LNC A0356901 Borislav 22 Inch 3-Light Polished Gold Globe LED Modern-Contemporary Vanity Light Instruction Manual
- June 13, 2024
- LNC
Table of Contents
A0356901 Borislav 22 Inch 3-Light Polished Gold Globe LED Modern-
Contemporary Vanity Light
Item Number: A0356901
WARNING (To reduce the risk of fire, electric shock, or personal injury):
-
We suggest installation by a licensed electrician.
-
Please read the instruction carefully and save it as you may need it at later time.
-
Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
A) Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
B) Place the wall switch in the “OFF” position. -
Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all side. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
-
Make sure that the ceiling or wall can stand the weight of the lamp before installation.
-
Make sure the voltage you are using is 120V. The maximum wattage is Type A,Max 60W per bulb.
-
Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
-
When replacing bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
-
The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur.
It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT:
TOOLS REQUIRED (NOT INCLUDED):
Before starting assembly and installation please prepare the needed tools as below picture
PARTS INCLUDING:
(C) Green ground screw (1)
(D) Mounting plate (1)
(E) Screw (2)
(F) Glass shade (3)
(G) Back plate (1)
(H) Arm (3)
(I) Socket cup (3)
ACCESSORIES ENCLOSED:
(A) Mounting screw (2)
(B) Plastic wire connector (3)
(J) Iron bar (9)
(K) Plastic anchor (2)
(L) Wood screw (2)
ASSEMBLY & INSTALLATION INSTRUCTIONS:
-
Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
-
Turn off power
Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
A) Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
B) Place the wall switch in the “OFF” position. -
Make assembly
Step A1: Unscrew the screws (E) from the back plate (G) then gently remove the
mounting plate (D).
Step A2: Secure mounting plate (D) to outlet box with mounting screws (A),
plastic anchors (K) and wood screws (L).
Step A3: Make wire connections
Connect wires as below wires connecting shown. PLEASE NOTE THAT GROUND WIRE IS
BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Connect ground wires according to the below chart Connect wires according to
the below chart ****
Connect Black or Red Supply Wire to: | Connect White Supply Wire to: |
---|---|
Black | White |
*Parallel cord ( round & smooth ) | *Parallel cord ( square & ridged ) |
Clear,Brown,Gold or Black without tracer | Clear,Brown,Gold or Black with |
tracer
Insulated wire ( other than green ) with copper conductor| Insulated wire (
other than green ) with silver conductor
*Note: When parallel wires ( SPT I & SPT II ) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth ( see illus.)
Twist wires together with plastic wire connector until tightly joined, and
wrap each connector with approved electrical tape. Be sure that no wire
strands are exposed and then carefully tuck all wires into the outlet box.
Step A4: Align the holes in the back plate (G) with the pre-assembled mounting
screws, then attach the back plate (G) to the mounting plate (D) using the
previously removed screws (E). Tighten until snug.
Step A5: Install bulbs (Not included) (Please do not exceed the maximum
wattage recommended on the socket.)
Fix the glass shade (F) onto the socket cup (I) then tighten iron bars (J).
4. Check everything is installed properly, then you could turn on the
light. Enjoy!
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner
(such as mild and non-abrasive soap.)
Do not use abrasive materials such as scouring pads or powders, steel wool or
abrasive paper.
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.
**** +1 850 296 2377 Working hours : Mon – Fri 9:00 a.m. – 16:00 p.m. EST
homecustomercare@outlook.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>