lightmaXX LIG0016820-000 VEGA Silent PAR III Complete User Manual
- June 13, 2024
- lightmaxx
Table of Contents
VEGA Silent PAR III Complete
LIG0016820-000 VEGA Silent PAR III Complete
Important safety instructions!
Please read before connection!
DANGER! (Electrical shock due to high voltages in the device)
The housing must not be removed! There are no parts to be maintained in the
device.
Inside the unit there are components which are under high electrical voltage.
Before each use, check the device for damage or the absence of components,
protective devices or housing parts. If this is the case, the device must not
be used!
Leave maintenance and repair work to a qualified service workshop or contact
your dealer. In the case of a malfunction of the device, operation must also
be stopped immediately until the device has been repaired by a specialist!
DANGER! (Electric shock due to short circuit)
Modifications to the power cord or plug are prohibited. If the power cord is
damaged, it must be replaced immediately with an original spare part from the
manufacturer. Failure to do so may result in fire or death due to electric
shock!
DANGER! (For babies and children)
Dispose of or store any packaging material properly! Packaging material must
be kept out of the reach of babies and children due to the risk of
suffocation.
Ensure that children never use the appliance unattended! In addition, make
sure that children do not remove (small) parts from the device, as they could
suffocate by swallowing parts!
WARNING! (High light intensity – eye injuries)
A direct view into the light source is absolutely to be omitted!
WARNING! (Epilepsy)
Stroboscopic effects (flashes of light) can trigger seizures of epilepsy in
some people.
Accordingly sensitive people should be warned and should not be in the
vicinity of such devices.
Hint! (Fire hazard due to overheating)
The maximum permissible ambient temperature of this device is 40°C.
Ensure that the unit is placed in a well-ventilated location away from direct
heat sources, naked flames, combustible materials, and liquids. A minimum
distance of 1 m is required.
Do not tape or cover the ventilation slots of the unit.
Hint! (Operating conditions)
Due to its structural characteristics, the device is designed for indoor
operation (IP20).
Never expose the device to rain, moisture or liquids as this may cause damage.
Vibrations, dust or sunlight can also cause damage, avoid them!
Hint! (Power supply)
It is essential that you check that the device voltage matches your local
mains voltage. It is highly recommended that you fuse your mains socket with a
residual current circuit breaker (FI).
If you do not use your device for a longer period of time or carry out
maintenance work, disconnect the device from the mains in order to minimize
danger. The same applies to storm conditions such as thunderstorms, floods,
etc.
Hint! (Error during data transmission)
Never connect the DMX input or output to audio devices such as power
amplifiers or mixing consoles!
DMX cables enable trouble-free operation and the highest possible transmission
reliability of signal data. Do not use microphone cables!
Hint! (Condensation)
To avoid condensation in the unit, the unit should adapt to the ambient
temperature before commissioning.
Hint! (Unwanted odours)
A new product can sometimes lead to unwanted odours. This reaction is normal
and disappears after a few minutes.
Symbols on device and packaging:
The lightning flash symbol warns the user of uninsulated voltages and the
risk of electric shock.
The exclamation mark symbol draws the user’s attention to important maintains
and operating instructions in the manual.
This symbol defines the minimum distance of the object to be illuminated.
**** Read the manual
Please read and follow the warnings and recommendations carefully to ensure
safe and trouble-free use.
Installation
Be sure to check the unit for damage before use. Use the original packaging or
a suitable transport or storage packaging to protect the product from dust,
moisture, etc. when not in use.
The unit can be installed either upright or suspended. The device must always
be attached to a solid, approved carrier or a suitable surface. Note the load
limit of the selected installation position (e.g. for tripods).
The opening of the bracket must be used to fasten the device. Always provide a
second, independent safety backup for the device, e.g. with a safety cable.
Work on the device (e.g. assembly) should always be carried out from a stable
and permissible platform. Make sure that the area below you is closed off.
WARNING! (Risk of injury due to falling down)
Improper installation can cause considerable injury and damage!
The installation of the device should always be carried out by experienced
personnel and must be carried out in compliance with the mechanical and
electrical safety regulations in your country.
Please note that it is not possible to use this device with a dimmer!
Congratulations on your new lightmaXX VEGA Silent PAR III Complete
Thank you for choosing a lightmaXX product. Through efficient development and
economical production, lightmaXX enables high quality products at a fantastic
price.
Please read the instruction manual carefully to learn about all the features
of this product and keep it for future use.
Have fun with your new product!
Your lightmaXX Team
Guarantee
The current general terms and guarantee conditions of the Music Store
professional GmbH apply.
You can view it at: www.musicstore.de
If you have any questions or suggestions, please contact us:
Music Store professional GmbH
Istanbulstr. 22-26
51103 Cologne
Managing Director: Michael Sauer
WEEE-Reg.-No. DE 41617453
Tel: +49 221 8884-0
Fax: +49 221 8884-2500
info@musicstore.de
Scope of delivery
| Content | Quantity |
|---|---|
| VEGA Silent PAR III | 1 |
| Power Cord | 1 |
| Mounting Bracket | 1 |
| Manual | 1 |
Intended use
The lightmaXX VEGA Silent PAR III Complete was designed for use as an
electronic LED lighting effect. The device may only be used for this purpose
and in accordance with the operating instructions. Other purposes as well as
operation under other operating conditions are expressly not intended and can
lead to damage to property or personal injury! No liability is assumed for
damage resulting from improper use.
It must be ensured that the device is operated exclusively by trained and
competent users who are in full possession of their mental, physical and
sensory abilities. The use of other persons is expressly only permitted at the
request of a person responsible for their safety, who instructs or supervises
the use.
Set up
All connections of the device should be made before switching on. Only use
high-quality cables that are as short as possible for the connections.
Configuration of the DMX connector:
Resistance 120 ohm // ¼ w between pin 2 (DMX-) and pin 3 (DMX+) oft he last
fixture.
Operating mode DMX:
Connect the DMX input of your device to the DMX output of your DMX controller,
your DMX software or the DMX output of a device already in your DMX line.
Always use a DMX cable with a 110 Ohm resistor for this connection. Address
the device according to your DMX configuration. The following table shows the
respective DMX modes of the individual devices with the corresponding values
and functions:
10 Channel Mode:
| Channel | Value | Function |
|---|---|---|
| 1 | 000-255 | Master Dimmer (0-100%) |
| 2 | 000-255 | Strobe Effect (Speed: slow to fast) |
| 3 | 000-255 | Macro function |
| 4 | 000-255 | Macro function Setting Speed |
| 5 | 000-255 | Red Dimmer (0-100%) |
| 6 | 000-255 | Green Dimmer (0-100%) |
| 7 | 000-255 | Blue Dimmer ( 0-100%) |
| 8 | 000-255 | White Dimmer (0-100%) |
| 9 | 000-255 | Amber Dimmer ( 0-100%) |
| 10 | 000-255 | UV Dimmer |
Static, Auto or Sound mode
The device contains automatic programs that run according to fixed schemes
(Auto) or are recalled via the built-in microphone to match the music (Sound).
The selection of the respective mode takes place via the menu directly on the
device.
If you connect several devices of the same type via DMX, they can be
controlled simultaneously via the master device. To do this, set the desired
function “Master” on the first device of the line, the other devices of the
series must now be set as “Slave”. Now the first device of the line gives the
function to all other devices and all devices run simultaneously.
Operation
Start:
Connect the device to the mains and wait a few seconds until it is ready for
operation.
Connections and controls
| Nr. | Bezeichnung | Nr. | Bezeichnung |
|---|---|---|---|
| 1 | Locking Screw | 6 | Operating keys |
| 2 | Mounting Bracket | 7 | DMX Input (3-pole) |
| 3 | LED Lenses | 8 | DMX Output (3-pole) |
| 4 | Fan | 9 | Power Supply |
| 5 | Display | 10 | Power Output |
Menu:
Navigation in the menu is via the four menu buttons below the display. Use the
“Mode” button to activate the menu, navigate via the “Up” and “Down” buttons.
A corresponding selection is confirmed with the “Enter” key.
The menu structure in detail:
| Menu | Value | Function |
|---|---|---|
| d | 000-512 | Setting DMX address |
| Auxx | Au01 Au02 Au03 Au04 Au05 Au06 Au07 Au08 Au09 Au10 So01 So02 | Color |
Mixing 1
Color Mixing 2
Color Mixing 3
Color Mixing 4
Color Mixing 5
Color Mixing 6
Color Mixing 7
3 Color Jump Change Jump Change Gradual Change
Sound Control Jump Change Sound Control Strobe
St00| St00 St01-16| Auto Master without Strobe Auto Master Strobe Speed
( from slow to fast)
SP| 00-16| Auto Master Au08/09/10 Speed ( from slow to fast)
r| 000-255| Red Dimmer (0-100%)
G| 000-255| Green Dimmer (0-100%)
B| 000-255| Blue Dimmer (0-100%)
W| 000-255| White Dimmer (0-100%)
A| 000-255| Amber Dimmer (0-100%)
uv| 000-255| UV Dimmer (0-100%)
Specifications
| Model | VEGA Silent PAR III Complete |
|---|---|
| Power supply | AC110-240V,50/60HZ |
| Power consumption | 280 Watt |
| LEDs | 14 x 18 Watt |
| Color Mixing | RGBWAUV |
(Red – Green – Blue – White – Amber – UV)
Beam angle| 45°
Operating Modes| Auto, Sound Mode, Master/Slave, DMX
Features| Static Colors, Color Change, Color Fade, Dimmer and Strobe
Effect
DMX Channels| 10
Connections| DMX-In-/Output (3-pole) Power Con In-/Output
Dimensions without Bracket (L x W x H)| 29 x 29 x 25 mm
Weight| 3,5 kg
Troubleshooting
The following overview serves as an aid for quick troubleshooting. If you are unsure, contact the manufacturer, the dealer or the corresponding specialist personnel. Never open the device on your own!
| Symptom | Troubleshooting |
|---|---|
| No function | Check the mains connection and the fuse |
| No reaction in DMX mode | Check the cable connections |
Check your DMX address setting
If available, try an alternative DMX controller
No reaction in remote mode
| Change the battery in your remote control
Ensure that the IR transmitter and receiver are at close and clear distances
from each other
If the specified corrections have not led to success, please contact our
service staff. The contact details can be found at
www.musicstore.de
Cleaning:
Regular cleaning of the device from dirt and dust increases the shelf life of
the product. Always disconnect the device from the power supply before
cleaning it! Never clean the appliance wet!
Optical lenses should be cleaned with a dry microfiber cloth to optimize light
output. Ventilation grilles and openings should always be cleaned of dust and
dirt. Suitable compressed air sprays are recommended for this application.
Environmental protection:
The company MUSIC STORE professional GmbH always strives to reduce the burden
of packaging to a minimum. The use of environmentally friendly and recyclable
materials is of fundamental importance to us. Please dispose of and recycle
the packaging components after use properly.
Disposal of packaging:
Ensure that paper packaging, plastic materials, etc. are separately recycled.
Observe the corresponding disposal instructions on the packaging.
Disposal of batteries:
Batteries do not belong in the garbage! Please keep batteries in accordance
with the official collection points or disposal stations in accordance with
the specifications.
Disposal of your old device:
Do not dispose of the device with household waste! This device is subject to
the WEEE Directive (Waste Electrical and Electronic Equipment) in its
currently valid version.
The device will be disposed of by an approved waste disposal company or your
local waste disposal office. The regulations valid in your country must be
observed!
Manufacturer: MUSIC STORE professional GmbH,
Istanbulstraße 22-26,
51103 Cologne, Germany
MS ID:
LIG0016820-000
02/2023
References
- MUSIC STORE - Online Shop für Musikinstrumente - Deutschland | MUSIC STORE professional
- Music Store Online-Shop für Musikinstrumente | MUSIC STORE professional
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>