LNC A04988H5 Hybris 5 Light Island Instruction Manual
- June 13, 2024
- LNC
Table of Contents
Hybris 5 Light Island
Item Number: A04988H5
Instruction Manual
A04988H5 Hybris 5 Light Island
WARNING (To reduce the risk of fire, electric shock, or personal injury):
-
We suggest installation by a licensed electrician.
-
Please read the instruction carefully and save it as you may need it at a later time.
-
Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
» Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
» Place the wall switch in the “OFF” position. -
Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
-
Make sure that the ceiling or wall can stand the weight of the lamp before installation.
-
Make sure the voltage you are using is 120V. The maximum wattage is Type B, Max 40W per bulb.
-
Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
-
When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
-
The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT
TOOLS REQUIRED (NOT INCLUDED):
Before starting assembly and installation please prepare the needed tools
as below picture
PARTS TYPE & QTY INCLUDING
(C) Single bar (1)
(D) Green ground screw (1)
(E) Canopy (1)
(F) Loop (4)
(G) Quick link (4)
(H) Hex nut (1)
(I) Cap nut (1)
(J) Chain (2)
(K) Tube (2)
(L) Arm assembly (2)
(M) Pipe (5)
(N) Arm (1)
(O) Iron frame (5)
(P) Nut (15)
(Q) Glass shade (5)
ACCESSORIES & QTY ENCLOSED:
(A) Wire connector (3)
(B) Mounting screw (2)
(P) Nut (1) (spare part)
ASSEMBLY & INSTALLATION INSTRUCTIONS:
-
Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
-
Make pre-installation Step A1 » By measuring, determine the correct number of links needed for proper hanging height. Using the chain pliers, disconnect and discard the unwanted part.
Step A2 » Screw tubes (K) onto arm assemblies (L) and pipes (M) onto arms (N) as shown in the illustration.
Step A3 » Open quick links (G). Attach quick links (G) to loops (F) on canopy (E) and on the top of tubes (K). Close quick links (G).
Step A4 » Carefully weave the fixture wires through chains (J) in and out of every other link and then pass wires through the loop (F) on canopy (E). Gently pull the wires to ensure the wires are not stressed. -
Turn off power
Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
» Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
» Place the wall switch in the “OFF” position. -
Make installation
Step B1 » Unscrew hex nut (H) and cap nut (I) from single bar (C).
Step B2 » Attach single bar (C) to the outlet box with mounting screws (B).
Note: the side of single bar (C) marked “GND” must face out.
Step B3 » If needed, shorten the length of fixture wires. At this point, the remaining wire length measured above single bar (C) is at least 6″.
Step B4 » Make wire connections
Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Connect ground wires according to the below chart Connect wires according to the below chart
*** Connect Black or Red Supply Wire to:| Connect White Supply Wire to:
---|---
Black| White
Parallel cord (round & smooth)| *Parallel cord (square & ridged)
Clear, Brown, Gold or Black without tracer| Clear, Brown, Gold or Black with tracer
Insulated wire(other than green) with copper conductor| Insulated wire(other than green) with silver conductor
-
Note: When parallel wires (SPT I& SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.) • Twist wires together with plastic wire connectors until tightly joined.
• Wrap each connector with approved electrical tape and sure that no wire strands are exposed.
• Carefully tuck all wires into the outlet box.
Step B5 » Raise canopy (E) to the ceiling and secure canopy (E) in place by tightening hex nut (H) and cap nut (I) onto the pre-assembled threaded nipple on single bar (C).- Check everything is already installed properly, then you could turn on the light. Enjoy!
NOTE: The canopy (E) should be snug against the ceiling and cap nut (I).
If not, adjust the threaded length of the pre-assembled threaded nipple on single bar (C):
• Unscrew the pre-assembled hex nut.
• Screw the pre-assembled threaded nipple in or out of single bar (C).
• When the secure length is achieved, tighten the pre-assembled hex nut and back to step B5.
Step B6 » 1) Unscrew nuts (P) from iron frames (O).
- Check everything is already installed properly, then you could turn on the light. Enjoy!
- Align holes of glass shades (Q) with holes of iron frames (O).
- Screw nuts (P) into holes to secure glass shades (Q) and iron frames (O) as shown in the illustration.
- Install bulbs (not included) (Please do not exceed the maximum wattage recommended on the socket.)
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
+1 850 296 2377
Working hours : Mon Fri 9:00 – 16:00 EST
homecustomercare@outlook.com
Documents / Resources
| LNC
A04988H5 Hybris 5 Light
Island
[pdf] Instruction Manual
A04988H5 Hybris 5 Light Island, A04988H5, Hybris 5 Light Island, 5 Light
Island, Light Island, Island
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>