Eterna BATLED4FT 5ft and 6ft High Output LED Battens Instruction Manual

June 4, 2024
Eterna

INSTALLATION INSTRUCTIONS
A guide for qualified electricians

Model:
4ft, 5ft & 6ft Standard LED Battens
BATLED4FT / BATLED5FT / BATLED6FT
5ft & 6ft High Output LED Battens
BATLED5HO / BATLED6HO
These instructions are provided as a guideline to assist you.
PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION
AND RETAIN FOR FUTURE REFERENCE

BATLED4FT 5ft and 6ft High Output LED Battens

Pack contents:
1 x Fitting
1 x Fixing kit

SPECIFICATIONS

Check the pack and make sure you have all of the parts listed on the front of this booklet. If not, contact the outlet where you bought this product.
This product must be installed by a competent person in accordance with the current building and IEE wiring regulations.
As the buyer, installer, and/or user of this product it is your own responsibility to ensure that this fitting is fit for the purpose for which you have intended it. Eterna Lighting cannot accept any liability for loss, damage or premature failure resulting from inappropriate use.
This product is designed and constructed according to the principles of the appropriate British Standard and is intended for normal domestic service. Using this fitting in any other environment may result in a shortened working life, for example where there is higher than normal ambient temperatures.
Switch off the mains before commencing installation and remove the appropriate circuit fuse or lock off MCB.
This unit is suitable for indoor use only.
This product is suitable for use in living areas, and bathroom dry (outside) zones only (see diagram below and current IEE Wiring Regulations for details). It is not suitable for bathroom zones 0, 1, 2, or other areas where contact with moisture is likely. If being fitted in a bathroom a 30mA RCD must be used.

This product is designed for permanent connection to fixed wiring: this must be a suitable circuit (protected with the appropriate MCB or fuse).
This product is suitable for installation on surfaces with normal flammability e.g. wood, plasterboard, and masonry. It is not suitable for use on highly flammable surfaces (e.g. polystyrene, textiles).
Before making fixing the hole(s), check that there are no obstructions hidden beneath the mounting surface such as pipes or cables.
Make sure that the fixings are strong enough to support the weight of the fitting and hold it rigidly.
The chosen location of your new fitting should allow for the product to be securely mounted (e.g. to a ceiling joist) and safely connected to the mains supply (lighting circuit). When choosing the location for your new fitting, ensure that the fixings will be anchored in a solid surface e.g. concrete, brick, or a joist – do not fix directly onto paneling, cladding, plasterboard, etc.
Do not attach to surfaces that are damp, freshly painted, or otherwise electrically conductive (e.g. metallic surfaces).
When making connections ensure that the terminals are tightened securely and that no strands of wire protruding. Check that the terminals are tightened onto the bared conductors and not onto any insulation.
This product must be connected to earth termination.
This product is not intended to be used by children and persons with sensory, physical, and/or mental impairments that would prevent them from using it safely.
Small children should be supervised to ensure that they do not play with this appliance.
You are advised at every stage of your installation to double-check any electrical connections you have made. After you have completed your installation there are electrical tests that should be carried out, these tests are specified in the current IEE wiring and building regulations.

LAMP REPLACEMENT

The light source is designed to last the lifetime of the luminaire.
The light source contained in this luminaire shall only be replaced by the manufacturer, service agent, or a similarly qualified person.
CAUTION, RISK OF ELECTRIC SHOCK.

INSTALLATION

  1. Choose the location of your new fitting giving consideration to all of the conditions listed above and the position of the entry points for the mains cable supply.

  2. Carefully detach the LED tray from the main housing.

  3. Unclip the gear tray retaining straps, disconnect the driver plug and detach the earth spade; set the LED tray aside.

  4. Using the back of the fitting as a template, mark the location of the fixing holes on your mounting surface.

  5. Thread the supply cable through the large grommet hole in the back of the fitting.

  6. Secure the fitting in place using suitable fixings and ensure that cables are not trapped behind or inside the fitting.

  7. Make the connections of the supply cable to the terminals inside the fitting following the color
    coding below:
    Neutral – Blue
    Earth – Green, and Yellow
    Live – Brown

  8. Clip the gear tray retaining straps back to the LED tray, re-connect the driver plug to the tray and re-attach the earth spade.

  9. Attach the LED tray, taking care that no cables are trapped between the tray and housing.

  10. Restore power and switch on.

LED LAMP SPECIFICATIONS:| 4FT| 5FT| 6FT| 5FT HIGH OUTPUT| 6FT HIGH OUTPUT
---|---|---|---|---|---
Luminaire lumens (with diffuser)| 2950 lm| 4750 lm| 6050 lm| 7550 lm| 8450 lm
Lumens from the chip (no diffuser)| 3400 lm| 5500 lm| 7000 lm| 8700 lm| 9750 lm
Useful lumens| 2850 lm| 4600 lm| 5800 lm| 7300 lm| 8200 lm
Rated Wattage| 23W| 38W| 48W| 60W| 65W
Rated luminous flux| 2850 lm| 4600 lm| 5800 lm| 7300 lm| 8200 lm
A nominal lifetime of the lamp| 35,000 hrs| 35,000 hrs| 35,000 hrs| 35,000 hrs| 35,000 hrs
Color temperature| 4200K| 4200K| 4200K| 4200K| 4200K
Number of switching cycles before premature lamp failure| >15,000| >15,000|

15,000| >15,000| >15,000
Warm-up time up to 60% of the full light output| Instant full light| Instant full light| Instant full light| Instant full light| Instant full light
Dimmable| No| No| No| No| No
Nominal beam angle| 120°| 120°| 120°| 120°| 120°
Rated power| 23W| 38W| 48W| 60W| 65W
Rated lamp lifetime| 35,000 hrs| 35,000 hrs| 35,000 hrs| 35,000 hrs| 35,000 hrs
Displacement factor| 0.91| 0.97| 0.98| 0.98| 0.98
Lumen maintenance factor at end of nominal life| ≥0.70| ≥0.70| ≥0.70| ≥0.70| ≥0.70
Starting time| <0.1s| <0.1s| <0.1s| <0.1s| <0.1s
Color rendering| ≥80| ≥80| ≥80| ≥80| ≥80
Colour consistency| Within a six-step Macadam ellipse| Within a six-step Macadam ellipse| Within a six-step Macadam ellipse| Within a six-step Macadam ellipse| Within a six-step Macadam ellipse
Rated peak intensity| 940cd| 1530cd| 1937cd| 2418cd| 2721cd
Rated beam angle| 120°| 120°| 120°| 120°| 120°
Voltage / Frequency| 240V~50Hz| 240V~50Hz| 240V~50Hz| 240V~50Hz| 240V~50Hz
Lumen efficacy| 128 lm / W| 125 lm / W| 126 lm / W| 126 lm / W| 130 lm / W
Not suitable for accent lighting

Eterna BATLED4FT 5ft and 6ft High Output LED Battens -
2

| |
---|---|---
https://www.eterna-lighting.co.uk/product/BATLED4FT/| https://www.eterna- lighting.co.uk/product/BATLED5FT/| https://www.eterna- lighting.co.uk/product/BATLED6FT/

Eterna BATLED4FT 5ft and 6ft High Output LED Battens -
3

| Eterna BATLED4FT 5ft and 6ft High Output LED Battens - qr
code6|
---|---|---
https://eprel.ec.europa.eu/qr/801228| https://eprel.ec.europa.eu/qr/801254| https://eprel.ec.europa.eu/qr/801293

Eterna BATLED4FT 5ft and 6ft High Output LED Battens -
4

Eterna BATLED4FT 5ft and 6ft High Output LED Battens - qr
code4| | | Eterna BATLED4FT 5ft and
6ft High Output LED Battens - qr code1
---|---|---|---
https://www.eterna-lighting.co.uk/product/BATLED5HO/| https://eprel.ec.europa.eu/qr/801284| https://www.eterna- lighting.co.uk/product/BATLED6HO/| https://eprel.ec.europa.eu/qr/801303

EVENTUALLY, YOU MAY WANT TO REPLACE THIS PRODUCT:
Regulations require the recycling of Waste from Electrical and Electronic Equipment (European “WEEE Directive” effective August 2005—UK WEEE Regulations effective 2nd January 2007). Environment Agency Registered Producer: WEE/ GA0248QZ.
WHEN YOUR PRODUCT COMES TO THE END OF ITS LIFE OR YOU CHOOSE TO REPLACE IT, PLEASE RECYCLE IT WHERE FACILITIES EXIST – DO NOT DISPOSE OF IT WITH HOUSEHOLD WASTE.

CLEANING:
Disconnect the power and clean the exterior only of this fitting with a soft dry cloth. Do not use any chemical or abrasive cleaners.

IF YOU EXPERIENCE PROBLEMS:

If you believe your product is defective, please return it to the place where you bought it. Our Technical Team will gladly advise on any Eterna Lighting product, but may not be able to give specific instructions regarding individual installations.

See the website for more information on replaceability and recycling

Email:sales@eterna-lighting.co.uk
technical@eterna-lighting.co.uk
Visit our website:www.eterna-lighting.co.uk
Issue 0821
Made in China

Documents / Resources

| Eterna BATLED4FT 5ft and 6ft High Output LED Battens [pdf] Instruction Manual
BATLED4FT, BATLED5FT, BATLED6FT, BATLED4FT 5ft and 6ft High Output LED Battens, BATLED4FT, 5ft and 6ft High Output LED Battens, High Output LED Battens, LED Battens, Battens
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Eterna User Manuals

Related Manuals