PANADERO Ambar 3V Wood Heating Stove Owner’s Manual

: June 13, 2024
: PANADERO

Table of Contents

PANADERO Ambar 3V Wood Heating Stove
Product Information
Product Usage Instructions
USAGE AND MAINTENANCE INSTRUCTIONS
INSTALLATION
FUNCTION
MAINTENANCE
GUARANTEE
MEASUREMENTS AND CHARACTERISTICS
HOW TO OPERATE YOUR WOOD STOVE EFFICIENTLY
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PANADERO Ambar 3V Wood Heating Stove

Product Information

The ONIX 3V, DIAMANT 3V, and AMBAR 3V are wood-burning stoves that provide an ecological source of energy. Wood is a renewable source of energy that meets the energy and environmental demands of the 21st century. These wood-burning stoves burn logs cleanly without leaving any residue and produce wood ash, which is a high-quality fertilizer rich in mineral salts. The combustion of wood does not increase the CO2 in the atmosphere, making it an ecological source of energy that does not contribute to the greenhouse effect. By purchasing one of these wood-burning stoves, you can help the environment, have an economical heating solution, and enjoy watching the flames.

Product Usage Instructions

Before installing the wood-burning stove, it is essential to read and follow the usage and maintenance instructions provided in this manual. Proper installation in accordance with legislation is required.

Position of the Smoke Pipe

Place the right-angled tube joint in the smoke outlet at the back of the stove.
Insert the tube into the bend.
Repeat step 2 with the other tubes.
Join the smoke pipe to the rest of the chimney.

Wood: an ecological fuel

Wood is a renewable source of energy that answers the energy and environmental demands of the 21st century.
Throughout its long life, a tree grows from sunlight, water, mineral salts, and CO2. Following the general pattern of nature, it soaks up energy from the sun and supplies us with the oxygen essential for animal life.
The quantity of CO2 given off during the combustion of wood is no greater than that given off by its natural decomposition. This means we have a source of energy that respects the natural cycle of millions of years. Burning wood does not increase the CO2 in the atmosphere, making it an ecological source of energy that plays no part in the greenhouse effect.
In our wood-burning stoves logs are burnt cleanly without leaving any residue. Wood ash is a high-quality fertilizer, rich in mineral salts.
In buying a wood-burning stove, you will help the environment, your heating will be very economical and you will be able to enjoy watching the flames, something no other form of heating can offer.

USAGE AND MAINTENANCE INSTRUCTIONS

You have purchased a PANADERO product. Apart from correct maintenance, our woodstoves require installation strictly in accordance with legislation. Our products conform to the EN 13240:2001 and A2:2004 European norm, however, it is very important for you the consumer to know how to correctly use your woodstove following the recommendations we set out. For this reason, before installing our product you must read this manual carefully and follow the usage and maintenance instructions.

POSITION OF THE SMOKE PIPE

Place the right-angled tube joint in the smoke outlet at the back of the stove.
Place the tube in the bend, and do the same with the other tubes.
Join it to the rest of the chimney.

IGNITION
The stove you have just bought offers the best performance, high efficiency, and CO and dust extremely low emissions. In order to get these benefits, the preheated air enters into the combustion chamber through the stove’s top. To favor ignition, you should follow the next tips:

If possible, you should always use small dried pine pieces pilled up. Put under this bunch 1 or 2 firelighters and, above ir, the dried firewood cut in half lengthwise. Once the firelighter fired, close the door and open the air inlet to the maximum. When the fire takes a correct intensity, you can regulate the heat at your convenience with the lower air inlet.

INSTALLATION

Under no circumstances should you place horizontally the tubes as it could block the proper smoke evacuation and the stove’s correct function.
All local regulations, including those referring to National and European standards, need to be complied with when installing the appliance.
The installation of the smoke outlet must be as vertical as possible, avoiding the use of joints, angles, and deviations. If the installation is connected to a masonry chimney pipe we recommend the tubes reach the exterior exit. If the smoke outlet is via tubing only, at least three meters of vertical tubing are recommended.
IMPORTANT : The installation and regular cleaning of this stove must be carried out by a qualified professional. The ventilation opening must never be obstructed.
IMPORTANT : The woodstove must be installed in a well-ventilated place. It is advisable to have at least one window in the same room as the stove which can be opened.
The tube connections should be sealed with a refractory putty to prevent soot from falling through the joints.
Do not position the stove near combustible walls. The stove should be installed on a non-combustible floor surface, if not a metal plate covering the bottom surface area of the stove must be placed underneath it and extend further than 15 cm at the sides and 30 cm at the front.
Whilst the stove is in use remove any material nearby which could be damaged by the heat: furniture, curtains, paper, clothes, etc. The minimum safety distance from adjacent combustible materials is as shown on the last page of this manual.
The ease of access for the cleaning of the product, smoke outlet, and chimney must be considered. If you intend to install your stove near an inflammable wall, we advise you to leave a minimum distance to facilitate cleaning.
The stove should be installed on the flooring with adequate support. If your current floor does not comply with this criterion, it should be adapted with appropriate measures (for example, a weight distribution plate).

FUEL

Use only dry wood with a maximum moisture content of 20%. Wood with a moisture content higher than 50 or 60% does not heat and combusts very badly, and creates a lot of tar, releases excessive amounts of vapor and deposits excess sediments onto the stove, glass, and smoke outlet.
The fire should be lit using special fire lighters, or paper and small pieces of wood. Never try to light the fire using alcohol or similar products.
Do not burn domestic rubbish, plastic materials or greasy products that can pollute the environment and lead to risks of fire due to obstruction of the pipes.
In TRRRIVVVISIOOON stoves, in order for the side windows to remain clean, the firewood to be used must be very dry, with a humidity percentage of less than 111222%%%…

FUNCTION

It is normal for smoke to appear during the first few uses of the stove, as certain components of the heat-resistant paint burn whilst the pigment of the actual stove is fixed. Therefore the room should be aired until the smoke disappears.
The wood stove is not designed to function with the door open under any circumstances.
The stove is intended to function intermittently with intervals for recharging the fuel.
For the lighting process of the stove, it is recommended you use paper, fire lighters or small sticks of wood. Once the fire starts to burn, add to it two logs of wood each weighing 1 to 1.3 kg as a first initial charge. In this lighting process, the air inlets of the stove must be kept completely open. If necessary the drawer for removing ashes can also be opened to begin with. Once the fire is more intense, close the drawer completely (if open) and regulate the intensity of the fire by closing and opening the air inlets.
In order to achieve the stated nominal heat output of this stove a total quantity of 1.38 kg. of wood must be placed inside at intervals of 45min. The logs should be positioned horizontally and separate from one another, to assure a correct combustion. In any instance a charge of fuel must not be added to the stove until the previous charge has been burnt, leaving only a basic fire bed which is enough to light the next charge but no stronger.
After the first initial lighting, the brass pieces of the stove may become a coppery color.
It is normal for the seal of the glass door panel to melt with use. Even though the stove can function without this seal, it is recommended that you replace it seasonally.
The lower drawer can be removed in order to clear out ash. Empty it regularly without waiting for it to fill up too much, to avoid the grill becoming damaged. Take care with the ash which may still be hot up to 24 hours after the stove has been used.
Do not open the door abruptly in order to avoid smoke being released, and never open it without opening the air draught beforehand. Open the door only in order to put in the appropriate fuel.
The glass, brass pieces, and stove in general may reach very high temperatures. Do not expose yourself to the risks of burns. When handling metal pieces, use the glove provided with the stove.
Keep children away from the stove.
If you have trouble lighting the stove (due to cold weather, etc.) it can be lit with folded or scrunched-up paper which is easier to light.
In case of the stove becoming too hot, close the air draughts to reduce the intensity of the fire.
In case of malfunction, contact the manufacturers.

MAINTENANCE

It is advisable to clean the glass door panel periodically to avoid blackening by soot deposits. Professional cleaning products are available for this. Never use water. Never clean the stove while it is in use.
It is also important to clean the smoke outlet tubing periodically and check there are no blockages before relighting fuel after a long period of non-use. At the start of each season, a professional should carry out a revision of the installation.
In the event of a fire in the smoke outlet, close all air draughts if possible and contact the authorities immediately.
Any replacement part which you may need must be recommended by us.

GUARANTEE

This is a high-quality stove, manufactured with great care. Even so, if any defect is found please first contact your distributor. If they are unable to solve the problem they will contact us and send us the stove if necessary. Our company will replace any faulty parts free of charge up to five years from the date of purchase. We will not charge for repair work, however, any transport costs must be paid by the client. Since this apparatus has been tested by a homologated laboratory the following parts are NOT covered by warranty: