Eterna KCIRMW Colour Temperature Selectable Circular LED Ceiling Wall Light With Microwave Sensor Instruction Manual

Eterna KCIRMW Colour Temperature Selectable Circular LED Ceiling Wall

Light With Microwave Sensor Instruction Manual

Model: KCIRMW

These instructions are provided as a guideline to assist you.
PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION AND RETAIN FOR FUTURE REFERENCE

Pack contents:
1 x LED ceiling fitting

READ THIS FIRST:

Check the pack and make sure you have all of the parts listed on the front of this booklet. If not, contact the outlet where you bought this product.

This product must be installed by a competent person in accordance with the current building and IEE wiring regulations.

As the buyer, installer and/or user of this product it is your own responsibility to ensure that this fitting is fit for the purpose for which you have intended it. Eterna Lighting cannot accept any liability for loss, damage or premature failure resulting from inappropriate use.

This product is designed and constructed according to the principles of the appropriate British Standard and is intended for normal domestic service. Using this fitting in any other environments may result in a shortened working life, for example where there is prolonged periods of use or higher than normal ambient temperatures such as lighting public or shared spaces or in nursing /care home facilities.

Switch off the mains before commencing installation and remove the appropriate circuit fuse or lock off MCB.

This product is suitable for use in living areas, Bathroom Zone 2 and outsides of zones.

If being fitted in a bathroom a 30mA RCD must be used.

This product is designed for permanent connection to fixed wiring: this must be a suitable circuit (protected with the appropriate MCB or fuse).

This product is suitable for installation on surfaces with normal flammability e.g. wood, plasterboard and masonry.

It is not suitable for use on highly flammable surfaces (e.g. polystyrene, textiles).

Before making fixing hole(s), check that there are no obstructions hidden beneath the mounting surface such as pipes or cables.

NOTE: In warm white (3000K) and daylight white (6000K) operation only one set of LEDs will illuminate, in cool white (4200K) both sets of LEDs will illuminate.

INSTALLATION:

Choose the location for your new fitting according to the conditions listed opposite.

1. Hold the base of the fitting and gently turn the diffuser and decorative trim anti-clockwise and lift off.

2. Loosen screw on LED turnbuckle and rotate to release the tray which will then hinge to allow access to the wiring terminals.

3. Drill holes in the back of your fitting for your fixing screws, take care and drill gently to ensure a clean hole through. Use a drill bit sized appropriately to your fixing screws.

4. Using the back of your fitting as a template, mark the position of your fixing holes on your mounting surface.

5. Prepare the holes in your mounting surface as appropriate for your fixings.

6. Pierce the rubber grommet in the back of your fitting making a hole just large enough to make a tight fit around the incoming mains cable.

7. Thread the cable through the grommet and offer the fitting to the ceiling / wall.

8.  Secure the fitting in place. Note, if protection against ingress of moisture is required, the heads of screws must be covered with a silicone or similar sealant.

9. Check that the grommet is still correctly fitted in the cable entry hole and around the incoming cable.

10. Make the electrical connections to the terminal block according to the markings:
    Brown to live (L)
    Blue to neutral (N)

11. Set colour temperature to the desired option by selecting appropriate switch setting on the driver.

12. Set desired settings on microwave.
13. Replace gear tray and secure in position.
14. Offer the diffuser and decorative trim onto the top of the fitting and turn clockwise until they are held securely.
15. Restore the power and switch on.

UNDERSTANDING THE CONTROLS:

REFER TO MICROWAVE SENSOR PICTURE OPPOSITE
The sensor is an active motion detector: it emits a high frequency electromagnetic wave 5.8GHz and receives its echo. The sensor detects the change in echo from movement in its detection zone. A microprocessor then triggers the switch light ON command. Detection is possible through doors, panels of glass and thin walls.

DETECTION RANGE:
This determines the effective range of the motion detector and is set up by DIP switches at the sensor itself, refer to figure. Note that reducing the sensitivity will also narrow the detection range.

HOLD TIME:
This determines the time the fitting remains at 100% level on motion detection and is set with DIP switches at the sensor itself, refer to figure. The walk test setting is useful when installing the fitting to establish correct operation and range.

DAYLIGHT SENSOR:
This setting holds off the 100% light output should there be sufficient daylight and is set using DIP switches at the sensor, refer to figure.

• If the daylight sensor is disabled the sensor will turn on light once motion is detected regardless of ambient light level.

An Earth connection is not required for the operation of these Class II luminaires. The addition of the Earth terminal provides a loop-in/loop out facility which allows connectivity through to other Class I luminaires in the same lighting circuit.

MICROWAVE SENSOR SPECIFICATIONS:

Eterna Lighting Ltd
RED DIRECTIVE – Microwave Occupancy Sensor
Full declaration available at:
www.eterna-lighting.co.uk/red-declaration

LAMP REPLACEMENT:

The light source is designed to last the lifetime of the luminaire.

The light source contained in this luminaire shall only be replaced by the manufacturer, service agent or a similar qualified person.
CAUTION, RISK OF ELECTRIC SHOCK.

EVENTUALLY, YOU MAY WANT TO REPLACE THIS PRODUCT:
Regulations require the recycling of Waste from Electrical and Electronic Equipment (European
“WEEE Directive” effective August 2005—UK WEEE Regulations effective 2nd January 2007). Environment Agency Registered Producer: WEE/GA0248QZ.

WHEN YOUR PRODUCT COMES TO THE END OF ITS LIFE OR YOU CHOOSE TO REPLACE IT, PLEASE RECYCLE IT WHERE FACILITIES EXIST – DO NOT DISPOSE WITH HOUSEHOLD WASTE.

CLEANING:

Clean this fitting only with a soft dry cloth.
Do not use any chemical or abrasive cleaners.

LED LAMP SPECIFICATIONS:

IF YOU EXPERIENCE PROBLEMS:
If you believe your product is defective, please return it to the place where you bought it. Our Technical Team will gladly advise on any Eterna Lighting product, but may not be able to give specific instructions regarding individual installations.

Email: sales@eterna-lighting.co.uk / technical@eterna-lighting.co.uk
Visit website: www.eterna-lighting.co.uk

Made in China

Read More About This Manual & Download PDF:

References

• Lighting.Co.Uk domain name is for sale. Inquire now.
• red-declaration - ETERNA LIGHTING

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>