Q-TRAN Extrusion – TALO Sleek Flat Lens LED Aluminum Extrusion Instruction Manual

Q-TRAN Extrusion – TALO Sleek Flat Lens LED Aluminum Extrusion

Product Information

This product is an extrusion called TALO that is compliant with industry standards. It comes with a 5-year warranty. The product is suitable for various installations and methods.

The components and hardware included with the product are:

• Plastic T-BAR-Clip (PLC-01)
• Standard 1(15/16) grid clips (SST-02)
• Hinge brackets (HMB-M, HMB-L, HMB-XL)
• Q-ANGLE
• Q-PIVOT
• Screws (#4 x 5/8 Flat Head SS)
• Silicone (sold separately)
• VHB Tape (sold separately)

The product is ideal for various applications such as office, retail, hospitality, education, laboratory, residential, lobby, institutional, and transportation. It can be used for cove, under and over cabinet lighting, shelf lighting, display cabinet lighting, signage lighting, and more.

Product Usage Instructions

Before installation, please read all instructions carefully.

For installation, you have the following options:

1. Plastic T-BAR-Clip method: Use the Plastic T-BAR-Clip (PLC-01) and follow the provided dimensions for installation on walls, ceilings, or floors. The clip can be used with the Standard 1(15/16) grid clips (SST-02) for additional support.
2. Adhesive Mount method: Use adhesive (sold separately) to mount the product on concrete walls. You can use silicone or VHB Tape (both sold separately) for the installation.

Note: The product is not rated for walkover on the floor.

For different applications, you may require additional accessories:

• Hinge brackets (HMB-M, HMB-L, HMB-XL): These brackets can be used for specific mounting needs.
• Q-ANGLE: Use these pairs of Q-ANGLE accessories for specific angles in your installation.
• Q-PIVOT: Use these pairs of Q-PIVOT accessories for specific pivoting requirements.

For cutting, assembly, and wiring options, please refer to the provided diagrams and instructions in the manual.

INSTALLATION INSTRUCTIONS

ATTENTION: Please read all instructions BEFORE installation

• Product to be installed by a licensed electrician
• Always ensure power supply connection to electrical circuit is disconnected before working on it
• Follow diagram to connect Secondary Voltage wires to power supply. Refer to Q-Tran power supply instructions for wiring
• Use only with Class 2 power supply unit — Compatible for use with Q-Tran power supplies
• Surface mount
• Suitable for DRY, DAMP, and WET locations
• Suitable for installation in storage area of a clothes closet when assembled as a finished extrusion up to 4W/ft at Q-Tran facility
• Not rated for walkover
• Input Voltage: 24VDC
• Diagrams for representation only and not to scale
• Once a wet strip or a damp strip is cut, it cannot be reconnected.

METHODS OF INSTALLATION

SURFACE MOUNTING METHOD

• VHB Adhesive Mount (page 9-10)
• Silicone Mount (page 11)
• Hidden Stainless Steel Clip Mount (page 12)
• Plastic T-BAR Clip Mount (page 13)

Cove, Under & over cabinet:
Ideal for office, retail, hospitality, education, laboratory, and residential.

Shelf:
Ideal for office, retail, hospitality, education, laboratory, and residential.

Display cabinet:
Ideal for retail and hospitality.

Signage:
Ideal for lobby, retail, hospitality, institutional, and transportation.

COMPONENTS & HARDWARE

ACCESSORIES SOLD SEPARATELY

NOTES:

HIDDEN STAINLESS STEEL CLIP| PLASTIC T-BAR CLIP
• 2 clips provided for 4’ or less; 4 clips provided for greater than 4’| • 2 Clips provided per first 12”, 1 clip provided per additional foot.

LED STRIP LEAD WIRE & JUMPER INSTRUCTIONS: DRY IP20

If LED wires are pre-soldered from the factory, skip to page 7.

1. Measure and cut LED strip to desired length with scissors along the cut point.

2. Solder lead wire onto solder pad. Confirm wires are matched up correctly before soldering. See wiring diagrams below for specific light engine details.
   NOTE: Recommended soldering iron temperature of 650˚ – 700˚F for lead- free solder

3. NOTE:
   Connect LED to power supply to ensure it is working properly and all non- factory soldered connections are secure before proceeding with step #3.

ONCE ALL CONNECTIONS ARE FUNCTIONING PROPERLY, DISCONNECT POWER AND BEGIN HEAT SHRINKING INSTRUCTIONS BELOW:-

• a: Place 1st sleeve (1/2” Shrink Tube ) on lead wire.
• b:  Shrink the tube with heat gun.
• c: Place 2nd sleeve (1” Shrink Tube ) on lead wire.
• d: Shrink the tube with heat gun.

LED STRIP LEAD WIRE & JUMPER INSTRUCTIONS: DMP IP54

1. Measure and cut LED strip to desired length with scissors along the cut point.

   • Carefully peel polyurethane back to expose the solder pads.

2. Solder lead wire onto solder pad. Confirm wires are matched up correctly before soldering. See wiring diagrams below for specific light engine details.
   NOTE: Recommended soldering iron temperature of 650˚ – 700˚F for lead- free solder.

3. NOTE:
   Connect LED to power supply to ensure it is working properly and all non- factory soldered connections are secure before proceeding with step #3.

ONCE ALL CONNECTIONS ARE FUNCTIONING PROPERLY, DISCONNECT POWER AND BEGIN HEAT SHRINKING INSTRUCTIONS BELOW:

• a: Place 1st sleeve (1/2” Shrink Tube ) on lead wire.
• b: Shrink the tube with heat gun.
• c: Place 2nd sleeve (1” Shrink Tube ) on lead wire.
• d: Shrink the tube with heat gun.

LED STRIP LEAD WIRE & JUMPER INSTRUCTIONS: WET IP67

1. Measure and cut LED strip to desired length with scissors along the cut point.

2. Solder lead wire onto solder pad. Confirm wires are matched up correctly before soldering. See wiring diagrams below for specific light engine details.
   NOTE: Recommended soldering iron temperature of 650˚ – 700˚F for lead- free solder.

3. NOTE:
   Connect LED to power supply to ensure it is working properly and all non- factory soldered connections are secure before proceeding with step #3.

ONCE ALL CONNECTIONS ARE FUNCTIONING PROPERLY, DISCONNECT POWER AND BEGIN HEAT SHRINKING INSTRUCTIONS BELOW:

• a: Place lead wire cap over wire
• b: Add silicone inside connector and glue around the edge to secure gap; allow time for glue to dry.
• c: Place end cap over the end of LED
• d: Add silicone inside connector and glue around the edge to secure gap; allow time for glue to dry.

NOTES:

• Avoid bending in sharp angles which may damage the LED.
• Always test LED operation before installing in extrusion. Connect LED to power supply to ensure it is working properly and all non-factory soldered connections are secure.
• Diagrams for representation only and not to scale.

CUTTING EXTRUSIONS FOR IN-FIELD ASSEMBLY INSTALLATION

Q-Tran strongly recommends cutting the extrusion and lens together to achieve a clean cut.

• To achieve corners or angles, measure the LED extrusion to desired length and cut with a miter saw.
• For straight runs, measure LED extrusion to desired length and cut it with a circular saw.

NOTE: Using the proper blade for aluminum, cut to the desired length. Recommend using a 10 in.x 80 tooth medium aluminum saw blade.

CONTINUOUS WIRING CONFIGURATION OPTIONS

Review wire method to ensure clean installation prior to mounting extrusion.

NOTE: Additional wire methods include:

• S1 & S2: Connector/Wire Input only
• P1 & P2: Connector/Wire Input and Output

LED INSERTION FOR IN-FIELD ASSEMBLY INSTALLATION

STRIP IN EXTRUSION

1. Using a 50/50 alcohol mix, thoroughly clean surface area of the extrusion. Allow 5 minutes to dry.
2. Peel back 0.5″ of the VHB tape’s protective film on one end of LED and use firm pressure to adhere it to the extrusion, avoiding air bubbles. Continue peeling the film and adhering the strip in small sections until the entire length is installed.
3. Flat Lenses: Apply uniform pressure until the extrusion and lens snap securely together.
4. Add glue inside the end cap and glue around edges to secure end cap in place. Do not allow glue to come in contact with LED.

SURFACE MOUNTING METHOD

SURFACE PREPARATION

1. Temperature and environmental concerns:
   • Ideal application environment is 70-100ºF in 50% humidity or less.
   • Minimum application temperature: 50ºF
   • This temperature and humidity should be maintained for 72 hours after application for maximum bond strength.
2. Using a 50/50 alcohol mix, thoroughly clean the backside of the extrusion and the surface area where extrusion will be installed. Allow 5 minutes to dry.
   • Peel back 0.5″ of the VHB tape’s protective film on one end and use firm pressure to adhere it to the desired surface, avoiding air bubbles. Continue peeling the film and adhering the tape in small sections until the entire length is installed.
3. For porous materials (Wood, Brick, Concrete etc.) apply two layers of paint or primer to the surface. This will help create a better bonding surface for these materials. These can be purchased from a local hardware store.

Two-Part Epoxy
ABS, Fiberglass, Plastic, and PVC| Loctite Plastic Two-Part Epoxy
Tile, Wood, Ceramic, Glass, or Metal| Loctite Clear Two-Part Epoxy
All Purpose| Strong Stik

SURFACE MOUNTING METHOD: VHB ADHESIVE
BEFORE installation, the surface must be thoroughly cleaned and dried for maximum bond strength.

1. Determine the TALO extrusion(s) location and positioning on desired surface before adhering extrusion to surface. Make any necessary reference markings to indicate extrusion placement.
2. To adhere the VHB adhesive, peel the white film back while evenly applying the tape to the mounting side of the extrusion. The red side should be visible.
   • Remove the red film and position extrusion in place according to your previous reference marking(s).
3. Remove protective film from the surface of the extrusion’s lens.

NOTES: EPOXY ALTERNATIVE: For improved bonding strength, apply a small amount of epoxy at each end. Refer to table on f o r suggested epoxies. These can be purchased at a local hardware store. Please follow all manufacturer instructions for suggested epox y.

SURFACE MOUNTING METHOD: SILICONE

2 clips provided for 4’ or less; 4 clips provided for greater than 4

1. Determine the TALO extrusion(s) location and positioning on desired surface; evenly distribute clips. Make any necessary reference markings to indicate where each clip is to be secured in place. Recommended every 24” – 30”.

2. Firmly press the silicone-coated clips on the marked reference points.

   • Wait for silicone adhesive to cure completely before snapping extrusion into place.
   • Snap extrusion onto clips.
     NOTE: Cure time is dependent on the type of silicone adhesive used.
     Refer to silicone product manufacturer for accurate drying time.

3. Remove protective film from the surface of the extrusion’s lens.

SURFACE MOUNTING METHOD: HIDDEN STAINLESS STEEL CLIPS

2 clips provided for 4’ or less; 4 clips provided for greater than 4’

1. Determine the TALO extrusion(s) location and positioning on desired surface; evenly distribute clips. Make any necessary reference markings to indicate where each clip is to be secured in place. Recommended every 24” – 30”.

2. Secure clips using the #4 flat head hardware provided.

   • Ensure the screw head is flush with the clip’s base.
   • Snap extrusion onto clips.
     NOTE: Flat head screw type is dependent on surface/application material.
     Alternative flat head screws may be required. Refer to the surface material manufacturer for suggested screw type.

3. Remove protective film from the surface of the extrusion’s lens.

SURFACE MOUNTING METHOD: PLASTIC T-BAR CLIPS

2 Clips provided per first 12”, 1 clip provided per additional foot.

1. Determine the TALO extrusion(s) location and positioning on desired surface; evenly distribute clips. Make any necessary reference markings to indicate where each clip is to be secured in place. Recommended every 12”.
2. Snap extrusion onto T-BAR.
3. Remove protective film from the surface of the extrusion’s lens.

© 2023 Q-Tran Inc. All rights reserved
155 Hill St. Milford, CT 06460
203-367-8777
sales@q-tran.com 
www.q-tran.com
Specification subject to change. Rev-10-10-23

References

• Your Name as Your Email | Hover Realnames
• LED Lighting Systems, Linear LED Lights, LED transformers | Q-Tran

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>