OPT7 Aura Aluminum Underglow Lighting Kit Instruction Manual

June 13, 2024
OPT7

UNDERBODY
WITH UNLOCK & DOOR ASSIST /8PC
INSTALLATION GUIDE

MAIN COMPONENTS

OPT7 Aura Aluminum Underglow Lighting Kit - COMPONENTS

INSTALLATION

OPT7 Aura Aluminum Underglow Lighting Kit -
INSTALLATION STEP 1
Decide where to locate the control box and ensure wiring has enough length for light bars to be installed in desired location.
IMPORTANT:
The control box must be installed inside the vehicle as it is not waterproof. Avoid installation areas of the engine bay + heated surfaces.
As shown below, connect all the LED bars to the control box with the included extension cables.OPT7 Aura Aluminum Underglow Lighting Kit - INSTALLATION
1 IMPORTANT:
The extension wires are on the led bar. Lay out the bars to measure the length prior to install for a successful installation.
4 × 24” LED Bar + 8ft extension wire
2 × 18” LED Bar + 18ft extension wire
2 × 18” LED Bar + 8ft extension wireOPT7 Aura Aluminum Underglow Lighting
Kit - INSTALLATION 2 WARNING

  1. Connecting to more than 10 AMP will override the kit and cause early failure, ensure it is 10AMPs or less!!
  2. Please ensure that the LED bars or strips/control box/wiring all are mounted in areas where will not exceed 85 °C or 185 °F .

HOW TO CONNECT POWER HARNESS TO YOUR VEHICLE

  • Connect the Red line(+) of power hareness to the vehicle battery’s positive terminal.
  • Connect the Black line (-) of power hareness to the vehicle battery’s negativeterminal or an unpainted area on your vehicle’s frame.

OPT7 Aura Aluminum Underglow Lighting Kit - INSTALLATION
3 STEP 2
Secure Control box in desired location with Velcro or zipties.

  • CONTROL BOX NOT WATERPROOF
    Ensure the control box is safely and securely hidden from exposing elements of moisture.OPT7 Aura Aluminum Underglow Lighting Kit - INSTALLATION
4 STEP 3
    Secure the light bars using the zip ties to tie all the wiring away from the moving components.
    STEP 4 Using the included E-Z Remote, select your desired color or pattern.

OPT7 Aura Aluminum Underglow Lighting Kit - INSTALLATION
5www.OPT-7.COM

AUX WIRING FOR A DOOR/DOME LIGHT

OPT7 Aura Aluminum Underglow Lighting Kit - QR Codehttp://qr.w69b.com/g/pa9DknB6g

Please scan to see a detail instruction on Door Assist Sync or go to https://wintis.ladesk.com/549690-AURA-Door-AssistAUX-Installation-Guide
CONTROL WIRE FOR A DOOR UNLOCK LIGHT
Please make sure the control wire (wire with the yellow sticker) is connected to an “ACC/On” power source(SEE METHOD I FOR DETAILS) ; otherwise,when unlocking it with the car keyfob, It will not trigger any light effects!!
NOTE : When remote unlock feedback is enabled, it am

METHOD : 1

OPT7 Aura Aluminum Underglow Lighting Kit - INSTALLATION
6 STEP
1Open the driver’s door. Then find the door access system control harness that connects between the door frame and the door.
STEP 2
Pull off the harness cover and find the trigger wire that activates the door lock/unlock.OPT7 Aura Aluminum Underglow Lighting Kit - INSTALLATION
7 IMPORTANT
HOW TO DIAGNOSE THE CORRECT TRIGGER WIRE?
First, you must prepare a multimeter. Next, please press the “Lock/Unlock” button on the car keyfob to find out this signal source, this measurement process may take you a little time, but it will ensure that you find the correct signal you need.OPT7 Aura Aluminum Underglow Lighting Kit -
INSTALLATION 8

STEP 3
Connect the control wire (red) to the trigger wire. Then connect the light bar to the control box and use the car keyfob for a final test.
METHOD : 2OPT7 Aura Aluminum Underglow Lighting Kit - INSTALLATION
9 STEP 1
Confirm if the DRL is still on after unlock the vehicle .OPT7 Aura Aluminum
Underglow Lighting Kit - INSTALLATION 10 STEP 2
Confirm if the DRL is halogen lamp .
IMPORTANT
DRL has to be an independent signal, it cannot be a shared signal with fog light, high beam, parking light or turn light.OPT7 Aura Aluminum Underglow
Lighting Kit - INSTALLATION 11 STEP 3
Open the engine room and find the positive wire of the DRL.
IMPORTANT
HOW TO DIAGNOSE THE CORRECT POSITIVE WIRE OF DRL ?
First, please prepare a multimeter.
Next, press the “Lock/Unlock” button on the key fob to find the signal source, then find out the positive wire .
STEP 4
Connect the trigger wire (red) that is on the control box to the DRL positive wire, then connect the LED strip to test if it works.OPT7 Aura Aluminum
Underglow Lighting Kit - INSTALLATION 12

DISCLAIMER

OPT7 Lighting is not liable for damages or personal injuries while installing this product. The Installation Guide is intended as assistance to reduce setup time.
OPT7 Lighting assumes no responsibility for improper installation.
If you are unfamiliar with your vehicle or inexperienced with aftermarket upgrades, please seek professional assistance.
OPT7 recommends installation for safety and guidance.
Modified installations or installation recommendations not specified by OPT7 Lighting will void product warranty.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals