lightmaXX LIG0016541-000 Cannon Shot FX FOUR User Manual
- June 13, 2024
- lightmaxx
Table of Contents
- Symbols on device and packaging
- Installation
- Scope of delivery
- Intended use
- Set up
- Operating mode DMX
- 6 Channel Mode
- Remote Control
- Wireless controller pairing
- Operation
- Connections and controls
- Menu
- Specifications
- Troubleshooting
- Cleaning
- Environmental protection
- Customer Support
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
lightmaXX LIG0016541-000 Cannon Shot FX FOUR
Important safety instructions! Please read before connection!
DANGER! (Electrical shock due to high voltages in the device)
The housing must not be removed! There are no parts to be maintained in the
device. Inside the unit there are components which are under high electrical
voltage.
Before each use, check the device for damage or the absence of components, protective devices or housing parts. If this is the case, the device must not be used!
Leave maintenance and repair work to a qualified service workshop or contact your dealer. In the case of a malfunction of the device, operation must also be stopped immediately until the device has been repaired by a specialist!
DANGER! (Electric shock due to short circuit)
Modifications to the power cord or plug are prohibited. If the power cord is
damaged, it must be replaced immediately with an original spare part from the
manufacturer. Failure to do so may result in fire or death due to electric
shock!
DANGER! (For babies and children)
Dispose of or store any packaging material properly! Packaging material must
be kept out of the reach of babies and children due to the risk of
suffocation.
Ensure that children never use the appliance unattended! In addition, make sure that children do not remove (small) parts from the device, as they could suffocate by swallowing parts!
WARNING! (High light intensity – eye injuries)
A direct view into the light source is absolutely to be omitted!
WARNING!
The lightmaXX Cannon Shot FX FOUR only works with approved electric confetti
and streamer cannons and can be operated with either 50 or 80 cm cannons. All
pre-filled cannons are for single use only.
The electric cannons contain pressure vessels to blow the confetti or streamers out of the cannon at high pressure. The shooting area must always be kept clear.
Attention: Never shoot confetti directly at people, animals or objects
Hint! (Fire hazard due to
overheating)
The maximum permissible ambient temperature of this device is 40°C
Ensure that the unit is placed in a well-ventilated location away from direct heat sources, naked flames, combustible materials, and liquids. A minimum distance of 1 m is required.
Do not tape or cover the ventilation slots of the unit.
Hint! (Operating
conditions)
Due to its structural characteristics, the device is designed for indoor
operation (IP20). Never expose the device to rain, moisture or liquids as this
may cause damage.
Vibrations, dust or sunlight can also cause damage, avoid them!
Hint! (Power supply)
It is essential that you check that the device voltage matches your local
mains voltage. It is highly recommended that you fuse your mains socket with a
residual current circuit breaker (FI).
If you do not use your device for a longer period of time or carry out maintenance work, disconnect the device from the mains in order to minimize danger. The same applies to storm conditions such as thunderstorms, floods, etc.
Hint! (Error during data
transmission)
Never connect the DMX input or output to audio devices such as power
amplifiers or mixing consoles!
DMX cables enable trouble-free operation and the highest possible transmission reliability of signal data. Do not use microphone cables!
Hint! (Condensation)
To avoid condensation in the unit, the unit should adapt to the ambient temperature before commissioning.
Hint! (Unwanted odours)
A new product can sometimes lead to unwanted odours. This reaction is normal
and disappears after a few minutes.
Symbols on device and packaging
The lightning flash symbol warns the user of uninsulated voltages and the risk
of electric shock.
The exclamation mark symbol draws the user’s attention to important maintains
and operating instructions in the manual.
Only suitable for indoor use.
This symbol defines the minimum distance of the object to be illuminated.
Read the manual
Please read and follow the warnings and recommendations carefully to ensure safe and trouble-free use.
Installation
Be sure to check the unit for damage before use. Use the original packaging or a suitable transport or storage packaging to protect the product from dust, moisture, etc. when not in use.
The unit can be installed either upright or suspended. The device must always
be attached to a solid, approved carrier or a suitable surface. Note the load
limit of the selected installation position (e.g. for tripods).
The opening of the bracket must be used to fasten the device. Always provide a
second, independent safety backup for the device, e.g. with a safety cable.
Work on the device (e.g. assembly) should always be carried out from a stable and permissible platform. Make sure that the area below you is closed off.
WARNING! (Risk of injury due to falling down)
Improper installation can cause considerable injury and damage! The
installation of the device should always be carried out by experienced
personnel and must be carried out in compliance with the mechanical and
electrical safety regulations in your country.
Please note that it is not possible to use this device with a dimmer!
Congratulations on your new lightmaXX Cannon Shot FX FOUR
Thank you for choosing a lightmaXX product. Through efficient development and economical production, lightmaXX enables high quality products at a fantastic price.
Please read the instruction manual carefully to learn about all the features of this product and keep it for future use.
Have fun with your new product!
Your lightmaXX Team
Scope of delivery
Content | Quantity |
---|---|
lightmaXX Cannon Shot FX FOUR | 1 |
Power Cord | 1 |
Remote control | 1 |
Receiver | 1 |
Manual | 1 |
Intended use
The lightmaXX Cannon Shot FX FOUR was designed the use for the distribution of confetti. The device may only be used for this purpose and in accordance with the operating instructions. Other purposes as well as operation under other operating conditions are expressly not intended and can lead to damage to property or personal injury! No liability is assumed for damage resulting from improper use.
It must be ensured that the device is operated exclusively by trained and competent users who are in full possession of their mental, physical and sensory abilities. The use of other persons is expressly only permitted at the request of a person responsible for their safety, who instructs or supervises the use.
Set up
All connections of the device should be made before switching on. Only use high-quality cables that are as short as possible for the connections.
Configuration of the DMX connector:
Resistance 120 ohm // ¼ w between pin 2 (DMX-) and pin 3 (DMX+) oft he last fixture.
Operating mode DMX
Connect the DMX input of your device to the DMX output of your DMX controller, your DMX software or the DMX output of a device already in your DMX line. Always use a DMX cable with a 110 Ohm resistor for this connection. Address the device according to your DMX configuration. The following table shows the respective DMX modes of the individual devices with the corresponding values and functions:
6 Channel Mode
Channel | Value | Function |
---|---|---|
1 | 000-010 | |
011-255 | No Function |
Safe/Master
2| 000-010
011-255| No Function
trigger head 1
3| 000-010
011-255| No Function
trigger head 2
4| 000-010
011-255| No Function
trigger head 3
5| 000-010
011-255| No Function
trigger head 4
6| 000-010
011-255| No Function
trigger all heads
Remote Control
The device can be remote controlled using the remote control included in the scope of delivery. The respective functions can be performed using the various program selection or color keys.
The remote control has 4 buttons: press the “A”, “B” or “C” buttons to trigger one gun barrel at a time and the “D” button to trigger all gun barrels.
Press and hold the controller buttons to trigger shots.
(At least 1 second for single shot, 2 seconds for double/multiple shots
Wireless controller pairing
One machine can pair with up to 5 controllers.
Here are steps to pair with new controllers:
Step 1: Power on machine, disconnect DMX connection. Connect receiver to the 5-pin socket. Press MENU key to navigate to [r—], and set it to [r on] to enable wireless control.
Step 2: Press MENU key to navigate to DMX address menu [d—], now long press MENU key, machine will enter wireless controller registering mode, and display [rEg-]/[rEg.-], it will last 10 seconds.
Step 3 : Within 10 seconds, press any buttons of new controllers, the display will change to [rEgx], the last digit x is the number of controllers currently registered, it can be 1-5.
Step 4 : after 10 seconds, display will show [donE], registering mode exit, session finish.
Note 1: In a session, registering the sixth controller will be treated as a new first one, and make the former 5 registered controllers become unregistered!
Note 2 : In a new session, if new controller being registered, the controllers registered in last session would become unregistered, so to add new controllers, you need to register old controllers in a same session too.
Operation
First, place the Cannon Shot FX FOUR on a flat and stable surface.
Then insert the electric cannon into one of the cannon holders.
Next, secure the electric cannon in the cannon holder by tightening the cannon screw on the side.
Once the electric cannon has been mounted in the cannon tube, the desired firing direction can be set.
To do this, turn the adjustment screw on the side of the lightmaXX Cannon Shot FX FOUR to move the cannon tube to the desired position.
Now carefully insert the firing plug of the electric cannon into the plug connector on the top of the machine. The plug has a recess so that it can only be inserted in one position.
Hints:
Plug in the ignition plug ONLY when the red LED on the top next to the Cannon connector is NOT lit!
When the red LED is lit, the confetti cannon can be triggered as soon as it is supplied with power.
Caution: Never shoot confetti directly at people, animals or objects
Connections and controls
No. | Designation | No. | Designation |
---|---|---|---|
1 | Cannon screw nut | 7 | DMX-Output (3-pol) |
2 | Richt screw nut | 8 | Display and Menu buttons |
3 | Cannon tube | 9 | Power Twist Input |
4 | Cannon connector | 10 | Safety |
5 | LED indicator | 11 | Receiver connection |
6 | DMX-Input (3-pol) | 12 | On-/off switch |
Menu
Navigation in the menu is via the four menu buttons below the display. Use the “Menu” button to activate the menu, navigate via the “Up” and “Down” buttons.
The menu structure in detail:
Display | Value | Funktion |
---|---|---|
d— | 001-512 | Setting DMX-address |
r on/ r off | Enable/Disable wireless control |
Specifications
Model | Cannon Shot FX FOUR |
---|---|
Power supply | AC110-240V, 50/60Hz |
Power consumption | 150 Watts |
Operating modes | DMX, Remote Control |
DMX channels | 6 |
Connections | Power Twist, DMX In- and Output (3-pol) |
Dimensions (L x W x H) | 268 x 260 x 200 mm |
Weight | 7,5 kg |
Troubleshooting
The following overview serves as an aid for quick troubleshooting. If you are unsure, contact the manufacturer, the dealer or the corresponding specialist personnel. Never open the device on your own!
Symptom | Troubleshooting |
---|---|
No function | Check the mains connection and the fuse |
No reaction in DMX mode
| Check the cable connections
Check your DMX address setting
If available, try an alternative DMX controller
No reaction in remote mode
| Change the battery in your remote control
Ensure that the IR transmitter and receiver are at close and clear distances
from each other
If the specified corrections have not led to success, please contact our service staff. The contact details can be found at www.musicstore.de
Cleaning
Regular cleaning of the device from dirt and dust increases the shelf life of the product. Always disconnect the device from the power supply before cleaning it! Never clean the appliance wet! Optical lenses should be cleaned with a dry microfiber cloth to optimize light output. Ventilation grilles and openings should always be cleaned of dust and dirt. Suitable compressed air sprays are recommended for this application.
Environmental protection
The company MUSIC STORE professional GmbH always strives to reduce the burden of packaging to a minimum. The use of environmentally friendly and recyclable materials is of fundamental importance to us. Please dispose of and recycle the packaging components after use properly.
Disposal of packaging:
Ensure that paper packaging, plastic materials, etc. are separately recycled.
Observe the corresponding disposal instructions on the packaging.
Disposal of batteries:
Batteries do not belong in the garbage! Please keep batteries in accordance
with the official collection points or disposal stations in accordance with
the specifications.
Disposal of your old device:
Do not dispose of the device with household waste! This device is subject to
the WEEE Directive (Waste Electrical and Electronic Equipment) in its
currently valid version.
The device will be disposed of by an approved waste disposal company or your local waste disposal office. The regulations valid in your country must be observed.
Manufacturer: MUSIC STORE professional GmbH,
Istanbulstraße 22-26,
51103 Cologne, Germany
Guarantee:
The current general terms and guarantee conditions of the Music Store professional GmbH apply. You can view it at: www.musicstore.de
If you have any questions or suggestions, please contact us:
Bei Fragen und Anregungen wenden Sie sich bitte an:
Music Store professional GmbH
Istanbulstr. 22-26
51103 Cologne
Managing Director: Michael Sauer WEEE-Reg.-No. DE 41617453
Customer Support
Tel: +49 221 8884-0
Fax: +49 221 8884-2500
info@musicstore.de
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>