DYNOJET PC6-18004 Power Commander 6 Installation Guide
- June 4, 2024
- Dynojet
Table of Contents
POWER COMMANDER 6
Installation Guide for PC6-18004
Model Coverage:
2008-2010 KTM RC8
2009-2010 KTM RC8R
PARTS LIST
1 POWER COMMANDER 6
1 INSTALLATION GUIDE
1 USB CABLE
2 DYNOJET DECALS
2 POWER COMMANDER DECALS
2 VELCRO STRIPS
1 ALCOHOL SWAB
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION.
THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION.
INPUT ACCESSORY GUIDE
OPTIONAL ACCESSORY INPUTS
Map| (Input 1 or 2) The PC6 has the ability to hold 2 different base maps. You
can switch on the fl y between these two base maps when you hook up a switch to
the MAP inputs. You can use any open/close type switch. The polarity of the
wires is not important.
---|---
Shifter| (Input 1 or 2) Used for clutch-less full-throttle upshifts. Insert
the wires from the Dynojet quick shifter into either
Input 1 or Input 2. The polarity of the wires is not important. Set to Input 2
by default.
Speed| If your application has a speed sensor then you can tap into the signal
side of the sensor and run a wire into this input. This will allow you to
calculate gear position in the Control Center Software. Once gear position is
set up you can alter your map based on gear position and setup gear-dependent
kill times when using a quick shifter.
Analog| This input is for a 0-5v signal such as engine temp, boost, etc. Once
this input is established you can alter your fuel curve based on this input in
the Power Core software.
Launch| You can connect a wire to either Input 1 or Input 2 and then the other
end to a switch. This switch when engaged (continuity) will only allow the RPM
to be raised to a certain limit (set in the software). When released, you will
have full RPM.
WIRE CONNECTIONS
To input wires into the PC6 first remove the rubber plug on the backside of the
unit and loosen the screw for the corresponding input. Using a 22-24 gauge
wire, strip about 10mm from its end. Push the wire into the hole of the PC6
until it stops and then tightens the screw. Make sure to reinstall the rubber
plug.
NOTE: If you tin the wires with solder it will make inserting them
easier.
INSTALLING THE POWER COMMANDER 6
-
Remove the seat and both side fairings.
-
Remove the fuel tank.
-
Lay the PC6 next to the battery and route the PC6 harness along the frame on the right side up towards the front of the engine.
-
Locate the Rear Ignition Coil and unplug the stock wiring harness from the coil.
-
Plug the pair of PC6 connectors with the BLUE-colored wires in-line with the Rear Ignition Coil and the stock wiring harness.
-
Locate the sub-connector from the throttle bodies on the right side of the motorcycle. Unplug this connector.
This is a GREY 16-pin connector pair located between the frame and the air box near the tip over the sensor.
-
Route the PC6 harness to the inside of the frame (which may require you to move the MAP sensor.)
-
Plug the pair of 16-pin PC6 wiring harness connectors in-line with the stock wiring harness.
-
Locate the Front Ignition Coil and unplug the stock wiring harness from the coil.
-
Plug the pair of PC6 connectors the GREEN-colored wires in-line with the Front Ignition Coil and the stock wiring harness.
-
Locate the stock Crank Position Sensor connectors on the left side of the motorcycle. Unplug this connection.
This is a BLUE 2-pin connector pair. On one side of the connector, it has a RED wire and a GREEN wire.
-
Route the pair of WHITE 2-pin PC6 connectors over to the left side of the motorcycle and plug them in line with the stock Crank Position Sensor connectors.
-
Feed the pair of connectors back over to the right side of the motorcycle.
-
Attach the PC6 ground wire with the small ring lug to the stock common ground location on the right side of the frame.
-
Using the supplied Velcro, install the PC6 behind the battery.
Clean both surfaces with the supplied alcohol swab prior to applying the Velcro adhesive. -
Reinstall the fuel tank, the bodywork, and the seat.
Download the latest map files from our website at dynojet.com/tunes.
PUSH THE LIMIT
2191 MENDENHALL DRIVE, NORTH LAS VEGAS, NV 89081
800-992-4993
DYNOJET.COM
© 2008-2022 DYNOJET RESEARCH
ALL RIGHTS RESERVED
PC6-18004
2008-2010 KTM RC8•2099-2010 KTM RC8R
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>