MINKA LAVERY 5035-66A Muncie 5-Light Black Candle Chandelier Instruction Manual

: June 13, 2024
: MINKA LAVERY

Table of Contents

MINKA LAVERY 5035-66A Muncie 5-Light Black Candle Chandelier
Product Information
Product Usage Instructions
INSTALLATION INSTRUCTION
Hardware Bag
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MINKA LAVERY 5035-66A Muncie 5-Light Black Candle Chandelier

Product Information

The product is an indoor light fixture with the item number 5035-66A. It is designed to be mounted on the ceiling and provides illumination with up to five candelabra base bulbs. The fixture comes with all the necessary parts for installation, including a
crossbar, mounting screws, a ground screw, rods, a fixture loop, a canopy, a lock collar, and a quick link. The fixture is compatible with CFL or LED bulbs, with a maximum wattage rating of 60 watts per bulb.

Product Usage Instructions

Before starting the installation, make sure to shut off the power at the fuse box or circuit breaker.
Remove the old fixture, including the mounting hardware.
Carefully unpack the new fixture and ensure that all parts are included.
Adjust the arms of the fixture to the desired position.
Determine the desired hanging height and thread rods B and C through coupling D, carefully feeding wires through each rod as you assemble.
Thread fixture loop A onto rod B.
Attach cap F with screws G to hole E of the fixture.
Thread all thread into the ceiling loop until snug.
Thread the other end of the all thread into the crossbar and use a lock collar to secure it.
Connect the electrical wire as shown in Fig. 3. Ensure that all wire connectors are secured.
If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the crossbar using the provided green screw.
Tuck the wire connections neatly into the outlet box and raise the canopy all the way to the ceiling.
Raise the lock collar and thread it onto the ceiling loop protruding through the canopy.
Install up to five candelabra base bulbs or CFL/LED equivalents, not exceeding the maximum wattage rating.
Once the installation is complete, restore power to the outlet box and test the fixture.

Note: The illustration in Fig. 1 is for installation purposes only and may not be identical to the fixture purchase

INSTALLATION INSTRUCTION

ASSEMBLE THE FIXTURE FIG. 1 &FIG.3

Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.
Carefully unpack your new fixture and lay out all the parts in a clean area. Take care not to misplace any small parts necessary for installation.
Attach a crystal ball (T) to the tube (S).
Install fabric shade (M) on arms (R) using metal nuts (N) and place decorative ring (L）on fabric shade (M).
Determine the desired height and thread rods (G1 and G2) together. Screw loop (I1) to the rod (G1). Pass the wires carefully through each rod as you assemble. Attach the bottom end of the rod into the coupling (J).
Attach quick link (H) to loop (I2) on canopy (D). Carefully feed the wire through loop (I1), quick link (H), and loop (I2).
Attach the circular strap (B) to the junction box using the junction box screws (C). The side of the circular strap (B) marked “GND” must face out. The mounting screw can be adjustable if necessary.
The support cable is provided to support the weight of the fixture while wiring. Align the fixture to circular strap (B) and attach the hook on the end of support cable (E) into a slot located on circular strap (B). Carefully allow the support cable (E) to support
the weight of the fixture while wiring.
CONNECTING THE WIRES FIG. 2

MINKA LAVERY-5035-66A-Muncie-5-Light-Black-Candle-Chandelier-
fig-2

Connect the electrical wires as shown in Figure 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the circular strap (B) using the green screw provided.
Tuck the wire connectors neatly into the junction box.
COMPLETING THE INSTALLATION Fig. 1
Raise the fixture over the mounting screws (A) and secure it with decorative nuts (F).
Place candle covers (Q) over sockets (V), then place tube covers (K) over candle covers (Q). Install (4) four candelabra base bulbs (X) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification—DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).
Attached leaf finial (O) with coupling (P).

The leaves on the lamp body can be manually adjusted to change their shape Your installation is now complete. Turn on the power supply of the junction box to test the fixture.