HOFFEN HB-2155 Hand Blender Set Instruction Manual
- June 13, 2024
- Hoffen
Table of Contents
HOFFEN HB-2155 Hand Blender Set Instruction Manual
INTENDED USE
The appliance is intended for whipping, mixing and shredding food ingredients.
Follow the instructions in this manual for safe installation and use of the
appliance.
This appliance is intended for private indoor use only; it may not be used for
commercial purposes.
TECHNICAL SPECIFICATIONS
- Lot No.: POJM220155
- Model: HB-2155
- Power supply: 220-240 V~, 50/60 Hz
- Power consumption: 800 W
SAFETY INSTRUCTIONS
- This appliance must not be used by children without supervision. Keep the appliance and its cord away from children.
- The appliance may be used by persons with reduced physical, sensory or mental capabilities, or by individuals lacking the relevant experience and knowledge, provided that they are supervised or use the appliance safely, in compliance with the user’s manual, and understand the hazards involved.
- Children must not play with the appliance.
- Turn off the device and disconnect it from the power source before changing accessories orapproaching moving parts.
- Always unplug the appliance from the outlet if it is left unattended or before assembly, disassembly or cleaning.
- The device’s maximum operation time is 90 seconds. After operating it for 3 minutes, disconnect the device from the power source and wait 2 minutes before operating it again.
- When cleaning parts that come into contact with food, follow the section 8 Cleaning and maintenance.
- Care shall be taken when handling the sharp cutting blade and during cleaning.
- Switch off the appliance and disconnect from supply before changing accessories or approaching parts that move in use.
- Warning! Risk of injury in the event of misuse. Use extreme caution when removing accessories, especially when installing and removing blades and the blade.
- Only use the accessories included with the device.
- If the power cord is damaged, it must be replaced by the manufacturer, an authorized service centre or a qualified individual in order to avoid hazard.
- Read this manual thoroughly before first use.
- Before connecting the appliance to a power source, make sure that the electric grid specifications correspond to the parameters indicated on the data plate.
- The appliance should be connected to a 220-240 V~ 50/60 Hz mains.
- When using electrical appliances, especially in the presence ofchildren, basic safety precautions should be observed in order to avoid the risk of fire or electric shock.
- This product is intended for household use only. Only use the appliance for its intended purposes.
- The appliance is not intended for use by means of an external clock or a separate remote control system.
- To protect against electrical shock, do not immerse the power cord, plug, or appliance itself in water or any other liquid.
- Do not let the cord hang over the edge of the worktop or sink.
- Do not use the appliance near flammable fabrics (curtains, carpets), and do not place it near sources of heat: gas heaters, electric cookers.
- Unwind the power cord before use.
- The power cord should not hang freely or touch any hot surface.
- Do not cover the appliance during operation. A fire could occur if the blender is covered or touching flammable material.
- When using the appliance, never insert your hands or other objects (forks, knives etc.) into the ingredients being mixed.
- Do not touch moving appliance components (rotating elements). Keep your fingers, hair and clothes away from all moving parts.
- The blender must be supervised at all times when connected to a power source.
- Do not operate the appliance when it is damaged or after it malfunctions.
- Do not use the appliance if it has been dropped or any damage is visible.
- Do not attempt to open the housing or remove any parts of the appliance.
- Use only the included accessories.
- Never direct the blades towards your or anyone else’s face when you are operating the appliance.
- Retain this manual and packaging, if possible.
- If you intend to hand this appliance over to a third party, hand over this user’s manual as well.
- You can download a file containing this manual at: http://instrukcje.vershold.com.
MEANING OF SYMBOLS
Read this user’s manual.
The product is compliant with the requirements of the applicable EU directives.
Recycling of waste electrical and electronic equipment – see the RECYCLING section of this user’s manual.
Unplug the appliance.
Product suitable for contact with
food.
The appliance is intended for indoor use.
Protection class II – in
appliances of this protection class, protection against electric shock is
ensured by adequate (double or reinforced) insulation, which is unlikely to
fail.
Trademark indicating that the manufacturer has made a financial contribution to the development and operation of a packaging materials recovery and recycling system.
Recycling code identifying the material from which the packaging is made – corrugated cardboard.
Segregation sign – Labeling
indicating the need for waste segregation.
Paper waste – Designation of the
container to which the waste should go.
Designation of the relevant
waste bin – plastic.
Symbols in monochrome printout only for illustartion.
APPLIANCE COMPONENTS
- On switch and speed control knob
- Blender body
- Grinding attachment
- Whisk attachment
- Whisk
- Container 0.6 l
- Mini food processor lid
- Mini food processor container 0.6 l
- Blade
KIT CONTENTS
| Qty | Element |
|---|---|
| 1 | Blender with power cord |
| 1 | Grinding attachment |
| 1 | Container 0.6 l |
| 1 | Whisk with attachment |
| 1 | Mini food processor container with lid 0.6 l |
| 1 | Blade |
| 1 | User’s manual |
Open the packaging and carefully take out the appliance. Ensure that the package is complete and none of its contents are damaged. Check that plastic parts are not broken and the power cord is not damaged. If you find that any components are missing or damaged, contact the vendor and do not use the appliance. Retain the packaging or recycle it in accordance with local regulations.
Attention! To keep children safe, do not leave packaging parts (plastic bags, cardboard boxes, expanded polystyrene elements etc.) freely accessible. Danger of suffocation!
USE
Before first use
- Unpack the appliance and remove all packaging elements.
- Check to ensure the power supply parameters correspond to the parameters of the local electrical grid.
- Before first use, clean the appliance and accessories in accordance with the instructions contained in section 8 Clening and care.
Speed control
The speed of rotation can be adjusted using the on switch and the speed
control knob.
To increase the speed of rotation, the on switch and the speed control knob
must be pressed harder and harder. Thestronger the pressure, the faster the
speed.
To reduce the speed of rotation – release the pressure on the on switch and
the speed controler knob.
Operating the blender with the grinding attachment
You may use the grinding attachment to prepare dips, sauces, soups, mayonnaise, baby meals and milk cocktails.
- Make sure that the appliance is unplugged.
- Mount the grinding attachment onto the blender body by inserting it into the attachment and turning it clockwise to lock it.
- Prepare food ingredients in the 0.6 l container.
- Connect the appliance to 220-240V~ 50/60 Hz mains.
- Insert the grinding attachment into the container.
- Press and hold the on switch. To increase the speed, press harder on the switch.
- To disassemble, grasp the blender with both hands, one by the blender body and the other by the grinding attachment. Then turn both parts in opposite directions.
The attachment should be facing down when removing / installing.
Never use the appliance continuously for more than 90 seconds. After this period, unplug the appliance from the outlet and wait about 2 minutes before switching it on again.
The temperature of the food being prepared should not exceed 35°C. Unplug the
appliance before replacing accessories or approaching moving parts during
operation.
If the blades get jammed during operation, immediately release the low speed
or high speed button. Unplug the appliance and remove the cause of the jam. If
you operate the appliance with the blades jammed, you may damage the blender.
The blades are sharp – exercise caution.
Operating the blender with the 0.6 l mini food processor
In this configuration, use the blender to grind such products as: meat, cheese, onions, herbs, garlic, walnuts, almonds, prunes etc. Do not chop any hard products such as nutmeg, coffee beans or grain.
- Fit blades on the spindle inside the 0.6 l container. The 0.6 l container should be placed on a flat, dry and stable surface.
- Insert the food ingredients into the 0.6 l container (do not exceed 2/3 of the container).
- Fit the container lid on the 0.6 l container.
Attention! The 0.6 l container edges and the container lid edges are profiled. Do not use force to connect these elements. If you feel any resistance, turn the 0.6 l container slightly. Do not use the appliance without the lid properly attached.
- Attach the container lid to the blender body by inserting it into the hole in the lid and turning it clockwise to lock it.
- Connect the appliance to the 220-240V ~ 50/60 Hz mains. Press and hold the on switch. During operation, use one hand to hold the 0.6 l container and the other hand to hold the blender. After use, unplug the appliance.
- Remove the blender body from the container lid by holding the cover with one hand and unscrewing the blender body with the other.
- Remove the container lid from the 1.5 l container.
- Take out the disc or blades carefully.
Attention!
Never use the appliance continuously for more than 90 seconds. After this
period, unplug the appliance from the outlet and wait about 2 minutes before
switching it on again.
The temperature of the meal being prepared should not exceed 35°C.
Unplug the appliance before replacing accessories or approaching moving parts
during operation.
If the blades get jammed during operation, immediately release the low speed or high speed button. Unplug the appliance and remove the cause of the jam. If you operate the appliance with the cutting blades jammed, you may damage the blender.
**** The blades are sharp – exercise caution.
Operating the blender with the whisk
In this configuration, you may prepare such dishes as: whipped cream, meringue, instant desserts.
-
Make sure that the appliance is unplugged.
-
Mount the beater attachment on the blender by inserting the blender body into the attachment and turning it clockwise to lock it.
-
Connect the whisk attachment to the whisk.
-
Prepare food ingredients in the 0.6 l container.
-
Connect the appliance to 220-240V~ 50/60 Hz mains.
-
Insert the whisk into the 0.6 l container.
-
Press and hold the on switch. To increase the speed, press the switch harder.
To reduce RPM, reduce the pressure on the switch. -
After use, unplug the appliance.
-
Remove the whisk from the whisk attachment.
-
To disassemble, hold the blender with both hands, one by the blender body and the other by the attachment of the beater. Then turn both parts in opposite directions. The attachment should be facing down when removing / installing.
Attention!
Never use the appliance continuously for more than 90 seconds. After this
period, unplug the appliance from the outlet and wait about 2 minutes before
switching it on again.
The temperature of the meal being prepared should not exceed 35°C.
Unplug the appliance before replacing accessories or approaching moving parts
during operation.
CLEANING AND CARE
Basic rules
Proper and regular cleaning will ensure safe operation and extend the useful life of the appliance
Warning! Switch off the
appliance, unplug it and let it cool down before cleaning and maintenance to
avoid electric shock and burns.
- It is recommended that the blender be wiped with a soft, damp cloth or paper towel and left to dry.
- All other components should be washed in lukewarm water with some mild detergent.
- Use a wooden or plastic spatula to remove stubborn food residues.
- You may use a cotton swab to remove food residues from hard-to-reach places.
Attention!
Do not clean the appliance with any strong chemicals, alkali, abrasive or
disinfecting agents, as they may damage the surface of the appliance.
Do not use sharp, coarse or metal cleaning tools, since they could damage
appliance surfaces!
Do not immerse the blender or power cord in water or any liquid. Exercise caution when cleaning the appliance the blades are sharp
REPAIR
The appliance contains no parts that could be serviced by the user. Do not
attempt to repair the appliance on your own. Always have the appliance
repaired by a professional.
If the blender cord is damaged, it must be replaced by the manufacturer,
service centre or a qualified person in order to avoid hazard.
STORAGE AND TRANSPORTATION
- The appliance must be cleaned as described above and left until it is completely dry.
- Always store the appliance in a dry and well-ventilated room, beyond children’s reach.
- During transportation, protect the appliance against vibration and shocks
RECYCLING
Keep the packaging materials out of children’s reach, as the materials can
pose a hazard.
The packaging should be disposed of in accordance with local regulations.
- According to the WEEE Directive 2012/19/EU, the crossed-out wheelie bin symbol is used to label all electric and electronic devices requiring segregation.
- Do not dispose of the spent product with domestic waste: hand it over to an electric and electronic device collection and recycling centre.
- Hazardous components in electronic and electrical equipment have a negative impact on the environment and human health.
- Plastics contained in the device can be recycled in accordance with the specific marking. By recycling materials and spent equipment you will help to protect the environment.
- Information on electric and electronic devices collection centres is available from local government agencies or from the vendor.
CE DECLARATION
The appliance has been designed, manufactured and marketed in compliance with the New Approach Directives. Therefore, the product bears the “CE” mark and has a declaration of conformity, which is available to market supervision agencies for inspection.
WARRANTY AND SERVICE
To submit a complaint in relation to the appliance, deliver it to a Customer Service Point at any Biedronka store.
Should you have any questions and issues related to product operation or submitting a complaint, send them to the following e-mail address: infolinia@vershold.com or contact us by phone at: +48 667 090 903
Your opinion is important to us. Evaluate our product at: www.vershold.com/opinie
Warranty and post-warranty technical support service is provided by :
QUADRA-NET Sp. z o.o.
ul. Dziadoszańska 10
61-248 Poznań, Polska
phone no. 61/853 44 44
mobile no. 664 44 88 00
e-mail: infolinia@quadra-net.com
URL: www.quadra-net.pl
Manufacturer (Warrantor)
VERSHOLD POLAND Sp. z o.o.
Ul. Żwirki i Wigury 16A
02-092 Warsaw, Poland
Made in China
Warranty card
- Stamp
- Date of sale
- Signature
- Device name
- Device mode
- Serial No. or lot No
Warranty Terms and Conditions
-
The Warrantor of this product grants a 36-month warranty valid from the purchase date, subject to presenting a properly filled-out warranty card. Under this Warranty, the product shall be, at the Warrantor’s discretion:
a) repaired free-of-charge by the Warrantor, provided that any disassembled, damaged or faulty parts of the product, in the interest of the Client’s safety, shall become the property of the Warrantor,
b) exchanged for a new product at the place of purchase; as a result, the damaged or faulty product shall become the property of the Warrantor,
c) subject to return with a refund of the purchase price; as a result, the damaged or faulty product shall become the property of the Warrantor. -
A faulty/damaged product means a product failing to provide the features described in the user manual due to intrinsic properties of the appliance.
-
The Beneficiary under the warranty shall deliver the appliance to the Customer Service Point at a given store in order to submit a complaint about the appliance. When exercising your warranty rights, present proof of purchase (receipt, invoice) and describe the defect in as much detail as possible, including in particular external manifestations.
-
A warranty card without a stamp, purchase date and a signature of the vendor is invalid.
-
The warranty excludes products with physical damage other than that caused by the manufacturer or distributor, including specifically any damage resulting from incorrect usage or force majeure.
-
The warranty does not cover products whose protective seal has been removed, unless such a removal was done by an authorised service technician.
-
The authorised repair facility shall make every effort to complete the repair within 21 days. This deadline may be extended to 1 month, should the repair require a purchase of replacement parts which are not accessible onsite.
-
It is recommended that the entire product be turned over upon submission of a complaint, so as to facilitate service operations.
-
This warranty for the sold consumer product does not exclude, restrict or suspend any rights of the Buyer stemming from warranty regulations covering defects in goods sold pursuant to the Civil Code of 23 April 1964 (Journal of Laws Dz.U.2014.121).
-
The warranty shall be applicable within the territory of the Republic of Poland.
References
- HOFFEN - Strona główna - HOFFEN
- Wyszukiwanie instrukcji
- Quadra Net - sieć serwisowa, serwis AGD, RTV, IT
- vershold.com/opinie
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>