Razor 210623 Light-Up Electric Scooters Owner’s Manual
- June 5, 2024
- Razor
Table of Contents
Razor 210623 Light-Up Electric Scooters
NOTE : The unit must be traveling at least 3 mph (5 km/h) before the motor will engage. Kick to start to at least 3 mph (5 km/h) while applying the throttle to engage the motor.
OWNER’S MANUAL
Read and understand this entire manual before allowing the child to use
this product! For assistance contact Razor. DO NOT RETURN TO THE STORE.
NOTE: Manual illustrations are for demonstration purposes only.
Illustrations may not reflect the exact appearance of the actual product.
Specifications are subject to change without notice.
Please have your product along with the 19-character product I.D. code with
you before contacting Razor for warranty assistance and/or replacement parts.
Product I.D. Code:
SAFETY WARNINGS
WARNING: Riding an electric scooter does present potential risks and caution is required. Like any riding product, an electric scooter has inherent hazards associated with its use (for example, falling off or riding it into a hazardous situation). Like any riding product, electric scooters can and are intended to move and it is therefore, of course, possible to lose control or otherwise get into dangerous situations. Both children, and adults responsible for supervising them, must recognize that if such things occur, a rider can be seriously injured or die even when using safety equipment and other precautions. RIDE AT YOUR OWN RISK AND USE COMMON SENSE.
WARNING: PARENTAL AND ADULT RESPONSIBILITY AND SUPERVISION IS NECESSARY : Because products, like electric scooters, can and do present potential hazards plainly associated with their use, it is well recognized THE NEED FOR EXERCISE OF PARENTAL RESPONSIBILITY IN SELECTING RIDING PRODUCTS APPROPRIATE TO THE AGE OF A CHILD, OR PARENTAL SUPERVISION IN SITUATIONS IN WHICH CHILDREN OF VARIOUS AGES MAY HAVE ACCESS TO THE SAME RIDING PRODUCTS, IS IMPORTANT. Not every product is appropriate for every age or size of child, and different age recommendations are found within this category of product which are intended to reflect the nature of the hazards and the expected mental or physical ability, or both, of a child to cope with the hazards.
WARNING: NOT FOR RIDERS UNDER AGE 8 OR HEAVIER THAN 110 LB (50 KG). DO NOT
EXCEED THE WEIGHT LIMIT OF 110 lb
(50 kg) – including backpacks and other items that might be carried. Exceeding
the weight limit could injure the rider and damage the electric scooter. Rider
weight alone also does not necessarily mean a person’s size is appropriate to
fit or maintain control of the electric scooter. Keep this product away from
small children and remember that this product is intended for use only by
persons who are, at a minimum, completely comfortable and competent while
operating the product. Razor recommends that children under the age of 8 not
be permitted to use this product. This recommendation is based not just on age
or weight or height; it reflects consideration of expected maturity and skills
as well as physical size. The recommended rider age of 8 years or older is
only an estimate and can be affected by the rider’s size, weight, or skills –
not every rider 8 years old or older will be suited to the product. Certainly,
any rider unable to fit comfortably on the electric scooter should not attempt
to ride it, but a parent’s decision to allow his or her child to ride this
product should be based on the child’s maturity, skill, and ability to follow
rules. Razor emphasizes that adults are strongly advised not to disregard
Razor’s recommendations or permit young children to ride the electric scooter.
Keep this product away from small children and remember that it is intended
for use only by persons who are, at a minimum, completely comfortable and
competent while operating. Persons with any mental or physical conditions that
may make them susceptible to injury, impair their physical dexterity or mental
capabilities to recognize, understand, and follow safety instructions and to
be able to understand the hazards inherent in the use of any ride-on product,
should not use or be permitted to use products inappropriate for their
abilities. Persons with heart conditions, head, back or neck ailments (or
prior surgeries to these areas of the body), or pregnant women, should be
cautioned not to operate such products.
DO NOT EXCEED THE WEIGHT LIMIT OF 110 lb (50 kg). Rider weight does not
necessarily mean a person’s size is appropriate to fit or maintain control of
the electric scooter.
CHECK AND MAINTAIN PRODUCT CONDITIONS
Before use, check to confirm that covers and guards are in place and in
serviceable condition. Check that the wheels are free of flat spots from wear.
The product should be maintained and repaired in accordance with the
manufacturer’s specifications, using only the manufacturer’s authorized
replacement parts, and should not be modified from the manufacturer’s original
design and configuration.
ACCEPTABLE RIDING PRACTICES AND CONDITIONS
Always check and obey any local laws or regulations which may affect the
locations where the electric scooter may be used. Keep safely away from cars
and motor vehicle traffic at all times. Only use where allowed and with
caution. Do not activate the foot-controlled power system unless you are on
the electric scooter and in a safe, outdoor environment suitable for riding.
The electric scooter must be moving at least 3 mph (5 km/h) before the motor
will engage. Once the foot-controlled power system is activated the electric
scooter will move forward. The normal powered top speed of this product will
be approximately 7.5 mph (12 km/h), which can be affected by conditions, such
as rider weight, inclines and battery charge level. Avoid excessive speeds
that can be associated with downhill rides. Maintain a hold on the handlebars
at all times. Ride defensively. Watch out for potential obstacles that could
catch your wheel or force you to swerve suddenly or lose control. Be careful
to avoid pedestrians, skaters, skateboards, scooters, bikes, children or
animals who may enter your path, and respect the rights and property of
others.
The electric scooter is intended for use on flat, dry surfaces, such as
pavement or level ground, without loose debris, such as sand, leaves, rocks or
gravel. Wet, slick, bumpy, uneven or rough surfaces may impair traction and
contribute to possible accidents. Do not ride your product in mud, ice,
puddles or water. Watch out for potential obstacles that could catch your
wheel or force you to swerve suddenly or lose control. Avoid sharp bumps,
drainage grates, and sudden surface changes. Do not attempt or do stunts or
tricks. The electric scooter is not made to withstand abuse from misuse, such
as jumping, curb grinding or any other type of stunts. Racing, stunt riding,
or other maneuvers also enhance risk of loss of control, or may cause
uncontrolled rider actions or reactions.
Never allow more than one person at a time to ride the product.
- Do not ride at night or when visibility is limited.
- Never use near steps or swimming pools.
- Do not allow hands, feet, hair, body parts, clothing, or similar articles to come in contact with moving parts or wheels while the motor is engaged.
- Do not touch electric motor when in use or immediately after riding.
- Never use headphones or a cell phone to talk or text when riding.
- Never hitch a ride with a vehicle.
- Do not ride your product in wet or icy weather and never immerse in water, as the electrical and drive components could be damaged by water or create other possibly unsafe conditions. Never risk damaging surfaces, such as carpet or flooring, by use of an electric scooter indoors.
PROPER RIDING ATTIRE
Always wear proper protective equipment, such as an approved safety helmet
(with chin strap securely buckled), elbow pads, and kneepads. A helmet may be
legally required by local law or regulation in your area. A long-sleeved
shirt, and long pants are recommended. Always wear shoes and keep shoelaces
tied and out of the way of the wheels and motor. Never ride barefooted or in
sandals.
USING THE CHARGER
The charger supplied with the product should be regularly examined for damage
to the cord, plug, enclosure and other parts. In the event of such damage, the
product must not be charged until the charger has been repaired or replaced.
Use only with the recommended charger. Use caution when charging. The charger
is not a toy. Charger should be operated by an adult. Do not operate charger
near flammable materials. Unplug charger and disconnect from product when not
in use. Always disconnect from the charger prior to wiping down and cleaning
your product with damp cloth.
FAILURE TO USE COMMON SENSE AND HEED THE ABOVE WARNINGS FURTHER INCREASES
RISK OF SERIOUS INJURY. USE AT YOUR OWN RISK AND WITH APPROPRIATE AND SERIOUS
ATTENTION TO SAFE OPERATION. USE CAUTION.
Need Help? Visit our website for product support, a list of authorized service centers in the US and customer service contact information at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service contact information is listed at the back of this manual.
BEFORE YOU BEGIN
Remove contents from box. Remove the separators that protect the components
from damage during shipping. Inspect the contents of the box for scratches in
the paint, dents that may have occurred during shipping. Because your scooter
was assembled and packed at the factory, there should not be any problems,
even if the box has a few scars or dents.
THIS UNIT DOES NOT HAVE A POWER SWITCH. LIGHTS WILL TURN OFF AUTOMATICALLY.
UNIT IS ALWAYS ON STANDBY MODE WHEN NOT BEING RIDDEN.
Estimated Assembly and Set-Up Time
- Allow up to 5 minutes for assembly, not including initial charge time.
- Allow up to 4 hours for charge (see page 5 for charging information).
Charger
Note: Charger design may vary from one shown
WARNING: DO NOT USE NON-RAZOR PRODUCTS WITH YOUR SCOOTER.
Razor scooters have been built to certain Razor design specifications. The
original equipment supplied at the time of sale was selected on the basis of
its compatibility with the frame, fork and all other parts. Certain
aftermarket products may not be compatible and will void the warranty.
Note: Electric scooter must be moving at least 3 mph (5 km/h) while
applying the foot-controlled power system to engage the motor.
Product ID Locations:(See locations to the left)
- Front Left Side of Deck
- Charger
- UPC Side of Box (Not Shown)
Required Tool
5 mm Allen Wrench (included)
Box Contents
- Electric Scooter
- Charger
- Owner’s Manual
- 5 mm Allen Wrench
HAESSEADLMIBNLEY AND SET-UP
Attaching the Handlebars
Required Tool: 5 mm Allen Wrench (included)
- Using a 5 mm Allen wrench, loosen the bolt from the collar clamp.
- With a twisting motion, push and twist to slide the handlebars onto the fork.
- With the front wheel pointed straight ahead and the handlebars square to the front wheel, tighten bolt on the clamp as shown with a 5 mm Allen wrench.
Tighten securely.
WARNING:
Check handgrips and end caps regularly for wear or damage, as they are
designed to aid in gripping handlebars and to provide some protection against
possible impact. Replace immediately if worn, torn, damaged, or missing.
WARNING:
Do not attempt to thread the handlebar into the front fork thread. Tighten
collar clamp securely.
WARNING:
Failure to properly install and tighten the collar clamp may cause the rider
to lose control and fall. If you are having difficulty understanding these
instructions, please contact Razor Customer Service for assistance.
HCEHAADRLGIINNEG THE BATTERY
Your electric scooter may not have a fully charged battery; therefore you must charge the battery prior to use. Be sure to charge the battery in a clean, dry location away from direct sunlight, flames or sparks.
- Initial charge time: 4 hours.
- Recharge time: up to 3 hours, even if the light turns green. Recommended maximum charging time is 24 hours.
- Always charge the battery immediately after riding.
- Fully charge battery before storing for extended periods of time.
- Unplug charger from the wall outlet when not in use.
- Failure to recharge battery periodically may result in a battery that will not accept a charge.
- Make sure the lights are OFF when product is not in use.
- Run time: Up to 30 minutes of continuous ride time. Run time may vary depending on riding conditions, rider weight, climate, and/or proper maintenance.
- Constant starting and stopping may shorten ride time.
- Battery life can vary depending on proper maintenance and usage of the product.
- Do not charge at or below 32°F (0°C).
Charger
(Note: Charger design may vary from one shown)
-
Plug the charger plug into wall outlet. The light on the charger should be green.
Note: If green light (LED) does not turn on, try a different outlet. -
Note: Make sure lights are OFF. Plug the charger into the charger port. The light on the charger should turn red during charging. The light will turn green again when charging is complete.
WARNING: Use ONLY with the recommended charger. Batteries are only to be
charged under adult supervision. The charger is not a toy. Always disconnect
the charger before wiping down and/or cleaning the electric scooter with a
damp cloth. The charger supplied with the electric scooter should be regularly
examined for damage to the cord, plug, enclosure and other parts. In the event
of such damage, the electric scooter must not be charged until it has been
repaired or replaced. Chargers have built-in overcharge protection to prevent
battery from being overcharged.
Wall outlet – Green (stand by)
Wall outlet and product – Red (charging)
Wall outlet and product – Green (charged)
Note: Continue charging product even if light turns green prior to 3
hours.
WARNING: Battery charge can deplete over time. Periodically recharge
battery when not in use.
PRE-RIDE CHECKLIST
Brake
Check the brake for proper function. When you step on the rear-fender brake,
the brake should provide positive braking action. When you apply the brake
with the foot-controlled power system engaged, the brake cut-off switch should
cut power to the motor.
Wheels
Periodically inspect the wheels for excessive wear.
Frame, Fork and Handlebars
Check for cracks or broken connections. Although broken frames are rare, it is
possible for an aggressive rider to run into a curb or object and wreck, bend
or break a frame. Get in the habit of inspecting your scooter on a regular
basis.
Hardware/Loose Parts
Before every ride, check all parts, such as nuts, bolts, fasteners, etc., to
ensure they are secure and assembled correctly. There should not be any
unusual rattles or sounds from loose parts or broken components. If the
product is damaged, do not ride. Reference “Safety Warnings” on pages 1 and 2
of this manual.
Safety Gear
Always wear proper protective equipment, such as an approved safety helmet
(with chin strap securely buckled), elbow pads, and kneepads. A helmet may be
legally required by local law or regulation in your area. A long-sleeved shirt
and long pants are recommended. Always wear shoes and keep shoelaces tied and
out of the way of the wheels and motor. NEVER RIDE BAREFOOTED OR IN
SANDALS.
Laws and Regulations
Always check and obey any local laws or regulations.
Insurance
Do not assume that your existing insurance policies necessarily provide
coverage for product use. Check with your insurance company for information
regarding insurance.
Storage
Prolonged exposure to UV rays, rain and the elements may damage the enclosure
materials, store indoors when not in use.
USAGEHEADLINE
How to Ride
Standing in the center of the deck engages the foot-controlled power system.
Do not activate the foot-controlled power system (A) (pressure sensor is
located under deck grip tape) unless you are on the electric scooter and in a
safe, outdoor environment suitable for riding.
Get on the scooter and place both hands on the handlebars. Kick to start (B).
Note: LED deck lights will activate when the power system is pressed. The
light-up front wheel will activate when the product is in motion.
How to Stop
For controlled stops, apply the brake by putting pressure on the rear-fender brake. Razor recommends that you practice applying the brake at various speeds and in an open area free from obstructions before riding your scooter around others.
Note: Pressure on the power system (center of the deck) will activate the power of the electric scooter. However, the motor is designed not to engage until the electric scooter is moving at least 3 mph (5 km/h) while engaging the foot-controlled power system.
Note: As an additional safety feature, the scooter is designed to cut
power to the motor when brake is applied.
Note: Motor will re-engage, (without having to kick to start), if brake
is released and a foot-controlled power system is applied before scooter has
slowed down to under 3 mph (5 km/h).
Note: Practice riding only in wide-open areas clear from curbs, parking
blocks and other obstacles. Impacting the wheels against any hard surface can
damage the wheels. Wheels are not covered under the limited warranty.
RHEEPADAILRINE AND MAINTENANCE
WARNING: Risk of fire–no user-serviceable parts.
Cleaning Your Scooter
Wipe with a damp cloth to remove dirt and dust. Do not use industrial cleaners or solvents as they may damage the surfaces. Do not use alcohol, alcohol-based or ammonia-based cleaners as they may damage or dissolve the plastic components or soften the decals or decal adhesive.
Battery Care and Disposal
- Do not store in freezing or below-freezing temperatures. To properly maintain your battery and ensure maximum battery life, carefully read the “Charging the Battery” section on page 5 of this owner’s manual.
- Battery pack should not be disassembled, crushed, punctured, opened or otherwise mutilated.
Disposal : Your electric scooter uses a lithium-ion battery pack which
must be recycled or disposed of in an environmentally safe manner. Do not
dispose of a battery pack in a fire. The battery pack may explode.
Do not dispose of a battery pack in your regular household trash. The
incineration, land filling or mixing of batteries with household trash is
prohibited by law in most areas. Return exhausted batteries to a federal or
state approved lithium-ion battery recycler.
Charger
The charger supplied with the electric scooter should be regularly examined
for damage to the cord, plug, enclosure and other parts and in the event of
such damage, the product must not be charged until it has been repaired or
replaced.
Use ONLY with the recommended charger.
Not intended for use at elevations greater than 2000 m above sea level.
Wheels and Bearings
Under normal circumstances and conditions, Razor wheels and wheel bearings are maintenance free. Nonetheless, it is the responsibility of the owner or guardian to periodically inspect the wheels for wear and tear, the axle for proper tightness, and bearings for side-to-side play, and loose parts. When a wheel or wheel bearing develops play, this is an indication of excess wear and replacement is necessary. Replace immediately with only genuine Razor wheels. Worn wheels/bearings are considered normal wear-and-tear and are not covered by the Razor Warranty. Wheels other than genuine Razor wheels may not be compatible with your Razor scooter. The use of anything other than genuine Razor replacement parts may affect your safety and will void your warranty.
Repair Centers
For a list of authorized Razor repair centers:
- Check online at www.razor.com.
- Additional Customer Service contact information is listed on the back of this manual.
Recycling Lithium-ion Batteries : Lithium-ion batteries are recyclable. You can help preserve our environment by returning your used rechargeable batteries to the collection and recycling location nearest you.
In the US and Canada only:
For more information regarding recycling of rechargeable batteries, call toll
free at 1-800-822-8837, or visit
http://www.call2recycle.org
Caution: Do not handle damaged lithium-ion batteries.
WARNING: Wheelies and other stunt-type riding reduces your ability to maneuver and control your scooter. Take the necessary precautions, such as wearing appropriate protective gear and practice in an area safe for stunt riding and free from obstructions.
FCC COMPLIANCE
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications to this product not expressly approved by Razor USA LLC, could void the user’s authority to operate the equipment.
WARRANTY
Razor Limited Warranty
The manufacturer warranties this product to be free of manufacturing defects
for a period of 90 days from date of purchase. This Limited Warranty does not
cover normal wear and tear, wheel, or any damage, failure or loss caused by
improper assembly, maintenance, storage or use of the electric scooter.
This Limited Warranty will be void if the product is ever:
- used in a manner other than for recreation or transportation;
- modified in any way;
- rented.
The manufacturer is not liable for incidental or consequential loss or damage due directly or indirectly to the use of this product. Razor does not offer an extended warranty. If you have purchased an extended warranty, it must be honored by the store at which it was purchased. For your records, save your original sales receipt with this manual and write the serial number below.
CUSTOMER SERVICE CONTACT INFORMATION
Need Help? Visit our website for product support, a list of authorized service centers in the US and customer service contact information at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service contact information is listed below:
AMERICAS
Razor USA LLC
P.O. Box 3610 Cerritos, CA 90703 USA
+1 866 467 2967 Monday – Friday
8:00 AM – 5:00 PM Pacific Time
customersupport@razorusa.com
UNITED KINGDOM AND IRELAND
Razor USA LLC (UK)
Unit 20
Hartnoll Business Centre
Post Hill, Tiverton
Devon EX16 4NG
UK
+44 (0) 120 267 2702
info@razoreu.com
Printed in China for Razor USA LLC.
References
- Call2Recycle | Leading the Charge For Battery Recycling
- Razor | Scooters and Ride-ons for the whole family
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>