ONFORU LED RGB Flood Light User Manual
- June 6, 2024
- ONFORU
Table of Contents
LED RGB FLOOD LIGHT
Product Manual
MODEL:
D100WIFI
G5OWIFI
SAFETY INFORMATION
Disconnect the power supply before attempting any work on the unit!
- Installing these units involves work on the mains voltage supply; installation must therefore be carried out professionally in accordance with the appliance national wiring regulations and electrical operating conditions.
- The product must be installed by a licensed professional electrician.
- Check all components for damage, do not use the product if it is damaged.
- To ensure the product can work normally, please use it in the voltage within the range on the lamp label.
- The floodlight enclosure heats up when the light is on. Please adjust the angle of the light after the power is off for 10-15 minutes. Do not look into the LED light at a short-range or any prolonged period(>5 min).
- Do not install the unit on (normally) flammable surfaces.
- Do not alter or change parts of the light at will, in case of the accidents such as breakage, fall, electric shock, fire, etc.
- Only to be installed outside arm’s reach.
- The light is IP66 waterproof, but the plug is non-waterproof. Please connect the plug indoors or connect to a socket that provides IP65 protection.
- Please use tools to adjust the lights.
- The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced.
NOTE: FCC Warning: Any Changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment. This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. Note:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures: -Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver. -Connect the
equipment into an outlet on a circuit different from that to which the
receiver is connected. -Consult the dealer or an experienced radio/TV
technician for help. This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. This equipment should be
installed and operated with a minimum distance of 20cm between the radiator &
your body.
PARAMETER
| A-330x35x306 mm / 12.99×1.36×12.05 in
B-242x39x256 mm / 9.52×1.53×10.07 in
---|---
| A- 1.74 kg / 3.83 lb
B- 0.8 kg / 1.76 lb
| 100-120V – 60Hz 220-240V – 50Hz
| RGB/2700 — 6500
| I P66
Operating
Temperature| -25°C – 40°C
PAIRING LED LIGHT WITH”SMART LIFE” App.
NOTE: Turn ON/OFF the Smart LED Light three times until the LED light
starts to flash quickly, which indicates the success of the factory reset.
Step 1: “Smart Life” App Download. There are 2 options for obtaining and
downloading the “Smart Life” App on your smart device. 1. Scan the OR code on
the right. 2. Search for “Smart Life” in the App Store or Google Play.
https://smartapp.tuya.com/smartlife
Step 2: Enter the “Smart Life” App. register an account and log in. If you
already have an account for Smart Life App., Please select “Log in with
existing account”. Note: You will need your “Smart Life” App. username and
password to pair with Amazon Alexa and/or Google Assistant. Step 3. Please
turn on the Wi-Fi and Bluetooth before connecting LED lights to the “Smart
Life” APP. Tap the “+” button on the top right corner to add a device, then
tap”lighting device” to enter the next page. Note: This smart LED Light can
only support a 2.4 GHz network and cannot work with a 5.0 GHz network. Please
check if your home network is 2.4 GHz and make sure that your phone has been
connected to your Wi-Fi network. Please ensure your network is not hidden.
Step 4. How to pair the LED Light. 1. Power on the LED Light. 2. Power off it
three times quickly until it flashes, which indicates that the floodlight has
entered pairing mode. 3. Tap the confirmation button to pair the LED Light. 4.
Enter a Wi-Fi password to join your network. Please Note a. This smart LED
Light can only support a 2.4 GHz network and cannot work with a 5.0 GHz
network. b. Please check if your home network is 2.4 GHz and make sure that
your phone has been connected to your Wi-Fi network. Please ensure your
network is not hidden. 5. Wait till it is successfully connected. Note: If
the LED Light is still flashing until the progress map reaches 100%, the
pairing fails, and you will need to repeat the previous 4 steps to pair the
LED Light. Step 5. Name the LED light and tap “Done”. You will find the device
you’ve named is shown on the App homepage. Tap the device to enter the setting
page. You can now control the light with Smart Life App. on this setting page.
Please make sure that your Alexa App. is connected to Amazon Echo, and both
work together successfully under your Wi-Fi network. Step A: Log in your Alexa
App., tap at the top left corner, and tap “Skills”. Step C: Enter your
account and password of Smart Life App., tap “Link Now”, then tap ” Authorize”
on the next page authorize Smart Life Info to Alexa. Note: Same account and
password as Smart Life App.
Step D : Once your Smart Life account is successfully connected to Alexa, the
following r page will pop up. Tap “Done” on top left corner, then tap
“DISCOVER DEVICES” on the next page. Step E : Wait a few seconds for Alexa to
detect the LED Light from Smart Life App., and you will find the device named
“Smart LED Light” has been paired to Alexa App from Smart Life App. After step
E is done, you can now control the light with Alexa App. on this setting page.
A. slide to change brightness B. tap to turn on/off the light C. enter to
change colors
Try these commands and see what happens by asking Alexa: Alexa, turn on
“device name” Alexa, turn off “device name” Alexa, set “device name” to
“color” Alexa, set “device name” to “number” For example: “Alexa, turn on
Smart LED Light”, “Alexa, dim Smart LED Light to 50%” etc.
Note: The device name is the one you give to the LED Light on Smart Life
App. In this user guide, the device is named “Smart LED Light”.
GOOGLE ASSISTANT APP
Step A : Open your Google Home App., tap “Home Control” on the Left Side Bar page. Step B : Tap “+” button on the bottom right corner to enter the next page.
Step: Find “Smart Life ” from the sidebar list.
Step D: Enter your account and password of Smart Life App., tap “Link Now”,
then tap “Authorize” on the next page to authorize your Smart Life Account
Info to Google Home. Note: Same account and password as Smart Life App.
Step E: You will find that Google Home has found the device named “Smart LED
Light” on this page. try these commands and see what happens by asking Google:
ok, Google, turn on “device name” ok, Google, turn off “device name” ok,
Google, set the “device name” to “color ok, Google, set “device name” to
“number For example: “ok Google, turn on Smart LED Light”, “ok Google, dim
Smart LED Light To 50%’ etc. Note: The device name is the one you give to the
LED Light on Smart Life App. In this user guide, the device is named “Smart
LED Light”
COMPONENTS AND STRUCTURE
- Tempered Glass Lid
- LED Light Source
- Lamp Bracket
- Antenna
Note Cord – type Y attachment. For type Y attachment: if the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similarly qualified person in order to avoid a hazard.
Note
- – Make sure that the distance between the light and the object being lit is more than 1 meter, so as to avoid high temperature caused by a short distance.
- – Caution, risk of electric shock.
- – Earth wire is required for connection for electric safety.
- – Lights that are not suitable for covering with thermal insulation materials.
Non-User Replaceable Light Source
The light source contained in this floodlight shall only be replaced by the
manufacturer or his service agent or a similarly qualified person.
Limitation of Indoor and Outdoor Use
- This light is waterproof and dustproof. It is protected against rain, but it cannot be immersed in water.
- The mounting position of this light should be able to bear at least 10 times as heavy as the light.
- This light is powered by a High Voltage Alternating Current (HVAC). It should be connected to the ground wire and kept away from easy reach.
- This light should be used in conditions with sound heat dissipation. The working temperature of it should be less than 40°C. Overhigh working temperature will cause serious lumen depression and affect the lifespan of the light.
- For type Y attachments: If the external flexible cable or cord of this luminance is damaged, it shall be exclusively replaced by the manufacturer or service agent or a similarly qualified person in order to avoid a hazard.
INSTALLATION STEPS
Step 1: According to the spacing (see the “A” part of the picture) of two
screw bits on the LED Light bracket, drill two mounting holes.
Step 2: Put the bracket onto the prepared mounting holes and then screw it on.
Step 3: Adjust the beam direction as you like, and then plug into the main
socket.
OPERATION & MAINTENANCE
- Prior to cleaning the light, make sure it has been disconnected from the power supply.
- The unit is not suitable for burglar alarm systems as it is not tamperproof in the manner prescribed for such systems.
- Never use any chemicals or corrosive substances for cleaning.
DISPOSAL
Electrical and electronic equipment, accessories and packaging must be
recycled in an environmentally compatible manner. Do not dispose of electrical
and electronic equipment as domestic waste.
EU countries only:
Under the current European Directive on Waste Electrical and Electronic
equipment and its implementation in national law, electrical and electronic
equipment no longer suitable for use must be collected separately and recycled
in an environmentally compatible manner.
Manufacturer / Hersteller:
supportoonforuled.com www.onforuleds.com
EU IREP
BellaCocool GmbH Pettenkoferstral3e 18, 10247, Berlin, Germany
support@onforuled.com
1KI REPI
MDH LIGHTING LTD UNIT G25 WATERFRONT STUDIOS 1 DOCK ROAD LONDON UNITED KINGDOM
E16 1AH support@onforuled.com
Made in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>