Amerock Era Cabinet Knob Installation Guide

: May 15, 2024
: Amerock

Table of Contents

Installing New Cabinet Hardware
A. Mounting Pulls
B. Mounting knobs
REPLACING CABINET HARDWARE
CUSTOMER SERVICE
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Amerock Era Cabinet Knob

Installing New Cabinet Hardware

Step 1. Location of Cabinet Hardware

While there are no hard, fast rules for placement of a knob or pull on a cabinet door, most cabinet makers will locate them approximately 3″-4″ above the upper non-hinged corner on base cabinets, or the lower non-hinged corner on wall cabinets. However, the decision is your to make!

Wall Cabinets
Base Cabinets
Wall or Base Cabinets
Drawers

Step 2. Mounting Cabinet Hardware

When drilling for a knob or pull, a 3/16″ hole is recommended for most styles. The exception is pulls that have “studs”.
A stud is simply an extension of the molded screw holes. If a pull has a stud, then a 1/4″ hole is required with studs sitting securely in the wood.
Mounting Cabinet Hardware

IMPORTANT Screw Information

Amerock® includes 8-32 x 1″ long machine screws with most knobs and pulls because the typical cabinet door or drawer front is 3/4″ thick. This screw length should work in most applications. However, if your cabinet doors or drawer fronts are thicker than 3/4″, then you will need to use longer screws for mounting. Check the thickness of both a cabinet door and a drawer front in your kitchen, as the thickness dimensions may not be the same. In general, the screw length(s) used should be 1/4″ longer than the thickness of your cabinet door or drawer front material. It is not uncommon for some drawers to be constructed with a 3/4″ thick front attached to a 3/4″ thick drawer box. In this situation, the total drawer thickness is 1-1/2″, making a 1-3/4″ long screw necessary for mounting. These screws may be purchased from any hardware store. Please note that select hardware sold by Amerock may include metric screws instead of UNC screws.

A. Mounting Pulls

Mounting Pulls

Sizes Available
Pulls can be obtained in U.S. measurements as well as metric.
Amerock offers a broad range of sizes to choose from.

How to Choose the Right Size

Take note of all sizes available.
3″ is the most common size pull.
Size is determined by measuring from hole to hole, not by the length of the pull itself

Installation Tips
If you are using a pull, you will want to determine the hole center spacing of the pull. 3″ hole centers are the most common, however, Amerock offers a wide variety of sizes. You may want to create or purchase a durable template prior to drilling to mark the mounting holes. This will help to ensure that they are parallel with the door or drawer edge and that they are the same placement height on every cabinet.
WARNING! An example is provided below, however, do not use this for drilling purposes as printers may provide template distortions.

Common Hole Center Measurements

Installation Tips

B. Mounting knobs

Sizes Available
Knobs can be obtained in a variety of sizes, shapes, and diameters. Amerock offers a broad range of sizes to choose from.

How to Choose the Right Size
There are no right or wrong sizes when it comes to selecting the appropriate knob size. Choose the size that looks best in proportion to the size of your cabinet doors and drawers. A 1-1/4″ or 1-3/8″ diameter knob is the most popular.

To create a dramatic effect, consider using a large (1-1/2″ diameter or greater) or small (1″ diameter or smaller) sized knob.
Small sized knobs also work well on applications such as apothecary drawers, spice drawers, pullout cutting boards, etc.

Installation Tips
If you are installing a knob, it is suggested that you create or buy a durable template prior to drilling to mark the mounting hole.
This will help to ensure that the knob is positioned properly on the cabinet door or drawer front and that there is the same placement height on every cabinet.

REPLACING CABINET HARDWARE

A. Pulls

When replacing pulls, the choices are numerous. You may choose to go with a pull with the same hole centers as your existing pull. Pull size is determined by measuring from hole to hole, not by the length of the pull itself. However, if you do choose to use a pull which is longer or shorter, the following information will assist you:

On wall cabinets, reuse the bottom hole and drill a new top hole
On base cabinets, reuse the top hole and drill a new bottom hole
On drawers, drill two new holes and realign in the center

B. Knobs

When replacing knobs, simply unscrew your old knob. Leaving the old screw in place, screw on your new knob.
Nothing could be easier!

C. Backplates

If you are switching sizes of pulls, or from a knob to a pull, or from a pull to a knob, there may be one or more exposed holes in the cabinet surface. To remedy this situation, you may choose to use a backplate.

Backplates are used in conjunction with a knob or a pull. It is placed between the cabinet door or drawer surface and the knob or pull. Backplates will also help to protect the wood surface, and visually enhance the existing decorative hardware.

Note: If you are switching from a knob to a pull or from a pull to a knob, generally there will be one or more exposed holes in the cabinet surface!
Backplate will cover the old mounting holes.