LNC A04988W2 Hybris 2 Light Vanity Light Instruction Manual
- June 13, 2024
- LNC
Table of Contents
LNC A04988W2 Hybris 2 Light Vanity Light
Product Information:
- Item Number: A04988W2
- Contact Number: +1 850 296 2377 (Working hours: Mon – Fri 9:00 – 16:00 EST)
- Email: homecustomercare@outlook.com
WARNING (To reduce the risk of fire, electric shock, or personal injury):
- We suggest installation by a licensed electrician.
- Please read the instruction carefully and save it as you may need it at a later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
- Mounting surface should be clean, dry, flat, strong enough and 1/4 larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16 should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before installation.
- Make sure the voltage you are using is 120V. The maximum wattage is Type B, Max 40W per bulb.
- Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
- When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
Product Usage Instructions:
- Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
- Turn off power before starting the installation. NEVER attempt any work without shutting off the electricity until the work is done.
- Secure mounting plate (D) to the outlet box with mounting screws (A).
- Connect wires according to the provided chart for wire connections. Note that the ground wire is a bare copper wire and should never be connected to other wires.
- Follow the instructions for connecting black or red supply wire and white supply wire to the outlet box ground, fixture ground, and dimples.
- Use the provided cupped washer for proper wire connection.
- If using parallel wires (SPT I & SPT II), ensure that the neutral wire is square shaped or ridged, while the other wire is round in shape or smooth.
Please refer to the provided image for tools required for assembly and installation:
Parts Included:
- (C) Green ground screw (1)
- (D) Mounting plate (1)
- (E) Back plate (1)
- (F) Knob nut (2)
- (G) Pipe (2)
- (H) Arm (2)
- (I) Nut (6)
- (J) Iron frame (2)
- (K) Glass shade (2)
Accessories Enclosed:
- (A) Mounting screw (2)
- (B) Plastic wire connector (3)
- (I) Nut (1) (spare part)
Item Number: A04988W2
WARNING (To reduce the risk of fire, electric shock, or personal injury):
-
We suggest installation by a licensed electrician.
-
Please read the instruction carefully and save it as you may need it at a later time.
-
Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
» Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position.
» Place the wall switch in the “OFF” position. -
Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
-
Make sure that the ceiling or wall can stand the weight of the lamp before installation.
-
Make sure the voltage you are using is 120V. The maximum wattage is Type B, Max 40W per bulb.
-
Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
-
When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
-
The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT
TOOLS REQUIRED (NOT INCLUDED)
Before starting assembly and installation please prepare the needed tools as below picture
PARTS INCLUDING
- (C) Green ground screw (1)
- (D) Mounting plate (1)
- (E) Back plate (1)
- (F) Knob nut (2)
- (G) Pipe (2)
- (H) Arm (2)
- (I) Nut (6)
- (J) Iron frame (2)
- (K) Glass shade (2)
ACCESSORIES ENCLOSED
- (A) Mounting screw (2)
- (B) Plastic wire connector (3)
- (I) Nut (1) (spare part)
ASSEMBLY & INSTALLATION INSTRUCTIONS
-
Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
-
Turn off power
Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
» Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position.
» Place the wall switch in the “OFF” position. -
Make assembly
* Step A1 » Unscrew knob nuts (F) from back plate (E), then set them aside for later installation.
* Step A2 » Carefully pass the supply wires from the outlet box through mounting plate (D). Secure mounting plate (D) to the outlet box with mounting screws (A).
* Step A3 » Make wire connections Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES
Twist wires together with plastic wire connectors until tightly joined, and
wrap each connector with approved electrical tape. Be sure that no wire
strands are exposed and then carefully tuck all wires into the outlet box.
* Step A4 » Align the holes in back plate (E) with the pre-assembled mounting screws, then attach back plate (E) to mounting plate (D) with the previously removed knob nuts (F). Hand tighten until snug.NOTE: back plate (E) should be snug against the wall with knob nuts (F).
If not, remove back plate (E), adjust the threaded length of pre-assembled
mounting screws on mounting plate (D):
Unscrew the pre-assembled hex nuts.
Screw the pre-assembled mounting screws in or out of mounting plate (D).
When the secure length is achieved, tighten the pre-assembled hex nuts and
back to Step A4.
* Step A5 » 1) Screw pipes (G) to top of arms (H) as shown in the illustration.
* Unscrew nuts (I) from iron frames (J).
* Align holes of glass shades (K) with holes of iron frames (J).
* Screw nuts (I) into holes to secure glass shades (K) and iron frames (J) as shown in the illustration.
* Install bulbs (not included) (Please do not exceed the maximum wattage recommended on the socket.)- Check everything is installed properly, then you could turn on the light. Enjoy!
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>