EGO Power Plus ST1300E-S 56 Volt Lithium-Ion Cordless Line Trimmer Instruction Manual

June 12, 2024
EGO POWER PLUS

EGO Power Plus ST1300E-S 56 Volt Lithium-Ion Cordless Line Trimmer Instruction Manual
Cordless Line Trimmer

READ ALL INSTRUCTIONS!

WARNING: Residual risk! People with electronic devices, such as pacemakers, should consult their physician(s) before using this product. Operation of electrical equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker.

WARNING: The operation of any power tools can result in foreign objects being thrown into your eyes, which can result in severe eye damage. Before beginning power tool operation, always wear safety goggles or safety glasses with side shields and a full face shield when needed. We recommend a Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields.

SPECIFICATIONS

Voltage 56 V
**** No-load Speed High: 6500 /minLow: 5200 /min
Cutting Mechanism Bump Head
Cutting Line Type 2.0mm Nylon twist line
Cutting Width 33 cm
Recommended Operating Temperature 0°C-40°C
Recommended Storage Temperature -20°C-70°C
Weight (without battery pack) 2.76 kg
Measured sound power level LWA 92.1 dB(A) K=1.6 dB(A)
Max. sound pressure level at operator’s ear LPA 72.6 dB(A) K=2.5 dB(A)
Guaranteed sound power level LWA (according to 2000/14/EC) 94 dB(A)
**** Valuation of vibration ah Front handle
Rear handle 1.9 m/s2 K=1.5 m/s2
  • The declared vibration total value has been measured in accordance with a standard test method and may be used for comparing one tool with another;
  • The declared vibration total value may also be used in a preliminary assessment of exposure.

NOTICE: The vibration emission during actual use of the power tool can differ from the declared value in which the tool is used;In order to protect the operator, user should wear gloves and ear protectors in the actual conditions of use.

DESCRIPTION

KNOW YOUR LINE TRIMMER (Fig. A1)
Instruction

  1. Trigger
  2. Rear Handle
  3. Lock-off Lever
  4. Speed Adjustment Switch
  5. Soft Sleeve
  6. Adjustable Front-assist Handle
  7. Trimmer Head (Bump Head)
  8. Bump Knob
  9. Line-cutting Blade
  10. Guard
  11. Ejection Mechanism
  12. Electric Contacts
  13. Latch
  14. Battery-release Button

ASSEMBLY

UNFOLDING THE SHAFT
Instruction
Instruction

WARNING: Do not hold the shaft at the joints in order to avoid pinching your hands or fingers. WARNING: Do not attempt to start the trimmer until the shaft has been locked. Unfold the shaft gently, ensuring the cable inside the shaft, and lock it with two screws by the supplied wrench (Fig. B1 & B2).

MOUNTING THE GUARD
Instruction

Align the guard mounting holes with the assembly holes and then lock the guard onto the shaft base with the two screws. Make sure the guard is fixed according to Fig. C , any reverse fixing will cause great danger!

MOUNTING AND ADJUSTING THE FRONT-ASSIST HANDLE
Instruction
Instruction
Instruction
Instruction
Instruction
Instruction
Push the front-assist handle onto the shaft (Fig. E) , then insert the clamping block into the handle slot (Fig. F), mount the lock pole, lock them with the wing nut (Fig. G). The sequence is as Fig. D shown. Lastly, adjust the front-assist handle position to make sure your front arm is straight when using the trimmer (Fig. H) and then lock the lever of the lock pole (Fig. I)

WARNING: Only fix the front-assist handle in front of the soft sleeve on the shaft.

WARNING: The tool can not be used without the front-assist handle reliably fixed

OPERATION

WARNING: Do not allow familiarity with this product to make you careless. Remember that a careless fractionof a second is sufficient to inflict serious injury.

WARNING: Always wear eye protection with side shields. along with hearing protection. Failure to do so could result in objects being thrown into your eyes and other possible serious injuries.

WARNING: Do not use any attachments or accessories not recommended by the manufacturer of this product. The use of attachments or accessories not recommended can result in serious personal injury.

WARNING: Use your line trimmer equipped with the appropriate cutting line only for cutting grass and similar material. You may use this product for the purposes listed below:

Trimming: used for removing grass and weeds up against walls, fences, trees and borders.

Cutting: used for cutting the grass that is difficult to reach using a normal mower.

NOTICE: The tool is to be used only for its prescribed purpose. Any other use, for example edge trimming, is deemed to be a case of misuse.

ATTACHING/DETACHING THE BATTERY PACK

To Attach
Instruction

Align the battery ribs with the mounting slots and press the battery pack down until you hear a “click” (Fig. J).

To Detach
Instruction

Depress the battery-release button and pull the battery pack out as Fig. K shown.

HOLDING THE LINE TRIMMER

WARNING: Dress properly to reduce the risk of injury when operating this tool. Do not wear loose clothing or jewelry. Wear eye and ear/hearing protection. Wear heavy duty, long trousers, boots and gloves. Do not wear short trousers, sandals or go barefoot

Instruction
Before operating, hold the trimmer with both hands, one hand on the rear handle and the other on the front-assist handle which shall be straight (Fig. L). Then check for balanced footing and a proper cutting distance without operator bending over.

STARTING/STOPPING THE LINE TRIMMER

To Start
Instruction

Press down the lock-off lever and hold it in that position. Depress the trigger to turn on the line trimmer as Fig. M shown.

To Stop
Release the lock-off lever and the trigger.

NOTICE: The motor has two speeds for cutting, Position“1” for lower speed and Position “2” for high speed, as Fig. M shown. Just push the speed adjustment switch to the suitable position during cutting.

ADJUSTING CUTTING LINE LENGTH
Instruction

The bump head allows the operator to release more cutting line without stopping the motor. As line becomes frayed or worn, additional line can be released by lightly tapping the bump knob on the ground while operating the trimmer (Fig. N).

NOTICE: Line release will become more difficult as the cutting line becomes shorter.

WARNING: Do not remove or alter the line cutting blade assembly. Excessive line length will cause the motor to overheat and may result in serious personal injury

There are two methods to replace the cutting line:

  1. Wind the spool with new line.
  2. Install a pre-wound spool (AS1302, if necessary, available in dealer).

Wind the spool with new line
Instruction
Instruction
Instruction
Instruction
Instruction
Instruction
Press the two release tabs on the spool base and pull the spool retainer out (Fig. O). Take out approximately 5m of 2.0mm diameter cutting line. Fold and wind it onto the spool as Fig. P & Q shown. Then place the line ends through the two opposite notches in the spool (Fig. R) and place the spool into its retainer with notches aligned with retainer eyelets (Fig. T). Lastly, align the retainer slots with the tabs on the spool base and press the retainer evenly down, ensuring that it snaps into place (Fig. S).

NOTICE: Always clean the spool retainer, spool and spool base before reassembling the trimmer head. Check the spool retainer, spool and spool base for wear. If necessary, replace the wear parts.

NOTICE: Failure to wind the line in the direction indicated will cause the trimmer head to operate incorrectly.

MAINTENANCE

WARNING: When servicing, use only identical replacement parts. Inspect and maintain the machine regularly. To ensure safety and reliability, all repairs should be performed by a qualified service technician.

WARNING: Battery tools do not have to be plugged into an electrical outlet; therefore, they are always in operating condition. To prevent serious personal injury, take extra precautions and care when performing maintenance, service or for changing the cutting attachment or other attachments.

WARNING: To prevent serious personal injury, remove the battery pack from the tool before servicing, cleaning, changing add-on attachments or removing material from the unit.

CLEANING THE UNIT

  • Clean the unit using a damp cloth with a mild detergent.
  • Do not use any strong detergents on the plastic housing or the handle. They can be damaged by certain aromatic oils, such as pine and lemon, and by solvents such as kerosene. Moisture can also cause a shock hazard. Wipe off any moisture with a soft drycloth.
  • Use a small brush or the air discharge of a small vacuum cleaner brush to clean the air vents on the rear housing.

STORING THE UNIT

  • Remove the battery pack from the line trimmer when it is not in use.
  • Clean the tool thoroughly before storing it.
  • Store the unit in a dry, well-ventilated area, locked-up or up high, out of the reach of children. Do not store the unit on or adjacent to fertilizers, petrol, or other chemicals.

Protecting the environment
 Do not dispose of electrical equipment, used battery and charger into household waste! Take this product to an authorized recycler and make it available for eparate collection. Electric tools must be returned to an environmentally compatible recycling facility

TROUBLESHOOTING

PROBLEM CAUSE SOLUTION
**** Line trimmer fails to start. ◾      The battery pack is not

attached to the line trimmer.◾      No electrical contact between the trimmer and battery.◾      The battery pack is depleted.◾      The lock-off lever and trigger are not depressed simultaneously.| ◾      Attach the battery pack to the line trimmer. ◾      Remove battery, check contacts and reinstall the battery pack.◾      Charge the battery pack.◾      Press down the lock-off lever and hold it, then depress the trigger to turn on the line trimmer.
****
Line trimmer stops while cutting.| ◾ The guard is not mounted on the trimmer, resulting in an overly long cutting line and motor overload.◾      Heavy cutting line is used. ◾      The motor shaft or trimmer head is bound with grass.◾      The motor is overloaded. **** ◾      The battery pack or line trimmer is too hot.◾ The battery pack is disconnected from the tool.◾      The battery pack is depleted.| ◾      Remove the battery pack and mount the guard on the trimmer. **** ◾      Use standard nylon cutting line with diameter no more than 2.0mm.◾      Stop the trimmer, remove the battery, and remove the grass from the motor shaft and trimmer head.◾      Remove the trimmer head from the grass. The motor will recover to work as soon as the load is removed. When cutting, move the trimmer head in and out of the grass to be cut and remove no more than 20cm of length in a single cut.◾      Allow the battery pack or trimmer to cool until the temperature drops below 67°C.◾      Re-install the battery pack. ◾      Charge the battery pack.
****
Trimmer head will not advance line.| ◾      The motor shaft or trimmer head is bound with grass.◾      There is not enough line on the spool. ◾      The trimmer head is dirty. ◾      Line is tangled on spool. **** ◾      The line is too short.| ◾      Stop the trimmer, remove the battery, and remove the grass from the motor shaft and trimmer head.◾      Remove the battery and replace the cutting line; follow the section “LINE REPLACEMENT” in this manual.◾      Remove the battery and clean the spool, spool retainer and spool base.◾      Remove the battery, remove the line from the spool and rewind; follow the section “LINE REPLACEMENT” in this manual.◾      Remove the battery and pull the lines while alternately pressing down on and releasing the bump knob.

WARRANTY

EGO WARRANTY POLICY
Please visit the website egopowerplus.com for full terms and conditions of the EGO Warranty policy

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals