SCHLAGE S1 Smart Deadbolt User Guide

SCHLAGE S1 Smart Deadbolt

Product Information

The S1 Smart Deadbolt is a keyless smart deadbolt that provides enhanced security and convenience for your home. It features a keypad for easy entry, status indicators for lock status, and various customization settings. The deadbolt comes with all the necessary parts for installation, including exterior and interior assemblies, mounting screws, strike plate, reinforcement plate, and 4 AA Alkaline batteries.

Exterior Assembly

• Keypad for entering PIN codes
• Status Indicators: Green – Unlocked or setting success, Red – Locked or setting failed
• Cylinder (S1 only)
• Reboot button

Interior Assembly

• Battery cover
• Reset button
• Thumb turn for manual locking and unlocking
• Wireless module socket

Settings

• Master PIN code
• Auto lock
• Beeper
• Wrong code entry limit
• Shutdown time
• Away mode
• Bluetooth mode

Product Usage Instructions

Preparing for Installation

1. Measure the dimension of the hole on your door to ensure you have a 54mm hole, or use the drilling template provided.
2. Adjust the deadbolt backset if needed by turning the bolt case and pulling it to extend to the desired position (either 60mm or 70mm).
3. Change the default master PIN code [12345678] to a new code before programming the lock.

Installation

1. Install the bolt on the door with the word “UP” in the upward position.
2. Test if the deadbolt works smoothly with a screwdriver.
3. Ensure the bolt is in the retracted (unlocked) position before installing the lockset.
4. Hold the exterior assembly flush to the door and pull the key tailpiece and cable through the door hole. If using the optional cross bolt, securely tighten it before mounting it on the door.
5. Position the inside mounting plate on the door, ensuring the cable and tailpiece go through the holes in the mounting plate.
6. Secure both assemblies using the provided screws, making sure the exterior assembly is vertically aligned. If using the cross bolt, securely tighten it to the exterior Ease unit with the additional screw provided.
7. Attach the cable assembly to the interior assembly PCB by aligning notches on top of the cable connector to slots on the PCB connector. Press the connector firmly until completely connected.
8. Install the interior assembly on the inside mounting plate, keeping the tailpiece in a horizontal position.
9. Secure the interior assembly to the mounting plate using 4 screws.
10. Test the operation of the deadbolt using the backup key and thumb turn before installing batteries.

Note : Resetting the lock before use is required for proper operation.

Parts
(S1 Smart Deadbolt shown)

For more information visit schlage.com.au/ease or schlage.co.nz/ease

Exterior assembly

Status Indicators

• Green:
  Unlocked or setting success

• Red:
  Locked or setting failed

Interior assembly
Master and User PIN codes have 100 digits. The default master PIN code is [12345678]. Please change it before programming the lock.

Preparing for installation

1. Measure the dimension of the hole on your door to ensure you have a 54mm hole, or use the drilling template provided.
2. Adjust the deadbolt.
   • NOTE: Bolt ships with backset in 60mm (2-3/8”) position. If required, turn the bolt case and pull to extend to 70mm (2-3/4”) backset position (pictured below). The bolt must be in a retracted (unlocked) position when you are changing the backset

Installation

1. Install the bolt on the door ensuring the word UP is in the upwards position.
2. Use a screwdriver to test if the deadbolt works smoothly.
3. Make sure the bolt is in the retracted (unlocked) position.
   • NOTE: The bolt must be in a retracted (unlocked) position before installing the lockset.
4. Hold the exterior assembly flush to the door, and pull the key tailpiece and cable through the door hole.
   • NOTE : Cable must go through door hole under the bolt.
   • NOTE : The tailpiece should be kept in a horizontal position.
5. Position the inside mounting plate to sit flush with the door, ensuring the cable and tailpiece go through the holes in the mounting plate.
6. Secure both assemblies using the screws provided. Make sure the exterior assembly is vertically aligned. If you added the cross bolt, securely tighten the post to the exterior Ease unit with the additional screw provided.
7. Attach cable assembly to the interior assembly PCB by lining up notches on top of the cable connector to slots on the CB connector. Press the connector in firmly until completely connected.
8. Install interior assembly on the inside mounting plate.
   • NOTE : The horizontal orientation of the tailpiece as you insert the inside escutcheon (thumb turn should be vertical).
9. Secure using 4 screws through the interior assembly onto the mounting plate.
   • NOTE: Test operation using the backup key and thumb turn before installing batteries, see if the bolt extends smoothly.
10. Reset the lock to learn the orientation of your door.
    • NOTE: Resetting the lock before use is required and crucial for the lock to operate properly.
    • Keep your lock in  “unlock” status, and insert 4x AA batteries in the battery pack
    • Using a pointed object, press and hold the reset button for over 5 seconds.
    • If reset is successful, the latch bolt will extend on its own to learn the orientation of the door.
11. Install battery cover.
12. Install reinforcement plate and strike into the door jamb.

Warnings

• Do not install batteries until the lock is completely installed on the door.
• Failure to follow these instructions could result in damage to the product and void the factory warranty.
• The accuracy of the door preparation is critical for the functioning and security of this product. Misalignment can cause performance degradation and lessening of security.
• Finish Care : This lockset is designed to provide the highest standard of product quality and performance. Care should be taken to ensure a long-lasting finish. When cleaning is required, use a soft, damp cloth. Do not use lacquer thinner, caustic soaps, abrasive cleaners, or polishes as these can damage the coating and result in tarnishing.

Definitions

• Auto lock:
  After successful code entry and the unit unlocks, it will automatically re- lock after 30 seconds. This feature is disabled in the default setting.

• Away mode:
  This feature can be activated or deactivated in the Schlage Abode App or the lock itself. Activating away mode will disable all user codes, except master away mode. If the lock is opened with a key or manually from inside, the lock will trigger an alarm. To deactivate the away mode, you have to enter the master code or deactivate it in the app.

• Fake PIN code:
  Random numbers that are added before or after the user’s PIN. This prevents the user’s PIN from being exposed.

• Manual mode:
  The auto lock function can be adjusted to manual mode. In manual mode the lock can be locked by pressing any key on the keypad for 2 seconds or using the thumb turn from the internal unit.

• Master mode:
  The master mode should be entered by entering [** Master PIN Code #] to program the lock.

• Master PIN code:
  The master PIN code is used for programming and feature settings.

• Reset button:
  After the reset operation, the lock will be restored to factory default settings, all user credentials will be deleted. Refer to page 6 for instructions on how to reset your lock.

• Shutdown time:
  The lock will shut down for a default of 3 minutes and not allow operation after the wrong code entry limit (5 times) has been met. When the unit is shut down, the light will flash if you are trying to use the keypad.

• Silent mode:
  Disables the tone sound.

• Status indicators:
  Located on exterior assembly.

• User PIN code:
  The user PIN code operates the lock. Maximum number of user PIN codes is 20.

Hardware specifications

Lock operation

Notes;

1. After each successful setting entry, 2 green lights and 2 beep indicators will occur.
2. The beeping sound occurs only when sound is enabled.
3. If the indicators show 3 red lights and 3 beeps, your setting has failed and the system will exit master mode. Please enter master mode to try again.
4. Refer to page 10 for guidelines on setting PIN codes.

Setting PIN codes

1. Master PIN code (4 10 digits):
   The default master PIN code is “12345678”, please modify it after installation. If you forget your master PIN code, you can reset your lock back to factory settings (refer to page 6 for instructions).

2. User PIN code (4 10 digits): User PIN codes can be set up through the master PIN code. Up to 20 user PIN codes can be stored.

3. Both master and user PIN codes don’t support the following combination of numbers.

How to use

Unlock the door

1. 1. Unlock the door from outside:
   Master/User PIN code or key

2. Unlock the door from inside:
   Manual thumb turn

   • Turn the thumb on the inside body

Lock the door

1. Lock the door from outside:
   • Auto-lock mode: In auto-lock mode, after unlocking, the bolt will extend out automatically after 30 seconds.
   • Manual mode: Press any key on the keypad for 2 seconds.
2. Lock the door from inside:
   • Auto lock mode: In auto-lock mode, the device will lock automatically.
   • Manual mode: Turn the thumb on inside the body.

Unlock with a fake PIN code

Users can prevent PIN code exposure from strangers by entering random digits before or after the PIN code.

Warranty conditions
The Schlage Ease™ provides a 2-year mechanical and electronic warranty. Our goods come with guarantees that cannot be excluded under local consumer law. You are entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. The warranty does not cover any defect or damage that may be caused or partly caused if the goods are not properly maintained, installed, or are not suitable for the specified application.

Refer to our website for our finish warranty.

Get mobile access with Schlage Abode
For an enhanced experience and functionality, try using the Schlage Ease™ with the Schlage Abode mobile application. Simply download the Schlage Abode app from the Apple App Store or the Google Play Store. Manage and control your lock with the ease of your smartphone for greater control and access.

Schlage Wi-Fi Bridge (AB100)
Empower your Schlage Ease™ lock with Wi-Fi capability. The Schlage Wi-Fi Bridge (AB100) pairs with your Schlage Ease™ lock, to provide you with a real- time connection through your smartphone.

Ask your retailer about the Schlage Wi-Fi Bridge (AB100), sold separately.

For more information visit allegion.com.au/ease or allegation.co.nz/ease

Australia

• 1800 098 094
• info.au@allegion.com
• www.allegion.com.au

New Zealand

• 0800 477 869
• nzinfo@allegion.com
• www.allegion.co.nz

New Zealand

• 0800 477 869
• nzinfo@allegion.com
• www.allegion.co.nz

PDSC0032R1

References

• Ease Smart Locks
• Schlage EASE
• Allegion NZ Homepage
• Allegion | Seamless Access and a Safer World

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>