GE Lighting Solon 3 Light Vanity Integrated LED 5 Color Temperatures Installation Guide

GE Lighting Solon 3 Light Vanity Integrated LED 5 Color Temperatures

Installation Guide

www.gelighting.com

The GE brand and logo are trademarks of the General Electric Company.
©2022 GE Lighting, a Savant company. Information provided is subject to change without notice.
All values are design or typical values when measured under laboratory conditions.

TOOLS REQUIRED

INSTALLATION

Remove the fixture and the mounting package from the box and make sure that no parts are missing by referencing the illustrations on the installation instructions.
Before installation, select your preferred correlated color temperature (CCT) by moving the switch to 2700K, 3000K, 4000K, 5000K, or 6500K.

Caution: Turn off the main power at the circuit breaker before installing

the fixture. Failure to disconnect power supply prior to installation may result in possible shock or death.

1. Remove existing fixture and disconnect all electrical

2. Remove mounting bracket[lO] from fixture canopy[14] by removing canopy nuts[13].
   

3. Mark two hole locations on the wall that align with hole distance in mounting bracket[lO]. Drill two holes with 5/16″ size drill bit at the marked locations. Insert drywall anchors[9] into each drilled mounting

4. Place mounting bracket[lO] onto outlet box[1], fix mounting bracket[lO] tightly by using two mounting bracket screws[12]. Insert self-tapping screws[13] into drywall anchors[9] to secure the mounting bracket[lO] tightly against the
   

5. Connect black supply wire[2] to black fixture wire[7] and connect white supply wire[3] to white fixture wire[8] by using P4 wire nuts[5]. Connect ground fixture wire[6] at the top of the fixture canopy[14] to power supply ground wire[4] from outlet box[1]. Wrap P4 wire nuts[5] with electrical tape for a more secure Carefully tuck wires back into the outlet box[l]. Do not get wires pinched between ceiling and canopy.
   

6. Attach fixture canopy[14] onto mounting bracket[10] by canopy nuts[13] previously removed . Note: Fixture can be mounted in the up or down

7. Remove all LED shields[16] from fixture metal Do not touch LED during or after installation.
   

8. Screw glass shade[17] onto threaded socket of fixture metal body in a clockwise Repeat for remaining glass shades[17]. Do not over tighten.
   

PRODUCT COVERED

Model

DIMMING

5

• The luminaire is dimmable with most commonly available 14
• Ensure that your dimmer is rated for LED or CFL loads and has a low-end trim or calibration. Follow the dimmer manufacturer’s instructions to set the low-end

WARNING

Risk of fire or electric shock: LED wall light installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.

• Consult a qualified electrician to ensure correct branch This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
• These products are intended to be used in dry or damp
• Min 90°C (194°F) supply conductors suitable for operation in an ambient

This device complies with Part 15 of the FCC Rules. Operations is subject to the following two conditions: (1) This device may not cause harmful interference.
GE Lighting, a Savant company • 1-800-435-4448 • www.gelighting.com

GE IS A TRADEMARK DF GENERAL ELECTRIC COMPANY. USED UNDER TRADEMARK LICENSE. ©2021 GE LIGHTING, A SAVANT COMPANY INFORMATION PROVIDED IS SUBJECT TD CHANGE WITHOUT NOTICE. All VALUES ARE DESIGN OR TYPICAL VALUES WHEN MEASURED

www.gelighting.com

The GE brand and logo are trademarks of the General Electric Company.
©2022 GE Lighting, a Savant company. Information provided is subject to change without notice.
All values are design or typical values when measured under laboratory conditions.
And 2) this device must accept any interference received, including interference that may cause undesired operation. This device complies with CAN ICES-005 B.Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area may cause _
_harmful interference in which case the user will be required to correct the

interference at his own expense.

PREPARE ELECTRICAL WIRING

� Electrical Requirements
� The LED fixture must be supplied with 120VAC 60Hz.

r:J::\ Groundinglnstructions \!!!) The grounding and bonding of the overall system shall be donein accordance with National Electric Code(NEC) and local codes.

PACKAGE CONTENTS

1. OULET BOX (NOT INCLUDED) DRYWALL ANCHOR x 2
2. BLACK SUPPLY WIRE (NOT INCLUDED) MOUNTING BRACKET
3. WHITE SUPPLY WIRE (NOT INCLUDED) FIXTURE MOUNTING SCREW x 2
4. POWER SUPPLY GROUND WIRE (NOT INCLUDED) MOUNTING BRACKET SCREW x 2
5. P4 WIRE NUT x 3 SELF -TAPPING SCREW x 2
6. GROUND FIXTURE WIRE FIXTURE CANOPY
7. BLACK FIXTURE WIRE CANOPY NUT x 2
8. WHITE FIXTURE WIRE LED SHIELD x 3
9. GLASS SHADE x 3

Read More About This Manual & Download PDF:

References

• The leader in LED lighting solutions

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>