lightmaxx LIG0013620-000 Vega Shiggy Beam Wash User Manual

lightmaxx LIG0013620-000 Vega Shiggy Beam Wash

Product Information

• Product Name: Vega Shiggy Beam Wash
• Manufacturer: Lightmaxx
• Model Number: 02/2023 LIG0013620-000
• User Manual: Included
• Warranty: The warranty terms and conditions are provided by Music Store professional GmbH. Please refer to their website for more information.
• Website: www.musicstore.de
• Customer Support:
  • Tel: +49 221 8884-0
  • Fax: +49 221 8884-2500
  • Email: info@musicstore.de

Product Usage Instructions

1. Safety Precautions:

   • Before connecting the product, carefully read and understand the safety instructions provided in the user manual.
   • The lightning symbol warns the user about the risk of electric shock, indicating the presence of non-isolated voltage.
   • The exclamation mark symbol highlights important maintenance and operation instructions in the user manual.

2. Package Contents:
   The package includes the following items:

   • 1x Vega Shiggy Beam Wash
   • 1x User Manual
   • 1x Power Cable
   • 1x Omega Bracket

3. Installation:
   Please refer to the user manual for installation instructions.

4. Initial Setup:

   • Configure the DMX plug by adding a 120 Ohm 1/4W resistor between Pin 2 (DMX) and Pin 3 (DMX+) of the last fixture.
   • Refer to the user manual for detailed configuration instructions.

5. DMX Channel Definitions:
   Refer to the 16-channel definition table provided in the user manual for detailed information on each channel’s value and description.

6. Operating Modes:

   • Use Channel 19 to select the operating mode: Auto or Sound.
   • Refer to the user manual for specific channel values and their corresponding modes.
     Note: For further assistance or inquiries, please contact customer support using the provided contact information.

Safety Instructions

Please read before connection and operation!

WARNING: To prevent the risk of electrocution, do not open the device.

• Please leave all maintenance and repairs to a qualified service workshop or contact your distributor.
• The lightning flash symbol warns the user about non-insulated current and the risk of electrocution.
• The exclamation mark symbol warns the user about important maintenance and operating inst-ructions in the manual.
• Intended for indoor use only.
• Read the manual.
• This symbol indicates the minimum distance to illuminated objects.
• Please recycle the packaging correctly to protect the environment.
• Occasionally a new product may cause undesirable odours or even emit smoke for a short period of time. This reaction is normal and will disappear after a few minutes.
• The device is intended exclusively for us indoors (IP20)! Please use this device only in dry environments. Keep the device away from rain, moisture, direct heat and dust.
• To prevent condensation from forming in the device, please allow the device to adapt to the surrounding temperature before operating.
• Please position the device in a well ventilated area, beyond the reach of flammable materials or liquids.
• Do not block any ventilation openings, as it may cause over-heating.
• Please remove the power cable if the device is not operated for extended periods of time or maintenance is to be conducted.
• This device is designed to operate in environments with a maximum temperature of 40° Celsius.
• The installation of the device is not to be conducted by inexperienced persons and must adhere to the mechani-cal and electrical safety standards of the local law.
• In case of a damaged power cable, it must be replaced by an original replacement part from the manufacturer.
• Ensure that the supply voltage does not exceed the voltage
• capacity indicated on the housing of the device.
• In case of failure of the device, please contact the distri-bu-tor and stop all operations of the device immediately.
• The device must keep a minimum distance of one metre from flammable materials or liquids.
  WARNING: Do not look directly into the light source!Do not operate this device in the presence of persons suffering from epilepsy!

OVERHEAD INSTALLATION

• The installation must be performed exclusively by qua-lified personnel. Incorrect installation can cause serious injuries or da-mage. Note the load limits of the selected installation position.
• Ensure that during installation or dismantling/ maintenan-ce there are no unauthorized persons below the device.
• Manufacturer: MUSIC STORE professional GmbH, Istanbulstraße 22-26, 51103 Cologne, Germany

Congratulations on your new LightmaXX LED moving head!

• Thank you for choosing a Lightmaxx product. Thanks to effi cient development and economical production, Lightmaxx makes high-quality products at a fantastic price possible.
• Please read these operating instructions carefully to be informed about all functions of this product and keep them for future reference
  Have fun with your new product!
  Your Lightmaxx Team

Guarantee

The current general terms and conditions and guarantee conditions of Music Store professional GmbH apply.

• Can be viewed under: www.musicstore.de
• If you have any questions or suggestions, please contact us:
• Music Store professional GmbH Istanbulstr. 22-26 51103 Köln
• Managing Director: Michael Sauer WEEE-Reg.-Nr. DE 41617453

Scope of Delivery

• 1x VEGA Shiggy Beam Wash
• 1x Omega bracket
• 1x Power cable
• 1x User Manual

Intended use

• The LightmaXX Vector Spot 150 product was designed for generating electronic LED lighting effect. Incorrect use of the product is considered improper and can lead to per-sonal injury or property damage. Damage resulting from improper use is not liable.
• It must be ensured that the device is operated exclusively by trained and competent users who are in full possession of their mental, physical and sensory abilities. The use by other persons is only permitted under the supervision or guidance of a person responsible for their safety.

Safety instructions

• DANGER! (For Babies and Children)

  • Wrapping, plastic foils and other packaging material must be properly stored or disposed of. It should be kept out of the reach of babies and children due to the risk of suffocation.
  • Ensure that children never use the device unattended! Also make sure that children do not remove any (small) parts from the device, as they could suffocate if swallowed!

• DANGER! (electric shock due to high voltages in the device)

  • Do not remove the housing. There are no serviceable parts in the unit. Inside the device there are components which are under high electrical voltage.
  • The device must not be used if damage or the absence of components, protecti-ve devices or housing parts is noticed!

• DANGER! (electric shock caused by short circuit)

  • Modifi cations to the mains cable or the mains plug are prohibited.
  • Failure to do so may result in fi re or death hazard due to an electric shock!

• Warning! ( High light intensity – eye injuries)
  Looking directly into the light source results in eye injuries!

• Warning! (Epilepsy)
  Stroboscopic effects (fl ashes of light) can cause seizures of epilepsy in some people. Accordingly sensitive people are to be warned and should avoid a look at the corresponding effects.

• Warning! (Fire Hazard)
  Make sure that the device is not exposed to any direct heat source and is used away from open fi re. Never block or cover ventilation slots or the device itself.

• Note! (Operating conditions)
  Due to its structural characteristics, the device is designed for indoor use. Do not expose the device to rain, moisture or liquids, as this can cause damage. Vibrations, dirt or sunlight can also lead to damage, avoid them!

• Warning! (Power Supply)

  • Make sure that the device voltage matches your local mains voltage. It is strongly recommended to protect your mains socket with a residual current circuit breaker (RCD).
  • If you do not use your device for a longer period of time, disconnect the device from the mains to minimize dangers. The same applies to thunderstorms or fl oods, etc.

Installation

• Always check the device for damage before use. Use the original packaging or suitable transport or storage packaging to protect the product optimally from infl uences such as dust or moisture, etc. when not in use.

• The device can be installed either standing or hanging. The mounting must always be done on a solid, approved support or an appropriate surface. Use the opening of the brackets to attach the device. Always create a second, separate safeguard for the device, e.g. by means of a safety wire.

• All work on the device (e.g. installation) should always be carried out from a stable and approved platform. Make sure that the area below you is closed off.

• Please note that the use of this device with a dimmer is not possible!

  • Warning! (Risk of injury from falling)
    It must be ensured that the device complies with all legal standards and re- gulations in the respective country of use. Ensure that the device is always secured by a second mounting cable (e.g. Safety).

  • Warning! (Overheating)
    The maximum permissible ambient temperature of this device is 40° C. Ensure that the unit is always adequately ventilated.

Operation

All connections of the device should be made before switching on. Use only high-quality cables that are as short as possible for the connections.

DMX mode:
Connect the DMX input of your device to the DMX output of your DMX controller, your DMX software or the DMX output of a device already in your DMX chain. Always use DMX cable with a 110 Ohm resistor for this connection. Address the device according to your DMX confi guration. The following tables show the respective DMX modes of the individual devices with the corresponding values and functions.

Static, Auto or Sound mode:
The device contains automatic programs that run according to fi xed schemas (Au) or are recalled via the built-in microphone to match the music (Au). The selection of the respective mode takes place via the menu directly on the device.

CHANNEL

Operating mode auto or sound

The device contains automatic programs that run according to fi xed schemes (Auto) or are retrieved via the built-in microphone to match the music (sound). The respective mode is selected via the menu directly on the device.

Connections and operating element

1. Led-Lense
2. Display
3. Menu Buttons
4. Power input
5. DMX input(3 pole)
6. DMX output(3 pole)

Menu structure in details

Specifications

• Power Output 70 Watt
• Mains voltage 240V 50/60Hz
• LED Source Beam:1×10 Watt RGBW LED, Wash
• DMX Channels 17 channel/23 channel
• Movement Pan/Tilt X-axis: 540°, Y-axis endrolstation
• Beaming angle Beam 3°, Wash 25°
• Control mode DMX 512, Master-Slave, Autorun, Sound 2 Light
• Programme 8 Intern, Sound 2 Light per DMX
• Display LED Display
• Dimensions 325 x 250 x 270mm
• Weight 2,5kg

Troubleshooting:

Warning! (Fault during data transmission)

• Never connect the DMX input or output to audio devices such as power amplifi ers or mixing consoles!

• DMX cables enable interference-free operation and the highest possible transmission reliability of signal data. Do not use microphone cables.

• The following overview is intended as an aid for troubleshooting. If you are unsure, contact the manufacturer, the dealer or appropriate specialist personnel. Never open the device by yourself!

• No Function
  Check the network connection and its fuse.

• No Reaction in DMX Mode

  • Check the cable connections
  • If available, try an alternative DMX controller

• No Reaction from Remote Control

  • Change the battery in your remote control
  • Make sure that the IR transmitter and receiver are within a short and clear distance of each other.

Cleaning

Regular cleaning of the device from dirt and dust increases the shelf life of the product. Always disconnect the unit from the power supply while cleaning it. Optical lenses should be cleaned with a dry microfi ber cloth. This also optimises the light output. Never clean the device with water! Ventilation grilles and openings should always be free of dust and dirt. Compressed air sprays are ideal for this application.

Environmental Safety

Music Store professional GmbH always endeavours to reduce the burden of packaging to a minimum. The use of environmentally friendly and recyclable materials is always of fundamental importance. Please recycle the packaging after use.

• Disposal of packaging:
  Ensure that paper packaging, plastic material, etc. are recycled separately. Observe the labels and the corresponding regulations.

• Disposal of batteries:
  Batteries should not be thrown away! Please dispose of batteries in accordance with offi cial regulations.

• Disposal of your old device:

  • This device is subject to the WEEE directive (Waste Electrical and Electronic Equipment) in its currently valid form. The device must not be disposed of with normal household waste.
  • The device is disposed of via an approved disposal company or your local waste disposal centre. The regulations valid in your country must be observed!

References

• MUSIC STORE - Online Shop für Musikinstrumente - Deutschland | MUSIC STORE professional

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>