Minka Lavery 3041-560 60W 1 Light Medium E-26 Incandescent Vanity Fixture Instruction Manual

Minka Lavery 3041-560 60W 1 Light Medium E-26 Incandescent Vanity Fixture

Product Name: Item#3041-560

Using Instructions

1. Shut off power at the fuse box or circuit breaker box.
2. Remove the old fixture including the mounting hardware.
3. Carefully unpack your new fixture and lay out all the parts in a clear area. Take care not to misplace any small parts necessary for installation.
4. Thread all thread (E) into crossbar (C). Note: The length of all thread (E) into crossbar (C) may be adjusted, if necessary.
5. Secure all thread (E) to crossbar (C) using lock washer (B) and hex nut (A).
6. Take the crossbar assembly (C) and mount it to the outlet box with mounting screws (D) (Size: #8-32N*L0.5). The side of crossbar marked with GND must face out.
7. Connect the electrical wires as shown in Fig. 2, making sure that all wire connectors are secured. If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directlyto the crossbar (C) using the green screw provided. After the wires are connected, tuck them carefully inside the outlet box.
8. Place the fixture body (F) over all thread (E) and secure with finial (G).
9. Place the glass shade (I) followed by large metal ring (J) and small metal ring (K) over socket (H). Secure with screw shell (L) using tool (M).
10. Install one medium base bulb (N) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification. DO NOT EXCEED THE MAXIMUM WATTAGE RATING!
11. Your installation is now complete. Return power to the outlet box and test the fixture.

Note: The illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

READ AND SAVE THESE INSTRUCTIONS

WARNING:  SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.

INSTALLATION INSTRUCTIONS

MOUNTING THE FIXTURE (Fig. 1)

1. Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts in a clear area. Take care not to misplace any small parts necessary for installation.
3. Thread all thread (E) into crossbar (C). Note: The length of all thread (E) into crossbar (C) may be adjusted, if necessary.
4. Secure all thread (E) to crossbar (C) using lock washer (B) and hex nut (A).
5. Take this crossbar assembly (C) and mount it to outlet box with mounting screws (D) (Size: #8-32N*L0.5”). The side of crossbar marked with “GND” must face out.

CONNECTING THE WIRES (Fig. 2)

1. Connect the electrical wires as shown in Fig. 2, making sure that all wire connectors are secured. If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the crossbar (C) using the green screw provided. After the wires are connected, tuck them carefully inside the outlet box.

COMPLETING THE INSTALLATION (Fig.1)

1. Place fixture body (F) over all thread (E) and secure with finial (G)
2. Place glass shade (I) followed by large metal ring (J) and small metal ring (K) over socket (H). Secure with screw shell (L) using tool (M).
3. Install (1) one medium base bulb (N) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification—DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!). Your installation is now complete. Return power to the outlet box and test the fixture.

Note: Illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>