lightmaXX Vector Spot Zoom 2.0 Instruction Manual
- June 13, 2024
- lightmaxx
Table of Contents
Important safety instructions! Please read before connection!
DANGER! (Electrical shock due to high voltages in the device)
The housing must not be removed! There are no parts to be maintained in the
device. Inside the unit there are components which are under high electrical
voltage.
Before each use, check the device for damage or the absence of components,
protective devices or housing parts. If this is the case, the device must not
be used!
Leave maintenance and repair work to a qualified service workshop or contact
your dealer. In the case of a malfunction of the device, operation must also
be stopped immediately until the device has been repaired by a specialist!
DANGER! (Electric shock due to short circuit)
Modifications to the power cord or plug are prohibited. If the power cord is
damaged, it must be replaced immediately with an original spare part from the
manufacturer. Failure to do so may result in fire or death due to electric
shock!
DANGER! (For babies and children)
Dispose of or store any packaging material properly! Packaging material must
be kept out of the reach of babies and children due to the risk of
suffocation.
Ensure that children never use the appliance unattended! In addition, make
sure that children do not remove (small) parts from the device, as they could
suffocate by swallowing parts!
WARNING! (High light intensity – eye injuries)
A direct view into the light source is absolutely to be omitted!
WARNING! (Epilepsy)
Stroboscopic effects (flashes of light) can trigger seizures of epilepsy in
some people.
Accordingly sensitive people should be warned and should not be in the
vicinity of such devices.
Hint! (Fire hazard due to overheating)
The maximum permissible ambient temperature of this device is 40°C.
Ensure that the unit is placed in a well-ventilated location away from direct
heat sources, naked flames, combustible materials, and liquids. A minimum
distance of 1 m is required.
Do not tape or cover the ventilation slots of the unit.
Hint! (Operating conditions)
Due to its structural characteristics, the device is designed for indoor
operation (IP20).
Never expose the device to rain, moisture or liquids as this may cause damage.
Vibrations, dust or sunlight can also cause damage, avoid them!
Hint! (Power supply)
It is essential that you check that the device voltage matches your local
mains voltage. It is highly recommended that you fuse your mains socket with a
residual current circuit breaker (FI).
If you do not use your device for a longer period of time or carry out
maintenance work, disconnect the device from the mains in order to minimize
danger. The same applies to storm conditions such as thunderstorms, floods,
etc.
Hint! (Error during data transmission)
Never connect the DMX input or output to audio devices such as power
amplifiers or mixing consoles!
DMX cables enable trouble-free operation and the highest possible transmission
reliability of signal data. Do not use microphone cables!
Hint! (Condensation)
To avoid condensation in the unit, the unit should adapt to the ambient
temperature before commissioning.
Hint! (Unwanted odours)
A new product can sometimes lead to unwanted odours. This reaction is
normal and disappears after a few minutes.
Symbols on device and packaging:
The lightning flash symbol warns the user of uninsulated voltages and the risk
of electric shock.
The exclamation mark symbol draws the user’s attention to important maintains
and operating instructions in the manual.
Only suitable for indoor use.
This symbol defines the minimum distance of the object to be illuminated.
Read the manual
Please read and follow the warnings and recommendations carefully to ensure
safe and trouble-free use.
Installation:
Be sure to check the unit for damage before use. Use the original packaging or
a suitable transport or storage packaging to protect the product from dust,
moisture, etc. when not in use.
The unit can be installed either upright or suspended. The device must always
be attached to a solid, approved carrier or a suitable surface. Note the load
limit of the selected installation position (e.g. for tripods).
The opening of the bracket must be used to fasten the device. Always provide a
second, independent safety backup for the device, e.g. with a safety cable.
Work on the device (e.g. assembly) should always be carried out from a stable
and permissible platform. Make sure that the area below you is closed off.
WARNING! (Risk of injury due to falling down)
Improper installation can cause considerable injury and damage!
The installation of the device should always be carried out by experienced
personnel and must be carried out in compliance with the mechanical and
electrical safety regulations in your country.
Please note that it is not possible to use this device with a dimmer!
Congratulations on your new lightmaXX Vector Spot Zoom 2.0!
Thank you for choosing a lightmaXX product. Through efficient development and
economical production, lightmaXX enables high quality products at a fantastic
price.
Please read the instruction manual carefully to learn about all the features
of this product and keep it for future use.
Have fun with your new product!
Your lightmaXX Team
Guarantee:
The current general terms and guarantee conditions of the Music Store
professional GmbH apply.
You can view it at: www.musicstore.de
If you have any questions or suggestions, please contact us:
Music Store professional GmbH
Istanbulstr. 22-26
51103 Cologne
Managing Director: Michael Sauer
WEEE-Reg.-No. DE 41617453
Tel: +49 221 8884-0
Fax: +49 221 8884-2500
info@musicstore.de
Scope of delivery:
Content | Quantity |
---|---|
lightmaXX Vector SpoZoom 2.0 | 1 |
Omega Bracket | 2 |
Power cord | 1 |
Manual | 1 |
Intended use:
The lightmaXX Vector Spot Zoom 2.0 was designed for use as an electronic
LED lighting effect. The device may only be used for this purpose and in
accordance with the operating instructions. Other purposes as well as
operation under other operating conditions are expressly not intended and can
lead to damage to property or personal injury! No liability is assumed for
damage resulting from improper use.
It must be ensured that the device is operated exclusively by trained and
competent users who are in full possession of their mental, physical and
sensory abilities. The use of other persons is expressly only permitted at the
request of a person responsible for their safety, who instructs or supervises
the use.
Set up:
All connections of the device should be made before switching on. Only use
high-quality cables that are as short as possible for the connections.
Configuration oft he DMX connector:
3 pin:
Resistance 120 ohm // ¼ w between pin 2 (DMX-) and pin 3 (DMX+) oft he last fixture.
5 pin:
Operating mode DMX:
Connect the DMX input of your device to the DMX output of your DMX
controller, your DMX software or the DMX output of a device already in your
DMX line. Always use a DMX cable with a 110 Ohm resistor for this connection.
Address the device according to your DMX configuration.
The following table shows the respective DMX modes of the individual devices
with the corresponding values and functions:
6-Channel-Mode
Channel | Value | Function |
---|---|---|
1 | 000-255 | X |
2 | 000-255 | Y |
3 | 000-255 | Dimmer (0-100%) |
4 | 000-004 |
005-250
251-255| Shutter closed Strobe Effect
(Speed: slow to fast) Shutter open
5| 000-007
008-047
048-087
088-127
128-167
168-207
208-247
248-255| No function
Auto Play 1
Auto Play 2
Auto Play 3
Auto Play 4
Auto Play 5
Auto Play 6
Colour Gobo Sound Control
6| 000-007
008-032
033-058
059-084
085-110
111-136
137-162
163-188
189-214
215-240
241-255| No function
X/Y Auto Run 1
X/Y Auto Run 2
X/Y Auto Run 3
X/Y Auto Run 4
X/Y Auto Run 5
X/Y Auto Run 6
X/Y Auto Run 7
X/Y Auto Run 8
X/Y Auto Run 9
X/Y Sound Control
18-Channel-Mode
Channel | Value | Function |
---|---|---|
1 | 000-255 | Dimmer (0-100%) |
2 | 000-004 |
005-250
251-255| Shutter closed
Strobe Effect
(Speed: slow to fast) Shutter open
3| 000-255| X
4| 000-255| X-Fine
5| 000-255| Y
6| 000-255| Y-Fine
7| 000-255| XY Speed
8| 000-004
005-013
014-022
023-031
032-040
041-049
050-058
059-067
068-076
077-085
086-094
095-103
104-112
113-121
122-130
131-139
140-195
196-199
200-255| Open (White)
White/Colour 1
Colour 1
Colour 1/Colour 2
Colour 2
Colour 2/Colour 3
Colour 3
Colour 3/Colour 4
Colour 4
Colour 4/Colour 5
Colour 5
Colour 5/Colour 6
Colour 6
Colour 6/Colour 7
Colour 7
Open (White)
Forward Rainbow Effect (slow to fast)
Rotation Stop
Backward Rainbow Effect (slow to fast)
9| 000-007
008-017
018-027
028-037
038-047
048-057
058-067
068-077
078-087
088-097
098-107
108-117
118-127| Open (White)
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Gobo 1 Shake
Gobo 2 Shake
Gobo 3 Shake
Gobo 4 Shake
Gobo 5 Shake
10| 000-007
008-017
018-027
028-037
038-047
048-057
058-067
068-077
078-087
088-097
098-107
108-117
118-127
128-137
138-147
148-199
200-203
204-255| Open (White)
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Gobo 1 Shake
Gobo 2 Shake
Gobo 3 Shake
Gobo 4 Shake
Gobo 5 Shake
Gobo 6 Shake
Gobo 7 Shake
Forward Rainbow Effect (slow to fast)
Rotation Stop
Backward Rainbow Effects (slow to fast)
11| 000-007
008-129
130-133
134-255| Stop
Forward Gobo2 Rotation (slow to fast)
Stop
Backward Gobo2 Rotation (slow to fast)
12| 000-255| Focus
13| 000-255| Zoom
14| 000-007
008-099
100-130
131-255| Open (White)
Prism 1
Open (White)
Prism 2
15| 000-007
008-129
130-133
134-255| Stop
Forward Prism Rotation (fast to slow)
Stop
Backward Prism Rotation (slow to fast)
16| 000-007
008-047
048-087
088-127
128-167
168-207
208-247
248-255| No function
Auto Play 1
Auto Play 2
Auto Play 3
Auto Play 4
Auto Play 5
Auto Play 6
Colour Gobo Sound Control
17| 000-007
008-032
033-058| No function
X/Y Auto Run 1
X/Y Auto Run 2
18| 001-200
201-255| Speed
Reset (10S)
Static, Auto or Sound mode:
The device contains automatic programs that run according to fixed schemes
(Auto) or are recalled via the built-in microphone to match the music (Sound).
The selection of the respective mode takes place via the menu directly on the
device.
If you connect several devices of the same type via DMX, they can be
controlled simultaneously via the master device. To do this, set the desired
function “Master” on the first device of the line, the other devices of the
series must now be set as “Slave”. Now the first device of the line gives the
function to all other devices and all devices run simultaneously.
Operation:
Start:
Connect the device to the mains and wait a few seconds until it is ready for
operation.
Connections and controls:
No. | Designation | No | Designation |
---|---|---|---|
1 | Lens | 10 | Display |
2 | Projector head | 11 | Menu keys |
3 | Projector arm | 12 | Power suppy input (Power Twist) |
4 | Base | 13 | Power supply output (Power Twist) |
5 | Carrying handle | 14 | Fuse holder |
6 | Ventilation shaft | 15 | DMX Out (5-pole) |
7 | Rubber base | 16 | DMX In (5-pole) |
8 | DMX light | 17 | DMX Out (3-pole) |
9 | Error light | 18 | DMX In (3-pole) |
Menu:
Navigation in the menu is via the four menu buttons below the display. Use
the “Mode” button to activate the menu, navigate via the “Up” and “Down”
buttons. A corresponding selection is confirmed with the “Enter” key.
The menu structure in detail:
Display | Submenu | Value | Function |
---|---|---|---|
DMX Adress | 001-512 |
DMX 6 Ch
DMX 18 CH| Setting DMX-Adress
DMX 6 Channel Mode
DMX 18 Channel Mode
Operating mode| Auto| Perform Mode 1
Perform Mode 2
Perform Mode 3
Perform Mode 4
Perform Mode 5
Perform Mode 6
Perform Mode 7
Perform Mode 8| Program Auto Run
Sound| | Sound Control
Master Auto| Perform Mode 1
Perform Mode 2
Perform Mode 3
Perform Mode 4
Perform Mode 5
Perform Mode 6
Perform Mode 7
Perform Mode 8| Program Auto Run Master Mode
Master Sound| | Master Mode Sound Control
Slave| | Slave Control
Language
Setting| Chinese
English| | Menu language
Advanced
Setting| Pan Reverse
Tilt Reverse
Display Reverse
Reset Motor
Factory Reset
Home PositionPAN
TILT
Dimmer
Colour
fixed Gobo
Rotation Gobo
Focus
Zoom
Prism
Rotation Gobo Wheel
Mic Sensitive| Code=18
. =000
. =000
. =000
. =000
. =000
. =000
. =000
. =000
. =000
= 000| PAN Reverse
TILT Reverse
Display Reverse
Reset Motor
Factory Reset
Home PositionPAN
TILT
Dimmer
Colour
fixed Gobo
Rotation Gobo
Focus
Zoom
Prism
Rotation Gobo Wheel
Mic Sensitive
System Info| Current Time
Total Time
Current Mode
Temperature
Software Version| | Current Time
Total Time
Current Mode
Temperature
Software Version
Manual Control| PAN
TILT
PAN/TILT Speed
Dimmer
Strobe
Colour
fixed Gobo
Rotation Gobo
Rotation Gobo WheeFocus
Prism
Prism Wheel
Zoom| . =000
. =000
. =000
. =000
. =000
. =000
. =000
. =000
. =000
. =000
. =000
. =000
. =000| PAN
TILT
PAN/TILT Speed
Dimmer
Strobe
Colour
fixed Gobo
Gobo Rotation
Rotation Gobo Wheel
Focus
Prism
Prism Wheel
Zoom
Mounting options:
ATTENTION: Install the device outside the audience’s range.
It must be ensured that the intended mounting point has sufficient load-
bearing capacity. The projector’s suspension devices must be designed and
dimensioned to withstand 10 times the payload for 1 hour without permanent
damaging deformation.
The device must always be protected by a second independent fuse that complies
with the applicable regulations.
There must be no persons underneath the device when it is mounted or is
maintained.
The unit must be operated at least 0.5m from the nearest flammable surface.
Hanging installation may only be carried out by qualified personnel. The
permissible load-bearing capacity and the applicable regulations for event
technology must be observed. Under certain conditions, acceptance by experts
or institutions is necessary.
It must be ensured that the device is safely mounted before it is put into
operation.
If the unit is to be suspended from the ceiling or from high beams, etc., it
is always necessary to work with truss systems. The unit must never be fixed
in the room so that it can vibrate freely.
The device can be placed directly on the floor or in any position in the
trussing without changing its functional properties.
The unit is equipped with two quick-fit Omega suspension brackets. These are
screwed to the unit and provide a mounting hole for common clamps. When
mounting this device on a crossbar, make sure that the clamp is screwed to the
Omega suspension brackets using an M10 screw and nut. Insert the two quick-
release fasteners of the respective Omega support bracket into the openings
provided on the underside of the unit. Tighten the quick-release fasteners
clockwise until they stop.
Always secure the device with a suitable safety rope when it is mounted
overhead (mounting height >100 cm).
Only safety ropes and quick links in accordance with DIN 56927, shackles in
accordance with DIN EN 1677-1 and BGV C1 chain binders can be used. The safety
ropes, quick-connect links, shackles and chain binders must be sufficiently
dimensioned and correctly applied on the basis of the latest industrial safety
regulations (e.g. BGV C1, BGI 810-3).
Hook the quick-release link into the hole provided in the base plate. Guide
the safety rope over the crossbar or a secure fixing point. Hook the end into
the quick-release link and tighten the locking nut firmly.
The maximum drop distance must not exceed 20 cm.
A safety rope that has been subjected to a fall load or has been damaged may
no longer be used as a safety rope.
Specifications:
Model | lightmaxx Vector Spot Zoom 2.0 |
---|---|
Power supply | AC100-240V 50/60 Hz |
Total connected load | 260 Watt |
Modes of operation | Automatic Mode, DMX, Master/Slave, Sound Mode |
DMX Channels | 6 and 18 |
PAN Scan | 540° (16-bit), electrical correction |
TILT Scan | 270° (16-bit), electrical correction |
Colour Wheel | Colour Wheel, 7 types of color chips in one color wheel |
Static Gobo | 7 Gobos + open |
Rotation Gobo | 7 Gobos + open |
Effect Wheel | Two effects Prism, a six-line prism, one rotary five- round |
prism, bidirectional rotation.
Lens optical system mechanical focus, beam angle| 11°-25°
Dimmer| 0-100%
Lightning rate| 0-20 Hz
Prism| bidirectional rotation
Connections| DMX-In/Out (3-po1/5-pol) Power Twist-In/Out
Dimensions (LxWxH)| 328 x 220 x 482 mm
Weight| 12,5 Kg
The following overview serves as an aid for quick troubleshooting. If you are unsure, contact the manufacturer, the dealer or the corresponding specialist personnel. Never open the device on your own!
Symptom | Troubleshooting |
---|---|
No function | Check the mains connection and the fuse |
No reaction in DMX mode | Check the cable connections |
Check your DMX address setting
If available, try an alternative DMX controller
No reaction in remote mode| hange the battery in your remote control
Ensure that the IR transmitter and receiver are at close and clear distances
from each other
If the specified corrections have not led to success, please contact our service staff. The contact details can be found at www.musicstore.de
Cleaning :
Regular cleaning of the device from dirt and dust increases the shelf life of
the product. Always disconnect the device from the power supply before
cleaning it! Never clean the appliance wet! Optical lenses should be cleaned
with a dry microfiber cloth to optimize light output. Ventilation grilles and
openings should always be cleaned of dust and dirt. Suitable compressed air
sprays are recommended for this application.
Environmental protection:
The company MUSIC STORE professional GmbH always strives to reduce the burden
of packaging to a minimum. The use of environmentally friendly and recyclable
materials is of fundamental importance to us. Please dispose of and recycle
the packaging components after use properly.
Disposal of packaging:
Ensure that paper packaging, plastic materials, etc. are separately recycled.
Observe thecorresponding disposal instructions on the packaging.
Disposal of batteries:
Batteries do not belong in the garbage! Please keep batteries in accordance
with the official collection points or disposal stations in accordance with
the specifications.
Disposal of your old device:
Do not dispose of the device with household waste! This device is subject to
the WEEE Directive (Waste Electrical and Electronic Equipment) in its
currently valid version.
The device will be disposed of by an approved waste disposal company or your
local waste disposal office. The regulations valid in your country must be
observed!
Manufacturer: MUSIC STORE professional GmbH, Istanbulstraße 22-26, 51103
Cologne, Germany
Notes
MS ID: LIG0016698-000
11/2019
References
- MUSIC STORE - Online Shop für Musikinstrumente - Deutschland | MUSIC STORE professional
- Music Store Online-Shop für Musikinstrumente | MUSIC STORE professional
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>