lightmaXX LIG0016335-000 Cannon Shot FX TWO User Manual

June 13, 2024
lightmaxx

lightmaXX LIG0016335-000 Cannon Shot FX TWO

lightmaXX LIG0016335-000 Cannon Shot FX TW-product

Product Information

The lightmaXX Cannon Shot FX TWO is a lighting device with multiple functions. It can be operated using DMX or a remote control. The device has a power input of AC110-240V, 50/60Hz and consumes 150 watts of power. It features a DMX input and output (3-pin) and is equipped with 4 Power Twist connectors. The dimensions of the device are 268 x 220 x 200 mm and it weighs 4.6 kg.

INTRODUCTION

Hint! (Fire hazard due to overheating)
The maximum permissible ambient temperature of this device is 40°C.
Ensure that the unit is placed in a well-ventilated location away from direct heat sources, naked flames, combustible materials, and liquids. A minimum distance of 1 m is required.
Do not tape or cover the ventilation slots of the unit.

Hint! (Operating conditions)
Due to its structural characteristics, the device is designed for indoor operation (IP20). Never expose the device to rain, moisture or liquids as this may cause damage.
Vibrations, dust or sunlight can also cause damage, avoid them!

Hint! (Power supply)
It is essential that you check that the device voltage matches your local mains voltage. It is highly recommended that you fuse your mains socket with a residual current circuit breaker (FI).
If you do not use your device for a longer period of time or carry out maintenance work, disconnect the device from the mains in order to minimize danger. The same applies to storm conditions such as thunderstorms, floods, etc.
Hint! (Error during data transmission)

Never connect the DMX input or output to audio devices such as power amplifiers or mixing consoles!
DMX cables enable trouble-free operation and the highest possible transmission reliability of signal data. Do not use microphone cables!

Hint! (Condensation)
To avoid condensation in the unit, the unit should adapt to the ambient temperature before commissioning.

Hint! (Unwanted odours)
A new product can sometimes lead to unwanted odours. This reaction is normal and disappears after a few minutes.

Symbols on device and packaging

  • The lightning flash symbol warns the user of uninsulated voltages and the risk of electric shock.
  • The exclamation mark symbol draws the user’s attention to important maintains and operating instructions in the manual.
  • Only suitable for indoor use.
  • This symbol defines the minimum distance of the object to be illuminated.
  • Read the manual

Please read and follow the warnings and recommendations carefully to ensure safe and trouble-free use.

Installation

Be sure to check the unit for damage before use. Use the original packaging or a suitable transport or storage packaging to protect the product from dust, moisture, etc. when not in use.
The unit can be installed either upright or suspended. The device must always be attached to a solid, approved carrier or a suitable surface. Note the load limit of the selected installation position (e.g. for tripods).
The opening of the bracket must be used to fasten the device. Always provide a second, independent safety backup for the device, e.g. with a safety cable.
Work on the device (e.g. assembly) should always be carried out from a stable and permissible platform. Make sure that the area below you is closed off.

WARNING! (Risk of injury due to falling down)
Improper installation can cause considerable injury and damage!
The installation of the device should always be carried out by experienced personnel and must be carried out in compliance with the mechanical and electrical safety regulations in your country.

Please note that it is not possible to use this device with a dimmer!

Congratulations on your new lightmaXX Cannon Shot FX TWO

Thank you for choosing a lightmaXX product. Through efficient development and economical production, lightmaXX enables high quality products at a fantastic price.
Please read the instruction manual carefully to learn about all the features of this

product and keep it for future use.
Have fun with your new product!

Your lightmaXX Team

Guarantee

  • The current general terms and guarantee conditions of the Music Store professional GmbH apply.
  • You can view it at: www.musicstore.de
  • If you have any questions or suggestions, please contact us:
  • Music Store professional GmbH
  • Istanbulstr. 22-26  51103 Cologne
  • Managing Director : Michael Sauer
  • WEEE-Reg.-No. DE 41617453
  • Tel : +49 221 8884-0
  • Fax : +49 221 8884-2500 info@musicstore.de

Intended use

Scope of delivery

Content Quantity
lightmaXX Cannon Shot FX TWO 1
Power Cord 1
Remote control 1
Receiver 1
Manual 1

The lightmaXX Cannon Shot FX TWO was designed the use for the distribution of confetti. The device may only be used for this purpose and in accordance with the operating instructions. Other purposes as well as operation under other operating conditions are expressly not intended and can lead to damage to property or personal injury! No liability is assumed for damage resulting from improper use.

It must be ensured that the device is operated exclusively by trained and competent users who are in full possession of their mental, physical and sensory abilities. The use of other persons is expressly only permitted at the request of a person responsible for their safety, who instructs or supervises the use.

Set up
All connections of the device should be made before switching on. Only use high-quality cables that are as short as possible for the connections.

Configuration of the DMX connector

lightmaXX LIG0016335-000 Cannon Shot FX TWO02

Resistance 120 ohm // ¼ w between pin 2 (DMX-) and pin 3 (DMX+) oft he last fixture.

Operating mode DMX

Connect the DMX input of your device to the DMX output of your DMX controller, your DMX software or the DMX output of a device already in your DMX line. Always use a DMX cable with a 110 Ohm resistor for this connection. Address the device according to your DMX configuration. The following table shows the respective DMX modes of the individual devices with the corresponding values and functions:

Channel Mode

Channel| Value|

Function

---|---|---
1| 000-010

011-255

| No Function Safe/Master
2| 000-010

011-255

| No Function

trigger head 1

3| 000-010

011-255

| No Function trigger head 2
4| 000-010

011-255

| No Function

trigger all heads 1&2

Remote Control

The device can be remote controlled using the remote control included in the scope of delivery. The respective functions can be performed using the various program selection or color keys.
The remote control has 2 buttons: press the “A” button to trigger one cannon tube and the “B” button to trigger both cannon tubes.
Press and hold the controller buttons to trigger shots.

(At least 1 second for single shot, 2 seconds for double/multiple shots.

lightmaXX LIG0016335-000 Cannon Shot FX TWO3

Wireless controller pairing

One machine can pair with up to 5 controllers.
Here are steps to pair with new controllers:

Step 1 : Power on machine, disconnect DMX connection. Connect receiver to the 5-pin socket. Press MENU key to navigate to [r—], and set it to [r on] to enable wireless control.

Step 2: Press MENU key to navigate to DMX address menu [d—], now long press MENU key, machine will enter wireless controller registering mode, and display [rEg-]/[rEg.-], it will last 10 seconds.

Step 3: Within 10 seconds, press any buttons of new controllers, the display will change to
[rEgx], the last digit x is the number of controllers currently registered, it can be 1-5.

Step 4: after 10 seconds, display will show [donE], registering mode exit, session finish.
Note1 : In a session, registering the sixth controller will be treated as a new first one, and make the former 5 registered controllers become unregistered!

Note2: In a new session, if new controller being registered, the controllers registered in last session would become unregistered, so to add new controllers, you need to register old controllers in a same session too.

Operation
First, place the Cannon Shot FX TWO on a flat and stable surface.
Then insert the electric cannon into one of the cannon holders.
Next, secure the electric cannon in the cannon holder by tightening the cannon screw on the side.
Once the electric cannon has been mounted in the cannon tube, the desired firing direction can be set.
To do this, turn the adjustment screw on the side of the lightmaXX Cannon Shot FX TWO to move the cannon tube to the desired position.
Now carefully insert the firing plug of the electric cannon into the plug connector on the top of the machine. The plug has a recess so that it can only be inserted in one position.

Hints
Plug in the ignition plug ONLY when the red LED on the top next to the Cannon connector is NOT lit!
When the red LED is lit, the confetti cannon can be triggered as soon as it is supplied with power.
Caution: Never shoot confetti directly at people, animals or objects

Connections and controls

lightmaXX LIG0016335-000 Cannon Shot FX TWO4

No.| Designation| No.|

Designation

---|---|---|---
1| Cannon screw nut| 7| DMX-Output (3-pol)
2| Richt screw nut| 8| Display and Menu buttons
3| Cannon tube| 9| Power Twist Input
4| Cannon connector| 10| Safety
5| LED indicator| 11| Receiver connection
6| DMX-Input (3-pol)| 12| On-/offswitch

Menu
Navigation in the menu is via the four menu buttons below the display. Use the “Menu” button to activate the menu, navigate via the “Up” and “Down” buttons.
The menu structure in detail

Display| Value|

Funktion

---|---|---
d—| 001-512| Setting DMX-address
r on/ r off| | Enable/Disable wireless control

Specifications

Model|

Cannon Shot FX TWO

---|---
Power supply| AC110-240V, 50/60Hz
Power consumption| 150 Watts
Operating modes| DMX, Remote Control
DMX channels| 4
Connections| Power Twist, DMX In- and Output (3-pol)
Dimensions (L x W x H)| 268 x 220 x 200 mm
Weight| 4,6 kg

Troubleshooting

The following overview serves as an aid for quick troubleshooting. If you are unsure, contact the manufacturer, the dealer or the corresponding specialist personnel. Never open the device on your own!

Symptom|

Troubleshooting

---|---
No function| Check the mains connection and the fuse
No reaction in DMX mode| Check the cable connections
Check your DMX address setting
If available, try an alternative DMX controller
No reaction in remote mode| Change the battery in your remote control
Ensure that the IR transmitter and receiver are at close and clear distances from each other

If the specified corrections have not led to success, please contact our service staff. The contact details can be found at www.musicstore.de

Cleaning
Regular cleaning of the device from dirt and dust increases the shelf life of the product. Always disconnect the device from the power supply before cleaning it! Never clean the appliance wet! Optical lenses should be cleaned with a dry microfiber cloth to optimize light output. Ventilation grilles and openings should always be cleaned of dust and dirt. Suitable compressed air sprays are recommended for this application.

Environmental protection
The company MUSIC STORE professional GmbH always strives to reduce the burden of packaging to a minimum. The use of environmentally friendly and recyclable materials is of fundamental importance to us. Please dispose of and recycle the packaging components after use properly.

Disposal of packaging
Ensure that paper packaging, plastic materials, etc. are separately recycled. Observe the corresponding disposal instructions on the packaging.

Disposal of batteries
Batteries do not belong in the garbage! Please keep batteries in accordance with the official collection points or disposal stations in accordance with the specifications.

Disposal of your old device
Do not dispose of the device with household waste! This device is subject to the WEEE Directive (Waste Electrical and Electronic Equipment) in its currently valid version.
The device will be disposed of by an approved waste disposal company or your local waste disposal office. The regulations valid in your country must be observed.

Hersteller: MUSIC STORE professional GmbH, Istanbulstraße 22-26,
51103 Köln, Deutschland

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals