Flyfish VOLADORVD7 FPV Drones User Guide
- September 19, 2024
- Flyfish
Table of Contents
Flyfish VOLADORVD7 FPV Drones
Product Introduction
Aircraft configuration information
-
RACKS
wheelbase:295mm -
DYNAMICAL SYSTEM
Motor: Hawk 2807 1300kv
blade: HQProp 7*483 -
ESC
Hakrc 50A Stack
Drive Type: brushless DC drive -
FLIGHT CONTROLLERS
Flight controller model: Hakrc FF F405
Firmware type: betaflight -
IMAGE ACQUISITION SYSTEM
RunCam Phoenix 2 sp
Image Mode : Simulates an image -
IMAGE TRANSMISSION SYSTEM
2.5W 5.8G
Simulated video transmission -
REMOTE CONTROL LINK
RLRS Lora
correspondence
Frequency bands :433MHZ
Flight distance: 15km -
ENERGY SYSTEM
Lithium polymer batteries
Recreational flights
-
Recreational flights
-
commerce Aerial photography
-
Mission flights
-
Sporting events
Directions for use
-
Aircraft batteries
Place the battery with the straps that come with the package fixed to the base plate of the rack, The battery is facing one end with the power connector Tail direction. -
The aircraft and the remote controller are linked batteries The remote control first enters the linking mode, Quickly plug and unplug the aircraft power cord three times in a row (Keep the aircraft powered on for the last time)
Confirm that the receiver indicator is in the blue light flashing slowly Indicates that the linking mode has been successfully entered, Wait for the receiver indicator to turn solid to indicate successful binding -
Airplanes and glasses Alignment
Plug in the aircraft first and turn on the glasses Automatic frequency search using glasses/ Manual FM adjusts the frequency point of the glasses to The frequency is the same as that of video transmission Check if there is an image on the glasses screen There is a continuous image screen Indicates that the aircraft and glasses are successfully linked -
Check before you fly
After the aircraft is powered on and the linking is successful, Press the unlock switch of the remote control without the spiral prize installed, Visually check if the motor is working properly
( Note: Confirm that the motor rotation direction is correct)
Check whether the image transmission system is normal -
Install the propellers
-
Precautions for flying
-
Check the battery level before flying
-
Check the electromagnetic environment for interference before flying
-
Make sure the flight path is free of obstructions
Maintenance instructions
Aircraft Maintenance Instructions
- The aircraft should be checked regularly for screw tightness
- Do not use highly corrosive solvents to clean the aircraft, improper operation will cause damage to circuit boards and structural parts
- To clean the lens, wipe it with a cloth designed for glasses
Battery Maintenance Instructions
- Long-term storage of the battery requires charging until storage The voltage is about 3.85V before storage
- Pouch batteries are kept away from fire sources and sharp appliances, Prevent spontaneous combustion
- It is recommended to use the battery at a reasonable ambient temperature Use the battery to ensure full performance
- Lithium batteries need to be charged with a special balanced charger.
Do not use a non-certified ordinary charger for charging
Glasses Maintenance Instructions
- When not in use, store your glasses in an environment that is not easy to be bumped, and it is recommended to use a special protective backpack for storage
- The antenna of the image system is not bent, which can easily cause damage to the antenna
- It is recommended to store the glasses and the glasses-powered battery separately
- Avoid storing glasses in humid, extreme high and low temperatures, to maintain the expected service life of the product
FCC Warnning
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly
approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>