lightmaXX LIG0014819-000 Vega 3 Way PRO Beam WASH FX User Manual

: June 13, 2024
: lightmaxx

Table of Contents

LIG0014819-000 Vega 3 Way PRO Beam WASH FX
OVERHEAD INSTALLATION
Safety instructions:
Installation:
Specifications:
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LIG0014819-000 Vega 3 Way PRO Beam WASH FX
User Manual

LIG0014819-000 Vega 3 Way PRO Beam WASH FX

Safety Instructions! Please read before connection and operation!
RISK OF ELECTRIC SHOCK. DO NOT OPEN!
WARNING: To prevent the risk of electrocution, do not open the device.
Please leave all maintenance and repairs to a qualiﬁed service workshop or contact your distributor.
The lightning ﬂ ash symbol warns the user about non-insulated current and the risk of electrocution.
The exclamation mark symbol warns the user about important maintenance and operating inst-ructions in the manual.
Intended for indoor use only.
Read the manual.
This symbol indicates the minimum distance to illuminated objects.

Please recycle the packaging correctly to protect the environment.
Occasionally a new product may cause undesirable odors or even emit smoke for a short period of time. This reaction is normal and will disappear after a few minutes.
The device is intended exclusively for us indoors (IP20)! Please use this device only in dry environments. Keep the device away from rain, moisture, direct heat and dust.
To prevent condensation from forming in the device, please allow the device to adapt to the surrounding temperature before operating.
Please position the device in a well ventilated area, beyond the reach of ﬂammable materials or liquids.
Do not block any ventilation openings, as it may cause over-heating.
Please remove the power cable if the device is not operated for extended periods of time or maintenance is to be conducted.
This device is designed to operate in environments with a maximum temperature of 40° Celsius.
The installation of the device is not to be conducted by inexperienced persons and must adhere to the mechanical and electrical safety standards of the local law.
In case of a damaged power cable, it must be replaced by an original replacement part from the manufacturer.
Ensure that the supply voltage does not exceed the voltage
capacity indicated on the housing of the device.
In case of failure of the device, please contact the distributor and stop all operations of the device immediately.
The device must keep a minimum distance of one meter from ﬂammable materials or liquids.

WARNING: Do not look directly into the light source! Do not operate this device in the presence of persons suffering from epilepsy!

OVERHEAD INSTALLATION

The installation must be performed exclusively by qualiﬁed personnel.
Incorrect installation can cause serious injuries or da-mage. Note the load limits of the selected installation position. Ensure that during installation or dismantling/ maintenance there are no unauthorized persons below the device.
Manufacturer: MUSIC STORE professional GmbH, Istanbulstraße 22-26, 51103 Köln, Germany
Congratulations on your new Lightmaxx Moving Head!
Thank you for choosing a Lightmaxx product. Thanks to efﬁcient development and economical production, Lightmaxx makes high-quality
products at a fantastic price possible.
Please read the operating instructions carefully to be informed about all functions of this LED system and keep it for future reference. Have fun with your new product! Your Lightmaxx Team Scope of Delivery:

Contents	Quantity
1x	Moving Head
1x	Power Cable
2x	Mounting Bracket
1x	Manual

Safety instructions:

DANGER! (For Babies and Children)
Wrapping, plastic foils and other packaging material must be properly stored or disposed of. It should be kept out of the reach of babies and children due to the risk of suffocation.
Ensure that children never use the device unattended! Also make sure that children do not remove any (small) parts from the device, as they could suffocate if swallowed!
DANGER! (electric shock due to high voltages in the device)
Do not remove the housing. There are no serviceable parts in the unit.
Inside the device there are components which are under high electrical voltage. The device must not be used if damage or the absence of components, protective devices or housing parts is noticed!
DANGER! (electric shock caused by short circuit)
Mode cations to the mains cable or the mains plug are prohibited. Failure to do so may result in ﬁ re or death hazard due to an electric shock!
Warning! ( High light intensity – eye injuries)
It is absolutely forbidden to look directly into the light source.
Warning! (Epilepsy)
Stroboscopic effects (ﬂashes of light) can cause seizures of epilepsy in some people. Accordingly sensitive people are to be warned and should avoid a look at the corresponding effects.
Warning! (Fire Hazard)
Make sure that the device is not exposed to any direct heat source and is used away from open ﬁ re. Never block or cover ventilation slots or the device itself.
Note! (Operating conditions)
Due to its structural characteristics, the device is designed for indoor use. Do not expose the device to rain, moisture or liquids, as this can cause damage. Vibrations, dirt or sunlight can also lead to damage, avoid them!
Warning! (Power Supply)
Make sure that the device voltage matches your local mains voltage. It is strongly recommended to protect your mains socket with a residual current circuit breaker (RCD).
If you do not use your device for a longer period of time, disconnect the device from the mains to minimize dangers. The same applies to thunderstorms or ﬂoods, etc.

Installation:

Always check the device for damage before use. Use the original packaging or suitable transport or storage packaging to protect the product optimally from inﬂ uences such as dust or moisture, etc. when not in use.
The device can be installed either standing or hanging. The mounting must always be done on a solid, approved support or an appropriate surface. Use the opening of the brackets to attach the device. Always create a second, separate safeguard for the device, e.g. by means of a safety wire. All work on the device (e.g. installation) should always be carried out from a stable and approved platform. Make sure that the area below you is closed off.
Please note that the use of this device with a dimmer is not possible!
Menu Function

menu (Color Display 2.4‘TFT–X8)

DMX Addressee| 001~512| |
**Operating Mode| DMX 17 Ch| |
DMX 10 Ch| |
** Auto| Perform Mode 1|
Perform Mode 2|
Perform Mode 3|
Perform Mode 4|
Perform Mode 5|
Perform Mode 6|
Perform Mode 7|
Perform Mode 8|
Sound| |
Master Audio| Perform Mode 1|
Perform Mode 2|
Perform Mode 3|
Perform Mode 4|
Perform Mode 5|
Perform Mode 6|
Perform Mode 7|
Perform Mode 8|
Master Sound| |
Slave| |
**Advanced Setting| Pan Reverse| |
Tilt Reverse| |
Display Reverse| |
Reset Motor| |
Factory Reset| |
Home Position| Password| Code = 018
| PAN| PAN = 000
| TILT| TILT = 000
| Focus| Focus = 000
| Effect Motor| EFFECT = 000
| Focus| DIMMER = 000
| | Red|
---|---|---|---
| Green|
| Blue|
| White|
| ** Language Setting|
| English
Mic Sensitive| 0|
**System Info| Current Time| Perform Mode 5|
Total Time| Perform Mode 6|
Current Mode| Perform Mode 7|
Temperature| Perform Mode 8|
Software Version| |
****Manual Control´**| Pan| PAN = 000|
Tilt| TILT = 000|
XY Speed| Move Speed = 000|
Focus| Focus = 000|
Effect Motor| Effect Motor = 000|
Dimmer| Dimmer = 000|
Strobe| Strobe = 000|
Red| Red = 000|
Green| Green = 000|
Blue| Blue = 000|
White| White = 000|

10 DMX Channel:

7 10CH 7	DMX Wert Function
1	000-255
000-255	X-Fine

2

| 000-255| Y
000-255| Y-Fine
000-255| XY SPEED
3| 000-255| Dimmer (0-100%)
4| 000-004| Shutter closed
005-250| Strobe effect slow to fast
251-255| Shutter open
5| 000-255| LED1 (0-100%)
6| 000-255| LED2 (0-100%)
7| 000-255| LED3 (0-100%)
8| 000-255| LED4 (0-100%)
9| 000-255| Focus (0-100%)
**** 10| 000-099| Effects Lens linear (0~60°)
100-133| Shake from Small to Big
134-194| Backward rotation from fast to slow
195-255| Forward rotation from slow to fast

17 DMX Channel:

17CH	DMX Wert Function
1	000-255
2	000-255
3	000-255
4	000-255
5	000-255
6	000-255
7	000-004
005-250	Strobe effect slow to fast
251-255	Shutter open
8	000-255
9	000-255
10	000-255
11	000-255
12	000-255
******** 13	000-099
100-133	Shake from Small to Big
134-255	Backward rotation from fast to slow
195-255	Forward rotation from slow to fast
14	000-007
008-015	Red
016-023	Amber
024-031	Yellow warm
032-039	Yellow
040-047	Green
048-055	Turquoise
056-063	Cyan
064-071	Blue
072-079	Lavender
080-087	Mauve
088-095	Magenta
096-103	Pink
104-111	White 3200K
112-119	White 5600K
120-127	White 7200K
128-191	Jump from slow to fast
192-255	Fade from slow to fast
15	000-009
---	---
010-039	Focus auto run 1
040-069	Focus auto run 2
070-099	Focus auto run 3
100-129	Focus auto run 4
130-159	Focus auto run 5
160-189	Focus auto run 6
190-219	Focus auto run 7
220-255	Focus auto run 8
**** 16	000-007
008-032	X/Y auto run 1
033-058	X/Y auto run 2
059-084	X/Y auto run 3
085-110	X/Y auto run 4
111-136	X/Y auto run 5
137-162	X/Y auto run 6
163-188	X/Y auto run 7
189-214	X/Y auto run 8
215-240	X/Y auto run 9
241-255	X/Y Sound Control
17	250-255

Specifications:

Power Supply	AC100-240V 50/60 Hz
Power Consumption	255 Watt(max)
Power Connection	IEC
DMX	3pin-XLR male/female
Extremely Long Life LED	50,000 Hours
LED	6x 40W high power RGBW LED
DMX Modes	10/17 Channels
Zoom	4-36°
Pan/Tilt	X:540°, Y:190°
Operating Modes	DMX512/Master-Slave/Auto run/Music
Display	LCD
Protection Class	IP 20
Weight	8,5Kg

Guarantee:
The current warranty terms and conditions of Music Store professional GmbH apply.
Can be viewed under: www.musicstore.de
If you have any questions or comments, please contact:

Music Store professional GmbH
Istanbulstr. 22-26
51103 Köln
Managing Director: Michael Sauer
WEEE-Reg.-Nr. DE 41617453
Tel: +49 221 8884-0
Fax: +49 221 8884-2500
info@musicstore.de