FORTIN 2007 Jeep Wrangler Regular Key Remote Starters and Alarm Systems Installation Guide

ADDENDUM – SUGGESTED WIRING CONFIGURATION
REGULAR & THAR-CHR5 INSTALLATION

2007 Jeep Wrangler Regular Key Remote Starters and Alarm Systems

VEHICLE………… YEARS
JEEP Wrangler 2007

Vehicle functions supported in this diagram (functional if equipped)

| Immobilizer bypass
---|---
| Lock
| Unlock
| Arm
| Disarm
| Parking Lights
| Tachometer
| Door Status
| Trunk Status
| Hand-Brake Status
| Foot-Brake Status
| OEM Remote monitoring

FIRMWARE VERSION|
---|---

To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately. Program bypass option
IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:

Program bypass option (If equiped with OEM alarm):

WIRE TO WIRE DIAGRAM

THARNESS DIAGRAM

| Parts required (Not included)| PAGE
---|---|---
THARNESS THAR-CHR5
WITH DATA-LINK| 1x THAR-CHR5
1x 7.5 Amp. fuse (see note page 2)| Page 3
THARNESS THAR-CHR5
WITHOUT DATA-LINK| 1x THAR-CHR5
1x 7.5 Amp. fuse (see note page 2)| Page 4

MANDATORY INSTALL

• HOOD PIN CONTACT HOOD STATUS : THE HOOD PIN SWITCH MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF. Notice: the installation of safety elements are mandatory. The hood pin is an essential security element and must be installed.
  THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.
  NOTES 12V BATTERY

ATTENTION THE T-HARNESS CURRENT IS LIMITED AT 10 AMP MAXIMUM.
If a parking lights (+) wire is use : that require more than 10Amp. Connect the remote-starter’s power directly to the vehicles battery with the appropriate fuse.
Some remote starters can not be powered through Data-Link. In these cases connect the remote starter’s fused 12V power wire directly to the T-Harness.

WIRING CONNECTION WITH DATA-LINK

THAR-CHR5  WIRING CONNECTION WITH DATA-LINK

THAR-CHR5 | WIRING CONNECTION WITHOUT DATA-LINK

PROGRAMMING PROCEDURE

| Press and hold the programming button:
Connect the 4-PIN Data-link harness (Black connector).
The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate.
---|---
| Release the programming button when the LED is BLUE.
If the LED is not solid BLUE disconnect the 4-Pin connector (Data-Link) and go back to step 1.
| Insert the required remaining connectors.
| Turn the key to the Ignition ON/RUN position.
“The BLUE LED will fash rapidly.
| Turn the key to the OFF position.
The BLUE LED will flash rapidly.
| Press the LOCK button on the vehicles OEM remote.
Press and release the programming button on the module once.
| The BLUE LED will tum off.

The mode is now programmed.
Use the remote of the remote starter or security system to test all of the supported features to ensure proper programming.

REMOTE STARTER FUNCTIONALITY

| All doors must be closed.
---|---
| Remote start the vehicle.
| Unlock the doors with the remote-starter remote or the OEM remote.
| Insert and Turn the key to the  Ignition ON/RUN position.
| Press the brake pedal.
| The vehicle can now be put in to gear and driven.

Notice: Updated Firmware and Installation Guides
Updated firmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest fi rmware and download the latest installation guide(s) prior to the installation of this product.
WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualifi ed technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.

TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797
ADDENDUM GUIDE
www.fortinbypass.com
WEB UPDATE

Documents / Resources

| FORTIN 2007 Jeep Wrangler Regular Key Remote Starters and Alarm Systems [pdf] Installation Guide
2007 Jeep Wrangler Regular Key Remote Starters and Alarm Systems, 2007 Jeep, Wrangler Regular Key Remote Starters and Alarm Systems, Key Remote Starters and Alarm Systems, Remote Starters and Alarm Systems, Starters and Alarm Systems, Alarm Systems, Systems
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>