lightmaXX LS-4000 Pro Wind Up Stand User Manual

LS-4000 PRO
WIND-UP STAND LIG0009576-000
07/2020
User’s Manual

**Important safety instructions!

**

Please read before connection!
DANGER! (For babies and children)
Dispose of or store any packaging material properly! Packaging material must be kept out of the reach of babies and children due to the risk of suffocation.
Ensure that children never use the appliance unattended! In addition, make sure that children do not remove (small) parts from the device, as they could suffocate by swallowing parts!
Hint! (Operating conditions)
Due to its structural characteristics, the device is designed for indoor operation (IP20). Never expose the device to rain, moisture or liquids as this may cause damage.
Vibrations, dust or sunlight can also cause damage, avoid them!
If the load is too high, the stand can tip over and cause injury and cause damage to property. Never use the stand in the manner prescribed for the the maximum load capacity is exceeded. If the stand is placed on a soft or non- horizontal surface, it may tip over and cause injury and damage to property. Only place the stand on a level and solid surface . Pay attention to your fingers when mounting the stand, to avoid the risk of bruising.
Symbols on device and packaging:
The lightning flash symbol warns the user of uninsulated voltages and the risk of electric shock.
The exclamation mark symbol draws the user’s attention to important maintains and operating instructions in the manual.
Only suitable for indoor use.
This symbol defines the minimum distance of the object to be illuminated.
Read the manual
Please read and follow the warnings and recommendations carefully to ensure safe and trouble-free use.

Installation:

Be sure to check the unit for damage before use. Use the original packaging or a suitable transport or storage packaging to protect the product from dust, moisture, etc. when not in use.
The unit can be installed either upright or suspended. The device must always be attached to a solid, approved carrier or a suitable surface. Note the load limit of the selected installation position (e.g. for tripods).
The opening of the bracket must be used to fasten the device. Always provide a second, independent safety backup for the device, e.g. with a safety cable.
Work on the device (e.g. assembly) should always be carried out from a stable and permissible platform. Make sure that the area below you is closed off.
WARNING! (Risk of injury due to falling down)
Improper installation can cause considerable injury and damage!
The installation of the device should always be carried out by experienced personnel and must be carried out in compliance with the mechanical and electrical safety regulations in your country.
Please note that it is not possible to use this device with a dimmer!
Congratulations on your new lightmaXX LS-4000 PRO WIND-UP STAND!
Thank you for choosing a lightmaXX product. Through efficient development and economical production, lightmaXX enables high quality products at a fantastic price.
Please read the instruction manual carefully to learn about all the features of this product and keep it for future use.
Have fun with your new product!
Your lightmaXX Team
Guarantee:
The current general terms and guarantee conditions of the Music Store professional GmbH apply.
You can view it at: www.musicstore.de
If you have any questions or suggestions, please contact us:

Music Store professional GmbH
Istanbulstr. 22-26
51103 Köln
Geschäftsführer: Michael Sauer
WEEE-Reg.-Nr. DE 41617453
Tel: +49 221 8884-0
Fax: +49 221 8884-2500
info@musicstore.de

Scope of delivery:

Intended use:

The product lightmaXX LS-4000 PRO WIND-UP STAND functions as a wind up tripod for the recording of spotlights and effects. The device may only be used for this purpose and in accordance with the operating instructions. Other purposes as well as operation under other operating conditions are expressly not intended and can lead to damage to property or personal injury! No liability is assumed for damage resulting from improper use.
It must be ensured that the device is operated exclusively by trained and competent users who are in full possession of their mental, physical and sensory abilities. The use of other persons is expressly only permitted at the request of a person responsible for their safety, who instructs or supervises the use.

Commissioning:

Be sure to check the unit for damage before use. Use the original packaging or suitable transport or storage packaging to protect the product from dust, moisture, etc. when not in use.

Assembly of the stand:

To adjust the stand width, first loosen the locking screw (1) and pull out the fixing bolts (2).
Insert the fixing bolts at the desired height into the hole of the stand rod and tighten the fixing screw again.
Before using the stand, ensure that all locking screws and fixing bolts are secured.
If the stand is to be set up on a staircase or other uneven surface, first loosen the locking knob (3) and pull out the fixing bolt (4).
Pull out the tripod leg until the desired position is reached. Now reinsert the fixing bolt into the hole in the tripod leg and tighten the locking screw again.

Height adjustment:

Use the hand crank with cable pull to adjust the height of the mounted crossbar.

First loosen the fixing screw of the upper telescopic pole (5) and pull out the fixing bolt (6). Tighten the other fixing screw (7) to ensure a correct lifting sequence:
The upper smaller pole must be lifted first, followed by the larger pole!
Now turn the hand crank (8) clockwise to lift the upper pole. When the desired height is reached, insert the fixing bolt into the hole in the pole and tighten the fixing screw again.
Repeat the steps with the other pole: First loosen the fixing screw of the telescopic pole (7) and pull out the fixing bolt (9).
Turn the crank a little anti-clockwise to prevent the cable from carrying any load.

Disassembly of the stand:

To disassemble the stand, lower the height of the telescopic poles to the minimum height and make sure that all fixing bolts are inserted in the lowest position of the holes and all locking screws are tightened.
The steel cable must be correctly and completely rolled up to avoid crushing the fibres.
Then loosen the locking screw and pull out the fixing bolt.
Then pull the tripod legs back together to the tripod pole and insert the fixing bolt, then tighten the locking screw again.
The tripod can be transported in vertical or horizontal position.

Specifications:

Cleaning:

Regular cleaning of the device from dirt and dust increases the shelf life of the product. Always disconnect the device from the power supply before cleaning it! Never clean the appliance wet! Optical lenses should be cleaned with a dry microfiber cloth to optimize light output. Ventilation grilles and openings should always be cleaned of dust and dirt. Suitable compressed air sprays are recommended for this application.

Environmental protection:

The company MUSIC STORE professional GmbH always strives to reduce the burden of packaging to a minimum. The use of environmentally friendly and recyclable materials is of fundamental importance to us. Please dispose of and recycle the packaging components after use properly.
Disposal of packaging: Ensure that paper packaging, plastic materials, etc. are separately recycled. Observe the corresponding disposal instructions on the packaging.
Disposal of batteries: Batteries do not belong in the garbage! Please keep batteries in accordance with the official collection points or disposal stations in accordance with the specifications.
Disposal of your old device: Do not dispose of the device with household waste! This device is subject to the WEEE Directive (Waste Electrical and Electronic Equipment) in its currently valid version.
The device will be disposed of by an approved waste disposal company or your local waste disposal office. The regulations valid in your country must be observed

Hersteller: MUSIC STORE professional GmbH,
Istanbulstraße 22-26,
51103 Köln, Deutschland

Notes
……………………………………

MS ID: LIG0009576-000
07/2020

Product Service

CERTIFICATE

No. Z1A 17 11 57962 010

Holder of Certificate: Ningbo Soundking Electronics and Sound Co.,Ltd
Cheng Xin Road 818#,
Yinzhou Investment Industry Park
315104 Ningbo City, Zhejiang Prov.
PEOPLE’S REPUBLIC OF CHINA

https://sce.tuv-sud.com/sce?id=7K579

Certification Mark:
Product: Stand, Stop devices Stands for lightings
Tested according to: PPP 53303C:2017
AfPS GS 2014:01 PAK
The product meets the safety and health requirements of the German Product Safety Act section 20 to 22 ProdSG. The certification marks shown above can be affixed on the product. It is not permitted to alter the certification marks in any way. In addition the certificate holder must not transfer the certificate to third parties. This certificate is valid until the listed date, unless it is cancelled earlier. See also notes overleaf.

Test report no.: 702220514101-02
Valid until: 2022-12-06
Date, 2017-12-08

( Junjie Xu )

Product Service
CERTIFICATE
No. Z1A 17 11 57962 010
Model(s): DLC001, DLC002
Brand Name: SOUNDKING
Parameters:

Factory(ies): 57962

TUV SUD Product Service GmbH
Zertifizierstelle
RidlerstraGe 65
80339 Miinchen
Germany

Documents / Resources

| lightmaXX LS-4000 Pro Wind Up Stand [pdf] User Manual
LS-4000 Pro Wind Up Stand, LS-4000 Pro, Wind Up Stand, Up Stand, Stand
---|---
| lightmaXX LS-4000 PRO Wind Up Stand [pdf] User Manual
LS-4000 PRO Wind Up Stand, LS-4000 PRO, Wind Up Stand, Up Stand, Stand

References

• MUSIC STORE - Online Shop für Musikinstrumente - Deutschland | MUSIC STORE professional
• Music Store Online-Shop für Musikinstrumente | MUSIC STORE professional

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>