SCHLAGE Encode Smart WiFi Lever User Guide

October 30, 2023
Schlage

SCHLAGE Encode - logo

Smart WiFi Lever

User Guide ****

Parts

SCHLAGE Encode Smart WiFi Lever - Parts

Before you begin

  1. Setting up your lock with your smartphone?
    Start with the Schlage Home app for guided installation, set up, and pairing.

  2. Not ready to start with the app?
    You can access step-by-step interactive instructions and user guide information at:
    alle.co/EncodeLever

  3. No Internet? No problem.
    Follow this Quick Start Guide to install your lock.

Touchscreen

Communication Icon

  • Flashes when lock is connecting to WiFi to check for updates.

Low Battery Icon

  • Flashes after code is entered when battery is low.
  • Solid when battery is critical. The lock will not work without new batteries.

Programming and Input LED

  • Amber when using manual programming mode.

Home Button and Checkmark Icon

  • Turns on keypad backlight.
  • Checkmark flashes when code entry is correct.

Lock Button and “X” Icon

  • Locks the lock.
  • “X” flashes for a wrong user code.

SCHLAGE Encode Smart WiFi Lever - lock

Tools

Phillips screwdriver
Don’t use a power drill!

Step 1
Remove existing lever or knob.
Remove the entire lever, including the latch. You may also want to remove the strike. Check with your specific lever or knob manufacturer if you need help.

SCHLAGE Encode Smart WiFi Lever - Remove existing
lever

Step 2
Install the latch.
You may need to change your faceplate to fit the hole in the edge of your door.
The bevel on the latch should face the door jamb.

SCHLAGE Encode Smart WiFi Lever - Install the latch 1

Rounded corner
No change needed.
OR Square corner No mortise cut out

  1. Remove the faceplate by inserting a screwdriver into the notch and turning. Need Help?
    Visit alle.co/EncodeLever.

  2. Press square corner faceplate firmly on latch, then install.SCHLAGE Encode Smart WiFi Lever - faceplate firmly

  3. Turn to remove piece as shown, then press circular faceplate on latch.SCHLAGE Encode Smart WiFi Lever - faceplate

  4. Hammer latch into door edge using a piece of wood to protect the latch.SCHLAGE Encode Smart WiFi Lever - Hammer latch

Step 3
Install the strike into the door frame.

SCHLAGE Encode Smart WiFi Lever - strike

Step 4
Install the touchscreen.
Route the cable through the door ABOVE the latch. Push the touchscreen onto the door.

SCHLAGE Encode Smart WiFi Lever - Install the
touchscreen

Step 5
Install the backplate.

Phillips screwdriver
Don’t use a power drill!
You may damage your lock!
Route the cable over the latch and through the hole on the backplate. Secure the backplate with screws. Make sure the outside touchscreen is straight before tightening screws all the way.

SCHLAGE Encode Smart WiFi Lever - Install the
backplate

Step 6
Connect the cable.
Tuck the cable and connector in the space as shown.

SCHLAGE Encode Smart WiFi Lever - Connect the cable

Phillips screwdriver
Don’t use a power drill!
You may damage your lock!
Step 7
Secure the inside assembly to the door.
Remove battery cover to see the holes for the screws.

SCHLAGE Encode Smart WiFi Lever - inside assembly

Step 8
Install batteries and slide the cover on.

SCHLAGE Encode Smart WiFi Lever - Install batteries

If you’re having trouble installing the cylinder, or if your levers block the door, go to alle.co/EncodeLever
Step 9
Install levers.
Levers should not block the door from closing. Levers are interchangeable. Install levers to what you feel looks best on your door.

SCHLAGE Encode Smart WiFi Lever - Install levers

Follow the steps below to install the outside lever and key cylinder.

  1. Insert cylinder into lever.
  2. Insert key into cylinder. Cylinder will be held in the lever by the key.
  3. Rotate the key according to the diagram below.
  4. Press the lever with rotated key onto the lever post until it clicks into place.

After installation rotate key 90o counter clockwise to remove, and put it in a safe place.
Step 10
Test your lock

  1. Open your door!
  2. Press the lock button (on the inside of the door).
  3. Find User Code A on the label on the back of this Quick Start Guide.
  4. Enter User Code A (four digits) into the touchscreen keypad. + beep
  5. Rotate then release the lever.

Did the latch retract and then extend?

SCHLAGE Encode Smart WiFi Lever - Lock is installed Yes. Lock is installed correctly.
No. Latch retracted but did not extend (latch is stuck). See step 2 and ensure latch is moving freely.
No. Nothing happened. First check step 8 to ensure the batteries are installed firmly and correctly. If the problem persists, check step 6.

Need Help?
If your lock isn’t working, see alle.co/EncodeLever

Now that your lock is installed
you can access manual programming instructions and factory default reset (FDR) steps in the online interactive instructions.

https://alle.co/encodelever

How to use your lock

SCHLAGE Encode Smart WiFi Lever - your lock

LOCK

  • Tap the lock button on the outside touchscreen.

UNLOCK

  • Enter a valid user code. If you have an auto-relock time set in the Schlage Home app, it will auto- lock. You can disable this setting in the app.

Want to lock/unlock from anywhere or add optional voice control?
Explore compatible smart home systems at alle.co/EncodeLever

SCHLAGE Encode Smart WiFi Lever - Qr Code 1https://alle.co/encodelever

SCHLAGE Encode Smart WiFi Lever - LOCKS Pressing this button LOCKS the door.
SCHLAGE Encode Smart WiFi Lever - UNLOCKS Pressing this button UNLOCKS the door.
Your door will stay unlocked (even if auto-relock is enabled) until:

  • SCHLAGE Encode Smart WiFi Lever - LOCKS You press the inside lock button.
  • You press the lock button on the outside touchscreen.
  • You lock the door using a smart home system app.

PLACE LABEL HERE

These are your backup codes.
You will need these codes if you ever factory default reset your lock. Keep these safe!
Questions about your new
SCHLAGE Encode - logo Smart WiFi Lever?
Please don’t return it to the store!
Let us help you first!
alle.co/EncodeLever

SCHLAGE Encode Smart WiFi Lever - FINAL SIZE

Additional Notes: —————–

Revision History| Revision Description:
C > Release Revision
---|---
A| B| C| D| E| F
089048| 092568| 094350|  |  |
Material White Paper| Edited By| Approved By| EC Number| Release Date
R. Byun| D. Toppins| 094350| 4-18-2022
Notes
1. 20 page saddle-stitched booklet
2. printed two sides
3. printed full bleed
4. printed color
5. tolerance ± .13
6. printed in country may vary
7. drawings not to scale| Title
Schlage Encode Lever Quick Start Guide
Creation Date 01/25/2021| Number 47376548| Revision C
Created By R. Byun| Activity
3899 Hancock Expwy
Security, CO 80911| © Allegion 2022
SW: InDesign CC 2022

© Allegion 2022
Printed in U.S.A.
47376548 Rev. 04/22-cSCHLAGE Encode Smart WiFi Lever - Bar
Code

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals