Commercial Electric 567101111 Power and Light The Lamp User Guide
- June 13, 2024
- Commercial Electric
Table of Contents
Item # 1009578324/
1009595413/ 1009578323
Model # 567101111/
567102111/ 567102121
Use and Care GUIde
46In. x 10In. Color electability flus Mount
Package contents
| Part | description | Quantity |
|---|---|---|
| A | Fixture Body | 1 |
| B | Mounting Bracket | 1 |
Hardware Included
| Part | description | Quantity |
|---|---|---|
| AA | Wire Connector | 3 |
| BB | Drywall Anchor | 4 |
| CC | Mounting Screw | 4 |
| DD | Electrical Box Screw | 2 |
note: Keep your receipt and these instructions for proof of purchase.
Warning: RISK OF ELECTRIC SHOCK. Ensure the electricity to the wires you
are working on is shut off. Either remove the fuse or turn off the circuit
breaker before removing an existing light fixture or installing the new one.
If you are unfamiliar with electrical installations, we recommend you contact
a qualified electrician to do the installation.
Installation
note: Select a suitable location that can support the weight of the
fixture. Determine the method for mounting the fixture before drilling, based
on the type of ceiling.
note: Two people are recommended for the installation of this light
fixture.
-
Open the package and remove the lamps, then remove the mounting bracket (B). Mount the mounting bracket (B) to the electrical box using the two electrical box screws (DD). Mark four holes locations for mounting, then remove the mounting bracket (B).
-
Drill four 1/8-in. pilot hole into the screw locations marked on the ceiling. You can also use an awl or nail to dimple the screw holes. Install a drywall anchor (BB) and a mounting screw (CC) in each drilled mounting hole to tighten the mounting bracket (B).
note: Do not need drill hole on wooden surface. -
Hang the two hanging cables on the lamp at the D place of the mounting bracket (B). Connect the hot and neutral (black and white) wires from the J-box to the same color wires from the fixture body (A). Connect the green wire from the J-box to the grounding wire from fixture body (A) and mounting bracket (B). Cover the wire connections using the wire connectors (AA).
Make sure to fasten them well.
-
Turn on the power and light the lamp, and move the toggle switch to the desired color temperature gear (as shown below, 3000 K left 4000 K right 5000 K).
note: The factory setting for the correlated color temperature (CCT) is 3000K, which is the warmest white light. -
Insert the two E’s on one side of the fixture body (A) with the edge of the mounting bracket (B) respectively, and then level the top of the whole fixture body (A) to the ceiling, then slide the fixture to the right, and then check whether the fixture is installed firmly.
-
Put the lamps and lanterns, turn on the power supply can all function normally.
Selecting Main light Or nightlight Mode (Only For Modell 567101111)
The product can be used in one of two modes: Main light mode, which provides
full brightness and allows selection from three color temperatures, or
nightlight mode.
Nighlight mode provides reduced light output at 2000K color temperature for
very soft illumination at night.
TO TURN ON THE MAIN LIGHT
- Turn on the light switch to activate the light fixture.
TO CHANGE TO NIGHTLIGHT MODE WITH REDUCED LIGHT OUTPUT
- Switch the main light off and back on again in 3 seconds to active nightlight mode.
note: The main light will not provide light output when the nightlight trim is illuminated.
TO RETURN TO THE MAIN LIGHT WITH FULL LIGHT OUTPUT WHEN IN NIGHTLIGHT MODE Toggle the switch off and back on to active.
Care and cleaning
Caution: Before attempting to clean the tube and luminaire/light fixture, disconnect the power to the fixture by turning the breaker off or removing the fuse from the fuse box. Clean with a soft, dry cloth. Do not use cleaners with chemicals, solvents, or harsh abrasives. Do not use liquid cleaner on the LEDs, LED driver, or wiring.
Troubleshooting
Minor problems often can be fixed without the help of an electrician.
Warning: Before doing any work on the fixture, disconnect power to the
light fixture.
| Problem | Possible Cause | Solution |
|---|---|---|
| The fixture will not light. | The power is off. | Ensure the power supply is on. |
| The circuit breaker is off. | Ensure the circuit breaker is in the on position. | |
| There is a bad connection. | Check to ensure proper wire connections are made. |
Contact a qualified electrician.
There is a defective switch.| Contact a qualified electrician.
The fuse blows or the circuit breaker trips when the light is turned on.| The
wires are crossed or the power wire is grounding out.| Check the wire
connections.
Contact a qualified electrician or call customer service
1-877-527-0313.
The light fixture flickers or makes a buzzing sound.| The dimmer circuit is
not compatible with the product.| Check the product page at www.HomeDepot.com
for a list of compatible dimmers.
The dimming circuit is set outside the dimming range of the product.| Turn or
slide the dimmer switch to adjust the light output until the flickering or
buzzing stops.
Out of sync| Slide the dimmer too fast.| Turn off the wall switch for more
than 3 seconds, then turn back on.
The dimmer circuit is not compatible with the product.| Check the product page
at www.HomeDepot.com for a list of compatible dimmers.
Warning: Carefully read and understand the information given in this
manual before beginning the assembly and installation.
Failure to do so could lead to electric shock, fire, or other injuries which
could be hazardous or even fatal.
- Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker.
- To reduce the possibility of serious injury, always take the proper precautions and unplug the fixture before moving or cleaning.
- Risk of fire or electric shock.
notice: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna, increase the separation between the equipment and the receiver, connect the equipment into an outlet on a circuit different from that to which the receiver is connected, and consult the dealer or an experienced radio/TV. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Warranty
what is covered
The manufacturer warrants this lighting fixture to be free from defects in
materials and workmanship for a period of five (5) years from date of
purchase. This warranty applies only to the original consumer purchaser and
only to products used in normal use and service. If this product is found to
be defective, the manufacturer’s only obligation, and your exclusive remedy,
is the repair or replacement of the product at the manufacturer’s discretion,
provided that the product has not been damaged through misuse, abuse,
accident, modifications, alterations, neglect, or mishandling.
what is not covered
This warranty shall not apply to any product that is found to have been
improperly installed, set-up, or used in anyway not in accordance with the
instructions supplied with the product. This warranty shall not apply to a
failure of the product as a result of an accident, misuse, abuse, negligence,
alteration, faulty installation, or any other failure not relating to faulty
material or workmanship. This warranty shall not apply to the finish on any
portion of the product, such as surface and/or weathering, as this is
considered normal wear and tear.
The manufacturer does not warrant and specifically disclaims any warranty,
whether express or implied, of fitness for a particular purpose, other than
the warranty contained herein. The manufacturer specifically disclaims any
liability and shall not be liable for any consequential or incidental loss or
damage, including but not limited to any labor / expense costs involved in the
replacement or repair of said product.
Contact the Customer Service Team at
1-877-527-0313 or visit
www.HomeDepot.com.
Questions, problems, missing parts? Before returning to the stor
call Commercial Electric Customer Service
8 a.m. – 7 p.m., EST, Monday – Friday
9 a.m. – 6 p.m., EST, Saturday
1-877-527-0313 | HOMedePOT.cOM
Retain this manual for future use.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>