LNC A05152A Morrisave 22.8 Inch 3-Light Matte Gold Bell LED Modern-Contemporary Vanity Light Instruction Manual

LNC A05152A Morrisave 22.8 Inch 3-Light Matte Gold Bell LED Modern-

Contemporary Vanity Light

Product Information

• Item Number : A05152A
• Maximum Wattage: Type A, Max 60W per bulb
• Voltage : 120V

Parts Included

• (C) Green ground screw (1)
• (D) Mounting plate (1)
• (E) Back plate (1)
• (F) Knob nut (2)
• (G) Socket (3)
• (H) Lampshade (3)
• (I) Gasket (3)
• (J) Socket ring (3)

Accessories Enclosed

• (A) Mounting screw (2)
• (B) Plastic wire connector (3)

Product Usage Instructions

• *  **Step 1** : Preparation

  • Make sure the mounting surface is clean, dry, flat, and strong enough to support the lamp.

  • The mounting surface should be 1/4 larger than the canopy on all sides.

  • If there are any gaps between the mounting surface and canopy exceeding 3/16, correct them as required.

  • Ensure that the ceiling or wall can withstand the weight of the lamp.

  • Check that the voltage you are using is 120V.

  • Ensure the maximum wattage per bulb does not exceed 60W (Type A).

  • Keep the lamp away from acidic and alkaline substances to avoid damaging the surface.

  • Step 2 : Installation

  • Turn off the power before starting the installation.

  • Secure the mounting plate (D) to the outlet box using the
    provided mounting screws (A).

  • Connect the wires according to the below chart

with copper conductor
Clear, Brown, Gold or Black with tracer| Insulated wire(other than green) with silver conductor

1. * Twist the wires together with plastic wire connectors (B) until tightly joined.

   • Wrap each connector with approved electrical tape.
   • Ensure no wire strands are exposed and carefully tuck all wires
     into the outlet box.

2. Step 3 : Bulb Replacement

   • Turn off or unplug the lamp before replacing bulbs.
   • Wait until the lamp is cool as bulbs can get hot quickly.

Item Number:A05152A
WARNING (To reduce the risk of fire, electric shock, or personal injury)

1. We suggest installation by a licensed electrician.
2. Please read the instruction carefully and save it as you may need it at a later time.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
   • Go to the main fuse, or circuit breaker, box in your home.
   • Place the main power switch in the “OFF” position.
   • Place the wall switch in the “OFF” position.
4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
6. Make sure the voltage you are using is 120V. The maximum wattage is Type A, Max 60W per bulb.
7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

TOOLS REQUIRED (NOT INCLUDED)
Before starting assembly and installation please prepare the needed tools as below picture

PARTS INCLUDING

• (C) Green ground screw (1)
• (D) Mounting plate (1)
• (E) Back plate (1)
• (F) Knob nut (2)
• (G) Socket (3)
• (H) Lampshade (3)
• (I) Gasket (3)
• (J) Socket ring (3)

ACCESSORIES ENCLOSED

• (A) Mounting screw (2)
• (B) Plastic wire connector (3)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

2. Turn off power
   Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.

   • Go to the main fuse, or circuit breaker, box in your home.
   • Place the main power switch in the “OFF” position.
   • Place the wall switch in the “OFF” position.

3. Make assembly

• Step A1 » Unscrew knob nuts (F) from back plate (E), then set them aside for later installation.
• Step A2 » Carefully pass the supply wires from the outlet box through mounting plate (D). Secure mounting plate (D) to the outlet box with mounting screws (A).
• Step A3 » Make wire connections

Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.

Connect ground wires according to the below chart

Connect wires according to the below chart

Note: When parallel wires (SPT I& SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)

Twist wires together with plastic wire connectors (B) until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.

Step A4 » Align the holes in back plate (E) with the pre-assembled mounting screws, then attach back plate  (E) to mounting plate (D) with the previously removed knob nuts (F). Hand tighten until snug.

NOTE: back plate (E) should be snug against the wall with knob nuts (F).
If not, remove back plate (E), adjust the threaded length of pre-assembled mounting screws on mounting plate (D)

• Unscrew the pre-assembled hex nuts.
• Screw the pre-assembled mounting screws in or out of mounting plate (D).
• When the secure length is achieved, tighten the pre-assembled hex nuts and back to Step A4.

Step A5

1. Remove socket rings (J) from sockets (G).
2. Carefully place lampshades (H) to sockets (G), and then screw socket rings (J) to sockets (G) through gaskets (I) to secure them as shown in the illustration.
3. Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the socket.)
4. Check everything is installed properly, then you could turn on the light. Enjoy!

ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>