Eterna BH100E27 Bulkhead with E27 Lamp holder Instruction Manual

: June 3, 2024
: Eterna

Table of Contents

READ THIS FIRST
INSTALLATION
LAMP REPLACEMENT
REPLACEMENT LAMP TYPE
EVENTUALLY, YOU MAY WANT TO REPLACE THIS PRODUCT
CLEANING
IF YOU EXPERIENCE PROBLEMS
Support
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Eterna BH100E27 Bulkhead with E27 Lamp holder Instruction Manual

READ THIS FIRST

Check the pack and make sure you have all of the parts listed on the front of this booklet. If not, contact the outlet where you bought this product.

This product must be installed by a competent person in accordance with the current building and IEE wiring regulations.

As the buyer, installer and/or user of this product it is your own responsibility to ensure that this fitting is fit for the purpose for which you have intended it. Eterna Lighting cannot accept any liability for loss, damage or premature failure resulting from inappropriate use.

This product is designed and constructed according to the principles of the appropriate British Standard and is intended for normal domestic service. Using this fitting in any other environments may result in a shortened working life, for example where there is prolonged periods of use or higher than normal ambient temperatures.

The lifetime of compact fluorescent lamps and ballasts are negatively affected by increased switching i.e. where a PIR is being used to control the fitting.

Switch off the mains before commencing installation and remove the appropriate circuit fuse or lock off MCB.

This unit is suitable for outdoor use.

This product is designed for permanent connection to fixed wiring: this must be a suitable circuit (protected with the appropriate MCB or fuse).

This product is suitable for installation on surfaces with normal flammability e.g. wood, plasterboard and masonry. It is not suitable for use on highly flammable surfaces (e.g. polystyrene, textiles).

Before making fixing hole(s), check that there are no obstructions hidden beneath the mounting surface such as pipes or cables.

Make sure that the fixings are strong enough to support the weight of the fitting and hold it rigidly.

The chosen location of your fitting should allow for the product to be securely mounted and anchored to a solid surface e.g. concrete, brick or a joist—do not fix directly onto panelling, cladding, plasterboard etc.

Make connections to the electrical supply in accordance with the following code:
Live: Brown or Red
Neutral: Blue or Black

When working at heights ensure you use a suitable platform.

When making connections ensure that the terminals are tightened securely and that no strands of wire protrude. Check that the terminals are tightened onto the bared conductors and not onto any insulation.

This product must NOT be connected to earth termination.

This product is not intended to be used by children and persons with sensory, physical and/or mental impairments that would prevent them from using it safely.

You are advised at every stage of your installation to double-check any electrical connections you have made. After you have completed your installation there are electrical tests that should be carried out, these tests are specified in the current IEE wiring and building regulations.

INSTALLATION

Choose the location for your new light fitting giving consideration to the points listed opposite.
Remove the diffuser by removing the two retaining screws and lifting off.
Drill out four fixing holes in the back of the fitting according to your chosen fixing method. Four holes have been part made in the feet of the fitting to enable the fitting to be secured to a solid surface.
Choose the point for cable entry and remove the corresponding knock-out.
Using the fitting as a template, mark the location of your fixing holes on the mounting surface.
Secure the fitting in position using suitable fixings (not supplied).
Cover the heads of the screws with silicone sealant (not supplied).
Pierce one of the rubber grommets and thread your supply cable through. The grommet should be a tight fit on the cable to ensure a waterproof seal. Fit the grommet into your chosen entry point in the case.
Thread the supply cable into the fitting, if your cable enters from the top of the fitting, route it underneath the reflector, away from the heat ofthe lamp.
Make the electrical connections according to the colour code listed opposite and noting the terminal identification in the fitting.
Pull any excess cable back through the grommet but do not pull the cable tight.
Insert a lamp observing the maximum wattage and lamp type marked on the lampholder and listed on the back of this leaflet.
Replace the diffuser and tighten the two screws. Take care not to over-tighten.
Restore the power and switch on.

LAMP REPLACEMENT

Switch off the electricity at the mains.
Undo the two screws and remove the diffuser.
Remove and replace lamp making sure it is of the same type and wattage as stated on the re lamping label.
Replace the diffuser and tighten the two screws. Ensure that the gasket is correctly fitted between the diffuser and the back.

REPLACEMENT LAMP TYPE

Requires 1 x suitable ES (E27) energy saving lamp (not included).
Fitting is rated at 100W max.

EVENTUALLY, YOU MAY WANT TO REPLACE THIS PRODUCT

Regulations require the recycling of Waste from Electrical and Electronic Equipment (European “WEEE Directive” effective August 2005—UK WEEE Regulations effective 2nd January 2007). Environment Agency Registered Producer: WEE/ GA0248QZ.

WHEN YOUR PRODUCT COMES TO THE END OF ITS LIFE OR YOU CHOOSE TO REPLACE IT, PLEASE RECYCLE IT WHERE FACILITIES EXIST – DO NOT DISPOSE WITH HOUSEHOLD WASTE.

CLEANING

Disconnect the power and clean the exterior only of this fitting with a moist (not wet) cloth.

The diffuser may be removed and washed in a mild detergent solution. Make sure the diffuser is completely dry before putting it back on your light fitting.

Do not use any chemical or abrasive cleaners.

IF YOU EXPERIENCE PROBLEMS

If you believe your product is defective, please return it to the place where you bought it. Our Technical Team will gladly advise on any Eterna Lighting product, but may not be able to give specific instructions regarding individual installations.

Symbols: