milwaukee HD18 JSB Heavy Duty Body Grip Jigsaw Instruction Manual
- June 10, 2024
- Milwaukee
Table of Contents
Nothing but HEAVY DUTY.®
HD18 JSB
Original instructions
HD18 JSB Heavy Duty Body Grip Jigsaw
Picture section with operating description and functional description
Remove the battery pack before starting any work on the machine.
Press the saw blade into the Fixtec holder up to the stop.
In case the base plate can’t be tensioned anymore after frequent adjusting, the base plate setting mechanism can be re-adjusted.
Startup protection:
When switched on, the machine will not start up after the battery is inserted
again.
To continue working, switch the machine off and then on again.
Load-dependent motor protection:
If the motor is overloaded, the overload protection will trip. To continue
working, switch the machine off and then on again.
TECHNICAL DATA
CORDLESS JIGSAW
HD18 JSB
Production code ……………………………………………………..4030 38 05……000001-999999
Battery voltage …………………………………………………………18 V
Stroke rate under no-load
1st gear ……………………………………………………………………..2050 min-1
2nd gear…………………………………………………………………….2700 min-1
Lengths of stroke………………………………………………………26 mm
Bevel cuts up to ………………………………………………………..45°
Cutting depth max. in:
Wood ………………………………………………………………………..120 mm
Steel ………………………………………………………………………….10 mm
Aluminium ………………………………………………………………..30 mm
Weight according EPTA-Procedure 01/2014 ……………2,9 kg
Recommended ambient operating temperature ………..-18…+50 °C
Recommended battery types …………………………………….M18B2, M18B4, M18B5, M18B6, M18B9
Recommended charger ……………………………………………..M12-18C, M12-18AC, M12-18FC, M1418C6
Noise/vibration information
Measured values determined according to EN 62841.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) …………82,5 dB (A)
Sound power level (Uncertainty K=3dB(A)) …………….93,5 dB (A)
Wear ear protectors!
Total vibration values (vector sum in the three axes) determined according to
EN 62841.
Cutting boards 1
Vibration emission value ah,B…………………………………….6,3 m/s 2
Uncertainty K……………………………………………………………..1,5 m/s 2
Cutting sheet metal 2
Vibration emission value ah,M…………………………………….6,4 m/s-2
Uncertainty K……………………………………………………………..1,5 m/s-2
1 with saw blade T101B, dimension 75 x 8 x 1,4 mm and tooth pitch 2,5 mm
2 with saw blade T118A, dimension 55 x 8 x 1 mm and tooth pitch 1,2 mm
WARNING
The vibration and noise emission level given in this information sheet has
been measured in accordance with a standardized test given in EN 62841 and may
be used to compare one tool with another. It may be used for a preliminary
assessment of exposure.
The declared vibration and noise emission level represents the main
applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration
and noise emission may differ. This may significantly increase the exposure
level over the total working period.
An estimation of the level of exposure to vibration and noise should also take
into account the times when the tool is switched off or when it is running but
not actually doing the job. This may significantly reduce the exposure level
over the total working period.
Identify additional safety measures to protect the operator from the effects of
vibration and/or noise such as: maintain the tool and the accessories, keep
the hands warm, organization of work patterns.
WARNING Read all safety warnings, instructions, illustrations and
specifications provided with this power tool. Failure to follow all
instructions listed below may result in electric shock, fi re and/or serious
injury.
Save all warnings and instructions for future reference.
JIG SAW SAFETY WARNINGS
Hold the power tool by insulated gripping surfaces, when performing an
operation where the cutting accessory may contact hidden wiring.
Cutting accessory contacting a “live” wire may make exposed metal parts of the
power tool “live” and could give the operator an electric shock.
Use clamps or another practical way to secure and support the workpiece to a
stable platform.
Holding the workpiece by hand or against your body leaves it unstable and may
lead to loss of control.
Wear ear protectors. Exposure to noise can cause hearing loss.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when working with the
machine. The use of protective clothing is recommended, such as dust mask,
protective gloves, sturdy non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to health. Do not inhale
the dust. Wear a suitable dust protection mask.
Do not machine any materials that present a danger to health (e.g. asbestos).
Switch the device off immediately if the insertion tool stalls! Do not switch
the device on again while the insertion tool is stalled, as doing so could
trigger a sudden recoil with a high reactive force. Determine why the
insertion tool stalled and rectify this, paying heed to the safety
instructions.
The possible causes may be:
-
it is tilted in the workpiece to be machined
-
it has pierced through the material to be machined
-
the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
WARNING! Danger of burns -
when changing tools
-
when setting the device down
Chips and splinters must not be removed while the machine is running.
When working in walls ceiling, or floor, take care to avoid electric cables and
gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped workpieces can cause
severe injury and damage.
Do not use cracked or distorted saw blades.
Plunge cuts without pre-drilling a hole are possible with soft materials
(wood, light building materials for walls). Harder materials (metals) must
first be drilled with a hole corresponding to the size of the saw blade.
Remove the battery pack before starting any work on the machine.
Do not dispose of used battery packs in the household refuse or by burning
them. Milwaukee Distributors offer to retrieve old batteries to protect our
environment.
Do not store the battery pack together with metal objects (short circuit
risk).
No metal parts must be allowed to enter the battery section of the charger
(short circuit risk).
Use only System 18 V chargers for charging System 18 V battery packs. Do not
use battery packs from other systems.
Never break open battery packs and chargers and store only in dry rooms. Keep
dry at all times.
Battery acid may leak from damaged batteries under extreme load or extreme
temperatures. In case of contact with battery acid wash it off immediately with
soap and water. In case of eye contact rinse thoroughly for at least 10
minutes and immediately seek medical attention.
Warning! To reduce the risk of fi re, personal injury, and product damage
due to a short circuit, never immerse your tool, battery pack or charger in
fluid or allow a fluid to fl ow inside them. Corrosive or conductive fluids, such
as seawater, certain industrial chemicals, and bleach or bleach containing
products, etc., can cause a short circuit.
SPECIFIED CONDITIONS OF USE
This jig saw can cut wood, plastic and metal; it can cut straight lines,
bevels, curves, and internal cut-outs.
Do not use this product in any other way as stated for normal use.
EC DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility that the product
described under “Technical Data” fulfi lls all the relevant regulations and the
directives 2011/65/EU (RoHS), 2014/30/EU, 2006/42/EC, and the following
harmonized standards have been used:
EN 62841-1:2015
EN 62841-2-11:2016+A1:2020
EN 55014-1:2017+A11:2020
EN 55014-2:2015
EN IEC 63000:2018
Winnenden, 2021-08-16
Alexander Krug
Managing Director
Authorized to compile the technical file
Techtronic Industries GmbH Max-Eyth-Straße 10 71364 Winnenden Germany
GB-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility that the product
described under “Technical Data” fulfi lls all the relevant provisions of the
following Regulations S.I. 2008/1597 (as amended), S.I. 2016/1091 (as
amended), S.I. 2012/3032 (as amended) and that the following designated
standards have been used:
BS EN 62841-1:2015
BS EN 62841-2-11:2016+A1:2020
BS EN 55014-1:2017+A11:2020
BS EN 55014-2:2015
BS EN IEC 63000:2018
Winnenden, 2021-08-16
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH Max-Eyth-Straße 10 71364 Winnenden Germany
BATTERIES
New battery packs reach full loading capacity after 4 – 5 chargings and
dischargings. Battery packs which have not been used for some time should be
recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of the battery
pack. Avoid extended exposure to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully charged, after
use.
To obtain the longest possible battery life remove the battery pack from the
charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C and away from
moisture
Store the battery packs in a 30% – 50% charged condition
Every six months of storage, charge the pack as normal.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all times.
Use only Milwaukee accessories and spare parts. Should components need to be
replaced which have not been described, please contact one of our Milwaukee
service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state the
Article No. as well as the machine type printed on the label and order the
drawing at your local service agents or directly at: Techtronic Industries
GmbH, Max-Eyth-Straße 10, 71364 Winnenden, Germany.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods Legislation
requirements.
Transportation of those batteries has to be done in accordance with local,
national and international provisions and regulations.
- The user can transport the batteries by road without further requirements.
- Commercial transport of Lithium-Ion batteries by third parties is subject to Dangerous Goods regulations.
Transport preparation and transport are exclusively to be carried out by appropriately trained persons and the process has to be accompanied by corresponding experts.
When transporting batteries:
- Ensure that battery contact terminals are protected and insulated to prevent short circuit.
- Ensure that battery pack is secured against movement within packaging.
- Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
SYMBOLS
| CAUTION! WARNING! DANGER!
---|---
| Remove the battery pack before starting any work on the machine.
| Please read the instructions carefully before starting the machine.
| Accessory – Not included in standard equipment, available as an accessory.
| Do not dispose of waste batteries, waste electrical and electronic
equipment as unsorted municipal waste. Waste batteries and waste electrical
and electronic equipment must be collected separately.
Waste batteries, waste accumulators and light sources have to be removed from
equipment.
Check with your local authority or retailer for recycling advice and
collection point.
According to local regulations retailers may have an obligation to take back
waste batteries and Waste electrical and electronic equipment free of charge.
Your contribution to re-use and recycling of waste batteries and waste
electrical and electronic equipment helps to reduce the demand of raw
materials.
Waste batteries, in particular containing lithium and waste Electrical and
electronic equipment contain valuable, recyclable materials, which can
adversely impact the environment and the human health, if not disposed of in
an environmentally compatible manner.
Delete personal data from waste equipment, if any.
n0| Stroke rate under no-load
V| Volts
| Direct Current
| European Conformity Mark
| British Confomity Mark
| Regulatory Compliance Mark (RCM). Product meets applicable regulatory
requirements.
| Ukraine Conformity Mark
| EurAsian Conformity Mark
Copyright 2022
Techtronic Industries GmbH
Max-Eyth-Str. 10
71364 Winnenden Germany
+49 (0) 7195-12-0
www.milwaukeetool.eu
Techtronic Industries (UK) Ltd Parkway
Marlow, SL7 1YL UK
(02.22)
4931 4700 24
Documents / Resources
|
milwaukee HD18 JSB Heavy Duty Body Grip
Jigsaw
[pdf] Instruction Manual
HD18 JSB-402C, HD18 JSB-0, HD18 JSB, Heavy Duty Body Grip Jigsaw, HD18 JSB
Heavy Duty Body Grip Jigsaw, Body Grip Jigsaw, Grip Jigsaw, Jigsaw
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>