SCHLAGE ND Series Grade 1 Cylindrical Lock Instruction Manual

**SCHLAGE ND Series Grade 1 Cylindrical Lock Instruction Manual

**

Installation Instructions

Installation Preparation

Door preparation:

For door preparation use the template included in the package with the lock. For additional information, visit the website www.allegion.com/us

IMPORTANT – LOCK TIMING

• LOCK TIMING is the positioning and adjustment of internal lock components.
• Functions not listed below do not require timing.

ND60 (including XN12-001)
ND72 (including XN12-002 and XN12-003)

See ND-Series Timing Guide (P517-432) in package.
For additional assistance, contact Product Support at 1-877-671-7011

Install latch

Door Thickness Adjustment

• For 13⁄4” thick doors, NO ADJUSTMENT IS REQUIRED. Continue to step 2.
• For 1³⁄8” thick doors, install the optional spacers (see steps 2 and 4). No further adjustment is required. Continue to step 2.
• For 1⁵⁄8”, 2”, or 2⅛” thick doors ONLY, complete the following door thickness adjustment steps

A. Remove outside lever assembly from chassis.

B. Remove adjustment plate by rotating counter-clockwise.

Remove door thickness insert using pin wrench.

C. Reorient and replace the door thickness insert.

content/uploads/2023/10/Screenshot_6-1015.png)
2”|
2⅛”|

NOTE: If door thickness insert is missing, align the adjustment plate to marks on chassis:

rotate additional half turn counterclockwise.
1⁵⁄8”| Tighten adjustment plate to bottom, then rotate a half turn counterclockwise.
1³⁄4”| Align adjustment plate with 1³⁄4” mark. For ND85 rotate additional half turn counterclockwise.
2”| Align adjustment plate with 2” mark
2⅛”| Align adjustment plate with 2” mark, then rotate an additional full turn counterclockwise.

D. Reinstall adjustment plate.

Tighten until door thickness insert enters notch in adjustment plate (or align as described above).

If applicable, adjust turn button position.

E. Reattach the outside lever assembly to the chassis.

Tighten until snug with #2 Phillips screwdriver.

Install chassis/outside lever assembly

Latch prongs fit between slide and slide clip

Keyed IC Outside Levers ONLY:

Install outside lever and spring cage. Follow instructions in ND-Series Timing Guide.

IMPORTANT

DO NOT install IC cylinder! Follow steps in ND-Series Timing Guide!

Non-Keyed Outside Levers ONLY:

Install outside lever and spring cage, then continue to step 4

Install anti-rotation plate

Align the tab with the indent on the hub.

Install inside spring cage assembly

Install inside rose

Install inside lever

Firmly push on until lever catch engages.

Install strike

Check lock function

If a keyed function does not work properly, refer to the ND-Series Timing Guide (P517-432) in this package to determine proper  adjustment of locks that require timing. Lock functions that require timing are listed on page 1.

Additional Notes:

Revision History| Revision Description > Artwork revision. Add text on page 1 and page 5 to include new functionsND78, ND81, ND98.
---|---
A| B| C| D| E| F
066546| 069086| 074595| 075459| 089268|
MaterialWhite Paper| Edited By| Approved By| EC Number| Release Date
P. Bockelman| M. Sasso| 089268| 03-16-21
Notes1. printed two sides2. printed black3. tolerance ± .134. printed in country may vary5. drawings not to scale| TitleND-Series Instruction sheet
Creation Date 12-06-17| NumberP517-381| RevisionE
Created ByP. Brockelman| Activity3899 Hancock ExpwySecurity, CO 80911| © Allegion 2021

References

• Allegion US | Redefining Access Control & Commercial Security

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>