FORTIN 2005 Dodge Durango Regular Key Remote Starters and Alarm Systems Installation Guide
- June 13, 2024
- FORTIN
Table of Contents
REV.: 20211117
Guide # 78041
STAND ALONE INSTALLATION
ADDENDUM – SUGGESTED WIRING CONFIGURATION
2005 Dodge Durango Regular Key Remote Starters and Alarm Systems
VEHICLE
YEARS
Vehicle functions supported in this diagram (functional if equipped)
Immobilizer bypass
- T-Harness available (sold separately)
- Lock
- Unlock
- Arm
- Disarm
- Trunk (open)
- RAP Disable
- Tachometer
- Door Status
- Trunk Status
- Hand-Brake Status
- Foot-Brake Status
DODGE
| Dakota | 2005 | • | • | • | • | • | • | • |
|---|---|---|---|---|---|---|---|---|
| Durango | 2004-2006 | • | • | • | • | • | • | • |
| BYPASS FIRMWARE VERSION | ||||||||
| VERSION LOGICIELLE CONTOURNEMENT | To add the firmware version and the options, |
use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.
---|---|---
| Program bypass option (If equipped with OEM alarm):| UNIT OPTION|
DESCRIPTION
---|---|---|---
D2| Unlock before / Lock after (Disarm OEM alarm)
IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:| | Hood trigger
(Output Status).
Parts required (Not included)
1X Relay
1X Resistor
MANDATORY INSTALL
- HOOD PIN CONTACT| | HOOD STATUS : THE HOOD PIN SWITCH (INCLUDED)
MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.
---|---|---
SECURITY STICKER
WARNING
Included
Notice: the installation of safety elements are mandatory. The hood pin
and the sticker are essential security elements and must be installed.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION
CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.
WIRING CONNECTION
KEY BYPASS PROGRAMMING PROCEDURE
| Press and hold the programming button:
Connect the 6-PIN Main harness (White connector).
The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate.
---|---
| Release the programming button when the LED is BLUE.
If the LED is not solid BLUE disconnect the 6-Pin connector (Main-Harness) and
go back to step 1.
| Insert the required remaining connectors.
| Turn the key to the Ignition ON/RUN position.
The BLUE LED will flash rapidly.
| Turn the key to the OFF position.
The BLUE LED will flash rapidly.
| Press the LOCK button on the
vehicles OEM remote.
| Press and release the programming
button on the once.
Notice: Updated Firmware and Installation Guides
Updated firmware and installation guides are posted on our web site on a
regular basis. We recommend that you update this module to the latest firmware
and download the latest installation guide(s) prior to the installation of
this product.
WARNING
The information on this sheet is provided on an (as is) basis with no
representation or warranty of accuracy whatsoever.
It is the sole responsibility of the installer to check and verify any circuit
before connecting to it. Only a computer safe logic probe or digital
multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no
liability or responsibility whatsoever pertaining to the accuracy or currency
of the information supplied. The installation in every case is the sole
responsibility of the installer performing the work and FORTIN ELECTRONIC
SYSTEMS assumes no liability or responsibility whatsoever resulting from any
type of installation, whether performed properly, improperly or any other way.
Neither the manufacturer or distributor of this module is responsible of
damages of any kind indirectly or directly caused by this module, except for
the replacement of this module in case of manufacturing defects. This module
must be installed by qualified technician. The information supplied is a guide
only. This instruction guide may change without notice. Visit
www.fortinbypass.com to get the latest version.
This guide may change without notice. See
www.fortin.ca for latest version.
TECH SUPPORT
Tél: 514-255-HELP (4357) 1-877-336-7797
Made in Canada
ADDENDUM GUIDE
www.fortinbypass.com
WEB UPDATE