LNC A04976W1 6 in W 1 Light Polished Gold Instruction Manual

: June 15, 2024
: LNC

Table of Contents

LNC A04976W1 6 in W 1 Light Polished Gold
Product Information
Product Usage Instructions
TOOLS REQUIRED
ASSEMBLY & INSTALLATION INSTRUCTIONS
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LNC A04976W1 6 in W 1 Light Polished Gold

Product Information

Item Number: A04976W1
Maximum Wattage : Type B, Max 40W per bulb
Voltage : 120V

Product Usage Instructions

We suggest installation by a licensed electrician.
Before starting the installation, turn off the power to ensure safety.
Mounting surface should be clean, dry, flat, strong enough, and 1/4 larger than the canopy on all sides. Correct any gaps exceeding 3/16 as required.
Ensure that the ceiling or wall can withstand the weight of the lamp before installation.
Keep the lamp away from acidic and alkaline substances to prevent damage to the surface.
When replacing bulbs, turn off or unplug the lamp and wait until it cools down as bulbs get hot quickly.
Use common sense, caution, and care when working with electrical products.

Tools Required (Not Included):

Ladder
Philips Head or Flat Blade Screwdriver
Electrical Tape
Pliers
Wire Cutter/Stripper

Parts Included:

(C) Green ground screw (1)
(D) Mounting plate (1)
(E) Back plate (1)
(F) Knob nut (2)
(G) Socket (1)
(H) Iron shade (1)
(I) Socket ring (1)

Accessories Enclosed:

(A) Mounting screw (2)
(B) Plastic wire connector (3)

Assembly & Installation Instructions:

Carefully remove the fixture from the carton and check that all parts and accessories are included.
Secure mounting plate (D) to the outlet box with mounting screws (A).
Connect wires according to the provided chart. Never connect other wires to ground wires.

Item Number: A04976W1

WARNING (To reduce the risk of fire, electric shock, or personal injury):

We suggest installation by a licensed electrician.
Please read the instruction carefully and save it as you may need it at a later time.
Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home.
- Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
Make sure that the ceiling or wall can stand the weight of the lamp before installation.
Make sure the voltage you are using is 120V. The maximum wattage is Type B, Max 40W per bulb.
Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT:

TOOLS REQUIRED

(NOT INCLUDED):

Before starting assembly and installation please prepare the needed tools as below picture

PARTS INCLUDING:

(C) Green ground screw (1)
(D) Mounting plate (1)
(E) Back plate (1)
(F) Knob nut (2)
(G) Socket (1)
(H) Iron shade (1)
(I) Socket ring (1)

ACCESSORIES ENCLOSED:

(A) Mounting screw (2)
(B) Plastic wire connector (3)

ASSEMBLY & INSTALLATION INSTRUCTIONS

Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
Turn off power
- Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home.
- Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
Make assembly

Step A1
- Unscrew knob nuts (F) from mounting plate (D) and back plate (E), then set them aside for later installation.
Step A2
- Carefully pass the supply wires from the outlet box through mounting plate (D).
- Secure mounting plate (D) to the outlet box with mounting screws (A).
Step A3
Make wire connections
- Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE
- COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
- Connect ground wires according to the below chart
- Connect wires according to the below chart
- Note : When parallel wires (SPT I& SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)
- Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
Step A4
- Align the holes in back plate (E) with the pre-assembled mounting screws, then attach back plate (E) to mounting plate (D) with the previously removed knob nuts (F). Hand tighten until snug.
  NOTE : back plate (E) should be snug against the wall with knob nuts (F). If not, remove back plate (E), adjust the threaded length of pre-assembled mounting screws on mounting plate assembly (D):
- Unscrew the pre-assembled hex nuts.
- Screw the pre-assembled mounting screws in or out of mounting plate (D).
- When the secure length is achieved, tighten the pre-assembled hex nuts and back to Step A4.
Step A5
- Remove socket ring (I) from socket (G).
- Fix iron shade (H) to socket (G) with socket ring (I).
- Install the bulb (Not included) (Please do not exceed the maximum wattage recommended on the socket.)

Check everything is installed properly, then you could turn on the light. Enjoy!

ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

CLEANING