FORTIN 34031 2015 Honda CR V Push Button Remote Starters and Alarm Systems Installation Guide
- June 13, 2024
- FORTIN
Table of Contents
GUIDE # 34031
REGULAR INSTALLATION
ADDENDUM – SUGGESTED WIRING CONFIGURATION
34031 2015 Honda CR V Push Button Remote Starters and Alarm Systems
| VEHICLE | YEARS |
|---|
HONDA
CR-V
Push-to-Start (AT)| 2015-2016
Vehicle functions supported in this diagram (functional if equipped)
- Immobilizer bypass
- T-Harness available (sold separately)
- Arm
- Disarm
- Trunk (open)
- Horn
- Tachometer
- Door Status
- Trunk Status
- Hood Status*
- Hand-Brake Status
- Foot-Brake Status
- Push-to-Start Control
- OEM Remote monitoring
- R.S. OEM remote
Stand Alone compatible
| BYPASS FIRMWARE VERSION
73.[38] HONDA/ACURA MINIMUM| To add the firmware version and the options, use
the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.
---|---|---
| Program bypass option:| UNIT OPTION| DESCRIPTION
---|---|---|---
C1| OEM Remote status (Lock/Unlock) monitoring
| | D6| Push-to-Start
Program bypass option
(If equiped with OEM alarm):| D2| Unlock before / Lock after (Disarm OEM
alarm)
IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:| | Hood trigger
(Output Status).
| Program remote starter option for R.S. OEM REMOTE STAND ALONE:|
FUNCTION| MODE| DESCRIPTION
---|---|---|---|---
38| 2| Enable
Press 3x Lock to remote start with the OEM remote.
MANDATORY INSTALL
*HOOD PIN
HOOD STATUS : THE HOOD PIN SWITCH (INCLUDED) MUST BE INSTALLED IF THE VEHICLE
CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.
SECURITY STICKER
WARNING
…………
Included
Notice: the installation of safety elements are mandatory. The hood pin
and the sticker are essential security elements and must be installed.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION
CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.
DESCRIPTION
AUTOMATIC TRANSMISSION WIRING CONNECTION
DCRYPTOR PROGRAMMING PROCEDURE
BEFORE PROGRAMMING SET THE UNIT OPTIONS AND SAVE.
| Press and hold the programming
button:
Connect the 6-PIN Main harness (White connector).
The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate.
---|---
| Release the programming button
when the Blue & Red LEDs are ON.
If the Blue & Red LEDs are not ON solid disconnect the 6-PIN Data-Link and go
back to step 1.
| Connect the required remaining
harnesses.
| Press and release the
programming button three times (3x).
The Red and Blue LEDs will alternate between 2 flashes and a pause.
| Do not press the brake pedal.
Press the Push-to-Start button twice to turn ON the ignition.
Wait for the Yellow Led to flash rapidly.
Wait for the Blue LED to flash rapidly.
| Press the Push-to-Start button
once to turn off the ignition.
The Red and Yellow LEDs will start flashing alternatively.
| Disconnect all connectors and
after the 6-Pin (Main-Harness) or the 4-Pin Data-link connector.
| Use the tool:
FLASH LINK UPDATER or FLASH LINK MOBILE to visit the DCryptor menu.
*Parts required (not included)
| AFTER DCRYPTOR PROGRAMMING
COMPLETED
Go back to the vehicle and reconnect the 6-Pin (MainHarness) or the 4-pins
(Data-Link) connector and after all the remaining connector.
The module is now programmed.
REMOTE STARTER / ALARM VERIFICATION PROCEDURE
Test the remote starter. Remote start the vehicle.
REMOTE STARTER PROGRAMMING PROCEDURE
REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE STARTER PROGRAMMING.
REMOTE STARTER FUNCTIONALITY
Notice: Updated Firmware and Installation Guides
Updated fi rmware and installation guides are posted on our web site on a
regular basis. We recommend that you update this module to the latest fi rmware
and download the latest installation guide(s) prior to the installation of
this product.
WARNING
The information on this sheet is provided on an (as is) basis with no
representation or warranty of accuracy whatsoever. It is the sole
responsibility of the installer to check and verify any circuit before
connecting to it. Only a computer safe logic probe or digital multimeter
should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or
responsibility whatsoever pertaining to the accuracy or currency of the
information supplied. The installation in every case is the sole
responsibility of the installer performing the work and FORTIN ELECTRONIC
SYSTEMS assumes no liability or responsibility whatsoever resulting from any
type of installation, whether performed properly, improperly or any other way.
Neither the manufacturer or distributor of this module is responsible of
damages of any kind indirectly or directly caused by this module, except for
the replacement of this module in case of manufacturing defects. This module
must be installed by qualifi ed technician. The information supplied is a guide
only. This instruction guide may change without notice. Visit
www.fortinbypass.com to get the latest
version.
Copyright © 2006-2018, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT
PENDING
This guide may change without notice. See
www.fortin.ca for latest version.
TECH SUPPORT
Tel: 514-255-HELP (4357)
1-877-336-7797
**ADDENDUM
GUIDE
www.fortinbypass.com
WEB UPDATE
REV.: 20211110**
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>