screw base socket.
• LED connector is a non-screwbase luminaire disconnect for tool-less installation.

CAUTION
Edges may be Sharp –
Wear gloves while handling.

INSTALLATION & MOUNTING INSTRUCTIONS

1. For ground connection, attach the preinstalled green ground wire on the light to the housing, using 1 of 3 connection methods: 1 #1
   i. Use sheet metal screw (B) to attach to 1 of 3 slots inside housing.
   ii. Drive pan head screw (C) into existing hole inside the housing.
   Note: If no hole exists, drill a small [1/8”] pilot hole and use the provided

   8 sheet metal screw (B).

   iii. Twist nut (D) onto the threaded stud in housing wall.
   Note: If no hole exists, drill a small pilot hole and use the provided #8 sheet metal screw.
   

2. Skip this step if the housing is already equipped with an orange quick connector. If installed:
   Remove the mounting bracket and plate from inside the housing and then remove the socket from the plate. Then screw the Socket Adapter (B) into the housing.

3. Plug the orange quick connect into the light.
   

4. Skip this step if installing into a 6” housing. For 5” housings: Loosen screws on top brackets and slide them into the 5” position & retighten the screws.

5. Press both pairs of torsion spring legs together and insert them into the receivers inside the housing.

6. Setup and Control
   DiYers & Homeowners: Configure and control lighting quickly using the WiZ App.
   Installers: Use the WiZ Pro Setup App for initial claiming and configuration over Bluetooth and to manage multiple projects.
   Then control with advanced features using the WiZ Pro Dashboard and WiZ App once Wi-Fi is connected. For more information visit: pro.wizconnected.com

WiZ App
| WiZ Pro Setup App

---|---

https://uqr.to/172bw

|

https://uqr.to/172ct

UNINSTALLING

Torsion Springs Method

1. Pull down firmly on the module until it stops.
2. Reach between the flange of the light (inside the can) and squeeze legs together to remove the fixture.
3. Unplug the orange connector and remove the ground wire.

Friction Clips Method

1. Twist the fixture (about 60°) counterclockwise to release the grip of the friction clips.
2. Pull down firmly on the fixture to remove it from the housing.
3. Unplug the orange connector and remove the ground wire.

ALTERNATE INSTALLATION – FRICTION CLIPS

Friction Clips Method

1. Unscrew the torsion spring brackets from the module and discard.
2. Insert friction clips into friction clip holders making sure that they are fully seated, and locking feature engages (indicated by a click).
3. Properly wire the unit as instructed in WIRING section of these instructions.
4. Make sure all 3 friction clips are full expanded by rotating the clips as shown.
5. Align the module in the center of the recessed housing and firmly press the light fixture upward into it.

FCC STATEMENT

FCC Statement

• This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
  • (1) This device may not cause harmful interference.
  • (2) This device must accept any interference received, including interference that may cause undesired operation.
  Note: The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment.
  Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

• This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help

RF Exposure Statement

• This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.

IC Statement

• This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
  Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

• This device complies with ISED ICES Standard Canada ICES-005(B) / NMB-005 (B)

IC 20cm RF

• This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.
• This device complies with industry Canada license-exempt RSS-247 standard(s).
• This equipment complies with FCC & IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.
• Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
• This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: – (1) This device may not cause interference; and – (2) This device must accept any interference, including interference that may cause undesired operation of the device.
  FCC ID – 2AC7Z-ESP32SOLO1
  IC Code – 21098-ESP32SOLO1
  SAVE THESE INSTRUCTIONS AND WARNINGS.

5 LIMITED YEAR WARRANTY

Guaranteed to last 5 years based on up to 6 hours usage per day. For limited warranty details and restrictions visit: www.cooperlighting.com/warranty

https://uqr.to/1bj8z

COMPATIBLE HOUSINGS

Before proceeding, confirm your recessed housing is compatible with RL56 LED Retrofit Modules. A list of the most common housings is provided below. Along with those noted below the RL56 LED Retrofit Modules are UL Certified for use with any 5” or 6” diameter recessed housing constructed of steel or aluminum with an internal volume that exceeds 108 in. 3 and does not exceed the input rating of the housing.

• HALO ® : H7ICAT, H7ICT, H7T, H7ICATNB, H7ICTNB, H7TNB, H7UICAT, H7UICT, H7TCP, H7RICAT, H7RICT, H7RT, H27ICAT, H27ICT, H27T, H27RICAT, H27RICT, H27RT, H5ICAT, H5ICATNB, H5RICAT, H5T, H5TNB, H5RT, H5TM, H25ICAT, H25ICATNB, E27ICAT, E27RICAT, E27RTAT, E27TAT, E7ICAT, E7ICATNB, E7RICAT, E7RTAT, E7TAT, E7TATNB, E5ICAT, E5ICATNB, E5RICAT, E5RTAT, E5TAT, E5TATNB
  HALO ® LED: H750ICAT, H750RICAT, H750T, H750TCP, H2750ICAT, H2750RICAT, H550ICAT, H550RICAT, E550ICAT, E550RICAT, E750ICAT, E750RICAT

• HALO ® LED Retrofit: ML7BXRFK, ML7E26RFK

• Juno: IC22, IC22R, IC22W, IC22S, IC23, IC23W, IC21, IC21R, IC2, TC2, TC2R, IC20, IC20R, IC25, IC25R, IC25W, IC25S, TC20, TC20R

• Lightolier: 1104ICS, 1104ICR, 1104SIC, 1104SICR, 1004ICS, 1004ICR, 1004SIC, 1004SICR

• Capri: CR1, PR1, QL1, R9ASIC, R5

• Progress: P86TG

• Lithonia: L7X, L7XP

• Thomas: PS1, R9ASIC/PS9RM

• Prescolite: IBXS

• Commercial Electric: C7ICA (H3), H18

• Elco: (HL7ICA) EL7ICA

Cooper Lighting Solutions 1121 Highway 74 South Peachtree City, GA 30269
P: 770-486-4800
www.cooperlighting.com

© 2022 Cooper Lighting Solutions
All Rights Reserved.

Specifications and dimensions subject to change without notice.

IL518126ML
September 14, 2022 5:15 PM

References

• WiZ Pro

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>