Fisher AND Paykel OB60SMPTDG1 Built In Oven Installation Guide

Fisher AND Paykel OB60SMPTDG1 Built In Oven

SAFETY AND WARNINGS

WARNING!
Electric Shock Hazard
Failure to follow this advice may result in electric shock or death.

• Before carrying out any work on the electrical section of the appliance, it must be disconnected from the mains electricity supply.
• Connection to a good earth wiring system is essential and mandatory.
• Alterations to the domestic wiring system must only be made by a qualified electrician.

WARNING
Fire Hazard
Failure to follow this advice may result in overheating, burning, and injury.
Do not use adapters, reducers, or branching devices to connect this appliance to the main power supply.

WARNING
Cut Hazard Failure to use caution could result in injury.

• Take care: some edges are sharp.

IMPORTANT!
SAVE THESE INSTRUCTIONS
The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our website www.fisherpaykel.com, or contact your local Fisher & Paykel dealer.

WARNING!
To avoid hazards, follow these instructions carefully before installing or using this appliance.

• Please make this information available to the person installing the appliance—doing so could reduce your installation costs.
• This appliance must be installed and connected to the mains power supply only by a suitably qualified person according to these installation instructions and in compliance with any applicable local building and electricity regulations.
• Failure to install the appliance correctly could invalidate any warranty or liability claims.
• If the power supply cable is damaged, it must be replaced by the manufacturer, its service agent, or a similarly qualified person to avoid a hazard.
• Isolating switch: make sure this oven is connected to a circuit that incorporates an isolating switch providing full disconnection from the power supply by the wiring rules.
• The oven must be earthed.
• Do not use adaptors, reducers, or branching devices to connect the oven to the mains electricity supply, as they can cause overheating and burning.
• The appliance must not be installed behind a decorative door to avoid overheating.
• Please take extra care not to damage the lower trim of the oven during installation. The trim is important for correct air circulation and allows the door to open and close without obstruction.
• The manufacturer does not accept any responsibility for damage resulting from incorrect installation.

BEFORE INSTALLATION

Ensure that

• The countertop and oven cavity are square and level and are the required dimensions.
• The installation will comply with all clearance requirements and applicable standards and regulations.
• The isolating switch will be easily accessible to the customer with the oven installed.
• The electrician provides the sufficient free length of power supply cable to reach from the bottom rear of the cavity to at least 1.5 meters in front of the bottom edge of the opening.
• The cable may enter the cavity from the side, top, or bottom, but the top entry must be at the rear of the cavity.
• The oven connection socket (if fitted) is outside the cavity if the oven is flush to the rear wall.
• The oven will rest on a surface that can support its weight.
• The height of the floor suits the customer.
• You consult local building authorities and by-laws if in doubt regarding installation.

IMPORTANT!
Some environmental factors and cooking habits can cause condensation in and around the oven during use. To protect surrounding cabinetry from possible damage caused by frequent or excessive condensation, we recommend moisture- proofing the oven cavity.

AFTER INSTALLATION

• The oven door can open fully without obstruction.
• The power supply cable does not touch any hot metal parts.
• The isolating switch is easily accessible to the customer with the oven installed.
• You complete the ‘Final checklist’ at the end of the installation.
• If, after following the instructions given, correct performance cannot be achieved, please contact your nearest Fisher & Paykel Authorised Service Centre, Customer Care, or contact us through our local website listed at the end of this document.

INSTALLATION MILESTONES

MILESTONE LINKS

Ensure both hinges are fully locked before shutting the door. Align oven with surrounding cabinetry and appliances.

COMPONENTS

PARTS

TOOLS

PRODUCT DIMENSIONS

Product Dimensions mm

CABINETRY DIMENSIONS

CABINETRY DIMENSIONS MM

• Minimum inside width of cavity 560
• Overall width of cabinetry 600
• Overall height of cabinetry 600
• Minimum inside height of cavity 580
• Minimum inside depth of cavity 550

If installing a cooktop above the oven, ensure adequate clearance is provided as per the cooktop manufacturer’s instructions.

CHECK CAVITY

1. Measure cavity dimensions. Ensure all
2. minimum specifications have been met.
3. Refer to page 6.
4. For consideration and installation, the flashing has
5. Ensure service access complies with local requirements. Refer to page 8 for details.
6. ensure any cooktop ventilation requirements have been considered

UNPACK PRODUCT

• Do not lift or move the product using the handle.
• Keep all packing materials until the unit has been inspected.
• Inspect the product to ensure there is no shipping damage. If any damage is detected contact the dealer or retailer you brought the product from to report the damage.
• Fisher & Paykel is not responsible for shipping damage.

1. Cut all straps and remove the carton top car
2. Lift the carton sleeve and remove any transit packaging.
3. Set aside any accessories.
4. Dispose responsibly.

POSITION OVEN INTO CAVITY

1. Some models only:
2. For dark cabinetry, the supplied trim can be used to enhance the clashing finish.
3. To install, remove the trim adhesive and press to secure to cavity.
4. Lift product into cavity.

REFIT DOOR

1. Holding the door on both sides, carefully lift the door back onto the hinges.
2. Open the door fully push each locking lever down and lock into place.
3. Ensure both hinges are fully locked before shutting the door.

ALIGN AND SECURE

1. Align oven with surrounding cabinetry and appliances.
2. Using the product as a guide, pre-drill 2
3. 3mm pilot holes.
4. Secure oven to cavity using the 2 x 7×13 pan head screws provided.

REFIT SHELVES
Silains shelves

• Place serves back Into the oven at the desired level.
• ensure services are level and correct. positioned with the guard fall at the back. wire shelves
• Slide shelves into the cavity.
• clip on silane snel supports to ensure the sides are positioned the correct
• Way around, with the triangular tao at the front
• “it the too clios over the side rack. Ine front clip should be fitted as close to the front of the side rack as possible. Make sure the rear clip is engaged.
• Click the bottom clips into place.

TEST OVEN
Follow the guidance on the screen to ensure the oven turns on and heats correctly. Refer to your User Guide for more information.

INSTALLER CHECKLIST
TO BE COMPLETED BY THE INSTALLER

Ensure the oven is level and securely fitted to the cabinetry. Check the lower trim is undamaged. Open the oven door slowly until it is fully open and check there is adequate clearance between the bottom of the door and the lower trim. This is to ensure correct air circulation. Should the lower trim become damaged, straighten the trim and ensure the oven door opens fully without obstruction. Ensure you remove all internal packaging (including the circular yellow packing retainers molding me accessory box in place. Ensure all oven vents and openings are clear and free of any obstruction or damage. Failure to make sure all oven vents are clear may result in poor product performance. ensure une Isolaung switch is accessible oy une customer.

Fisher & Paykel Appliances 2024. All rights reserved. The models shown in this guide may not be available in all markets and are subject to change at any time. The product specifications in this guide apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time. For current details about model and specification availability in your country, please go to our website or contact your local Fisher & Paykel dealer.

References

• Shop Luxury Kitchen Appliances | Fisher & Paykel United Kingdom
• Shop Luxury Kitchen Appliances | Fisher & Paykel Australia

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>