lightmaXX LIG0014819-000 VEGA 3WAY PRO Beam WASH|FX User Manual

June 13, 2024
lightmaxx

lightmaXX - logo LIG0014819-000 VEGA 3WAY PRO Beam WASHFX
User Manual

LIG0014819-000 VEGA 3WAY PRO Beam WASH|FX

ightmaXX LIG0014819-000 VEGA 3WAY PRO Beam WASHFX 1Safety Instructions! Please read before connection and operation!
Safety Instructions! Please read before connection and operation!
WARNING: To prevent the risk of electrocution, do not open the device.
Please leave all maintenance and repairs to a qualified service workshop or contact your distributor.
The lightning fl ash symbol warns the user about non-insulated current and the risk of electrocution.
The exclamation mark symbol warns the user about important maintenance and operating inst-ructions in the manual.
Intended for indoor use only.
Read the manual.
This symbol indicates the minimum distance to illuminated objects.

  • Please recycle the packaging correctly to protect the environment.
  • Occasionally a new product may cause undesirable odors or even emit smoke for a short period of time. This reaction is normal and will disappear after a few minutes.
  • The device is intended exclusively for us indoors (IP20)! Please use this device only in dry environments. Keep the device away from rain, moisture, direct heat and dust.
  • To prevent condensation from forming in the device, please allow the device to adapt to the surrounding temperature before operating.
  •  Please position the device in a well ventilated area, beyond the reach of flammable materials or liquids.
  • Do not block any ventilation openings, as it may cause over-heating.
  • Please remove the power cable if the device is not operated for extended periods of time or maintenance is to be conducted.
  • This device is designed to operate in environments with a maximum temperature of 40° Celsius.
  • The installation of the device is not to be conducted by inexperienced persons and must adhere to the mechanical and electrical safety standards of the local law.
  • In case of a damaged power cable, it must be replaced by an original replacement part from the manufacturer.
  • Ensure that the supply voltage does not exceed the voltage
  • capacity indicated on the housing of the device.
  • In case of failure of the device, please contact the distributor and stop all operations of the device immediately.
  •  The device must keep a minimum distance of one meter from flammable materials or liquids.

WARNING: Do not look directly into the light source! Do not operate this device in the presence of persons suffering from epilepsy!

OVERHEAD INSTALLATION

The installation must be performed exclusively by qualified personnel. Incorrect installation can cause serious injuries or da-mage. Note the load limits of the selected installation position.
Ensure that during installation or dismantling/ maintenance there are no unauthorized persons below the device.
Manufacturer: MUSIC STORE professional GmbH, Istanbulstraße 22-26, 51103 Köln, Germany
Congratulations on your new Lightmaxx Moving Head!
Thank you for choosing a Lightmaxx product. Thanks to efficient development and economical production, Lightmaxx makes high-quality
products at a fantastic price possible.
Please read the operating instructions carefully to be informed about all functions of this LED system and keep it for future reference. Have fun with your new product! Your Lightmaxx Team Scope of Delivery:

Contents Quantity
1x Moving Head
1x Power Cable
2x Mounting Bracket
1x Manual

Safety instructions:

DANGER! (For Babies and Children)
Wrapping, plastic foils and other packaging material must be properly stored or disposed of. It should be kept out of the reach of babies and children due to the risk of suffocation.
Ensure that children never use the device unattended! Also make sure that children do not remove any (small) parts from the device, as they could suffocate if swallowed!
DANGER! (electric shock due to high voltages in the device)
Do not remove the housing. There are no serviceable parts in the unit. Inside the device there are components which are under high electrical voltage.
The device must not be used if damage or the absence of components, protective devices or housing parts is noticed!
DANGER! (electric shock caused by short circuit)
Modifi cations to the mains cable or the mains plug are prohibited. Failure to do so may result in fi re or death hazard due to an electric shock!
Warning! ( High light intensity – eye injuries)
It is absolutely forbidden to look directly into the light source.
Warning! (Epilepsy)
Stroboscopic effects (fl ashes of light) can cause seizures of epilepsy in some people. Accordingly sensitive people are to be warned and should avoid a look at the corresponding effects.
Warning! (Fire Hazard)
Make sure that the device is not exposed to any direct heat source and is used away from open fi re. Never block or cover ventilation slots or the device itself.
Note! (Operating conditions)
Due to its structural characteristics, the device is designed for indoor use. Do not expose the device to rain, moisture or liquids, as this can cause damage. Vibrations, dirt or sunlight can also lead to damage, avoid them!
Warning! (Power Supply)
Make sure that the device voltage matches your local mains voltage. It is strongly recommended to protect your mains socket with a residual current circuit breaker (RCD).
If you do not use your device for a longer period of time, disconnect the device from the mains to minimize dangers. The same applies to thunderstorms or fl oods, etc.

Installation:

Always check the device for damage before use. Use the original packaging or suitable transport or storage packaging to protect the product optimally from infl uences such as dust or moisture, etc. when not in use.
The device can be installed either standing or hanging. The mounting must always be done on a solid, approved support or an appropriate surface. Use the opening of the brackets to attach the device. Always create a second, separate safeguard for the device, e.g. by means of a safety wire. All work on the device (e.g. installation) should always be carried out from a stable and approved platform. Make sure that the area below you is closed off. Please note that the use of this device with a dimmer is not possible!

menu (Color Display 2.4‘TFT–X8)

DMX Adresse| 001~512| |
**Operating Mode| DMX 17 Ch| |
DMX 10 Ch| |
**
Auto| Perform Mode 1|
Perform Mode 2|
Perform Mode 3|
Perform Mode 4|
Perform Mode 5|
Perform Mode 6|
Perform Mode 7|
Perform Mode 8|
Sound| |
**** Master Audio| Perform Mode 1|
Perform Mode 2|
Perform Mode 3|
Perform Mode 4|
Perform Mode 5|
Perform Mode 6|
Perform Mode 7|
Perform Mode 8|
Master Sound| |
Slave| |
**Advanced Setting| Pan Reverse| |
Tilt Reverse| |
Display Reverse| |
Reset Motor| |
Factory Reset| |
Home Position| Password| Code = 018
| PAN| PAN = 000
| TILT| TILT = 000
| Focus| Focus = 000
| Effect Motor| EFFECT = 000
| Focus| DIMMER = 000
| | Red|
---|---|---|---
| Green|
| Blue|
| White|
| **
Language Setting|
| English
Mic Sensitive| 0|
**
System Info| Current Time| Perform Mode 5|
Total Time| Perform Mode 6|
Current Mode| Perform Mode 7|
Temperature| Perform Mode 8|
Software Version| |
****
Manual Control´**| Pan| PAN = 000|
Tilt| TILT = 000|
XY Speed| Move Speed = 000|
Focus| Focus = 000|
Effect Motor| Effect Motor = 000|
Dimmer| Dimmer = 000|
Strobe| Strobe = 000|
Red| Red = 000|
Green| Green = 000|
Blue| Blue = 000|
White| White = 000|

10 DMX Channel:

7 10CH 7 DMX Wert               Funktion
1 000-255
000-255 X-Fine
**** 2 000-255
000-255 Y-Fine
000-255 XY SPEED
3 000-255
4 000-004
005-250 Strobe effect slow to fast
251-255 Shutter open
5 000-255
6 000-255
7 000-255
8 000-255
9 000-255
**** 10 000-099
100-133 Shake from Small to Big
134-194 Backward rotation from fast to slow
195-255 Forward rotation from slow to fast

17 DMX Channel:

17CH DMX Wert Function
1 000-255
2 000-255
3 000-255
4 000-255
5 000-255
6 000-255
7 000-004
005-250 Strobe effect slow to fast
251-255 Shutter open
8 000-255
9 000-255
10 000-255
11 000-255
12 000-255
**** 13 000-099
100-133 Shake from Small to Big
134-255 Backward rotation from fast to slow
195-255 Forward rotation from slow to fast
**** 14 000-007
008-015 Red
016-023 Amber
024-031 Yellow warm
032-039 Yellow
040-047 Green
048-055 Turquoise
056-063 Cyan
064-071 Blue
072-079 Lavender
080-087 Mauve
088-095 Magenta
096-103 Pink
104-111 White 3200K
112-119 White 5600K
120-127 White 7200K
128-191 Jump from slow to fast
192-255 Fade from slow to fast
**** 15 000-009
--- ---
010-039 Focus auto run 1
040-069 Focus auto run 2
070-099 Focus auto run 3
100-129 Focus auto run 4
130-159 Focus auto run 5
160-189 Focus auto run 6
190-219 Focus auto run 7
220-255 Focus auto run 8
**** 16 000-007
008-032 X/Y auto run 1
033-058 X/Y auto run 2
059-084 X/Y auto run 3
085-110 X/Y auto run 4
111-136 X/Y auto run 5
137-162 X/Y auto run 6
163-188 X/Y auto run 7
189-214 X/Y auto run 8
215-240 X/Y auto run 9
241-255 X/Y Sound Control
17 250-255

Specifications:

Power Supply AC100-240V 50/60 Hz
Power Consumption 255 Watt(max)
Power Connection IEC
DMX 3pin-XLR male/female
Extremely Long Life LED 50,000 Hours
LED 6x 40W high power RGBW LED
DMX Modes 10/17 Channels
Zoom 4-36°
Pan/Tilt X:540°, Y:190°
Operating Modes DMX512/Master-Slave/Auto run/Music
Display LCD
Protection Class IP 20
Weight 8,5Kg

Guarantee:
The current warranty terms and conditions of Music Store professional GmbH apply.
Can be viewed under: www.musicstore.de
If you have any questions or comments, please contact:

Music Store professional GmbH
Istanbulstr. 22-26
51103 Köln
Managing Director: Michael Sauer
WEEE-Reg.-Nr. DE 41617453
Tel: +49 221 8884-0
Fax: +49 221 8884-2500
info@musicstore.de

References

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals