SCHLAGE ND40 Series ND Indicator Installation Guide

June 1, 2024
Schlage

SCHLAGE ND40 Series ND Indicator

SCHLAGE ND40 Series ND Indicator

Part Identification

SCHLAGE ND40 Series ND Indicator 1

Installation Preparation

Door preparation
For door preparation use the template included in the package with the lock. For additional information, visit the website www.allegion.com/us.

Tools for Install

SCHLAGE ND40 Series ND Indicator 2

IMPORTANT – DOOR THICKNESS

This lock function is only compatible with 1-3/4” door thickness.
For thinner door applications, refer to these spacer kits:

SCHLAGE ND40 Series ND Indicator 3

Install latch
The bevel must face toward the door stop. Tighten the two (2) screws.
Note : For installation on unreinforced hollow metal doors, use of door spacer part number 24483760) is recommended.

SCHLAGE ND40 Series ND Indicator 4

Install Indicator & Chassis
Install on outside of door with slide opening aligned toward latch. If slide opening does not align with latch, refer to Chassis Handing section.

SCHLAGE ND40 Series ND Indicator 5

Install anti-rotation plate
Install on inside of door. Note that the inside push button can be adjusted depending on door thickness. The current displayed setting is for a 1-3/4” door. Align the tab with the indent on the hub.

SCHLAGE ND40 Series ND Indicator 6

Install outside spring cage assembly
Lever catch faces door edge.
Note : The outside spring cage has mounting posts.

SCHLAGE ND40 Series ND Indicator 7

Install inside spring cage assembly
Lever catch faces door edge. Install and tighten two (2) mounting screws.
Note : The inside spring cage has holes for the screws.

WARNING Do not overtighten the mounting screws.

SCHLAGE ND40 Series ND Indicator 8

Install inside rose & lever
Align dimple and groove. Rotate rose until it stops. Firmly push on lever until lever catch engages.
Note : The inside lever has a smaller hole than the outside lever.

SCHLAGE ND40 Series ND Indicator 9

Note : A pin wrench may be required to depress the lever catch if mechanism is extra tight.

Install indicator sign
Place hole in indicator sign over hook on lever and confirm the sign is on housing ledges.
Indicator sign will sit ontop of the ledges.

Note : If there is trouble with sign staying on hook, push down on counter weight and hook will move upwards to assist with installation.

SCHLAGE ND40 Series ND Indicator 10

Install escutcheon (1 of 2)
Hook escutcheon tabs into baseplate notches.

SCHLAGE ND40 Series ND Indicator 11

Install escutcheon (2 of 2)
Pivot escutcheon against door. Tighten one (1) set screw into baseplate slot with hex key.

SCHLAGE ND40 Series ND Indicator 12

Install emergency button and plunger.

SCHLAGE ND40 Series ND Indicator 13

Install outside lever
Push lever on until it clicks into place.
Note : The outside lever has a larger hole than the inside lever.

SCHLAGE ND40 Series ND Indicator 14

Note : A pin wrench may be required to depress the lever catch if mechanism is extra tight.

Install strike

SCHLAGE ND40 Series ND Indicator 15

Complete

SCHLAGE ND40 Series ND Indicator 16

Continue to next page to check lock function.

Checking lock function

  1. Push the inside button to lock the outside lever.
    Check that the outside lever is locked and that the Indicator sign raises to read “Occupied.”

  2. Rotate the inside lever to release the button and unlock the outside lever.
    Check that the outside lever is unlocked and the Indicator sign lowers to read “Vacant.”

  3. Push the inside push button to relock the outside lever.
    Check that the outside lever is locked and that the Indicator sign raises to read “Occupied.”

  4. Rotate the emergency turn (44 function) or use a flat screwdriver to rotate the emergency button (40 function) to release the inside button.
    Check that the outside lever is unlocked and the indicator sign lowers to read “Vacant”.

  5. The inside lever should always be unlocked and rotate freely.

Chassis Handing

  1. Complete this step only if the slide opening does not align with the latch.
    A Use Phillips screwdriver to loosen and remove screw.
    B Separate the indicator assembly from the lock chassis.

SCHLAGE ND40 Series ND Indicator 17

C Rotate Chassis 180° to align slide opening towards latch.
D Rotate both cams downwards. Chassis must be unlocked in order to rotate upper cam.

SCHLAGE ND40 Series ND Indicator 18

E Reassemble chassis and indicator assembly. Tighten one (1) screw.
F Confirm that the upper cam is engaged with the slider and lower cam is engaged in rectangular hole.

SCHLAGE ND40 Series ND Indicator 19

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals