FORTIN 98461 2019 Jeep Compass Push Button Remote Starters And Alarm Systems Installation Guide

FORTIN 98461 2019 Jeep Compass Push Button Remote Starters And Alarm

Systems

Vehicle Functions

THARNESS DIAGRAM

• THARNESS THAR-CHR7 /1x THAR-CHR7 /1x THAR-CHR7
• THARNESS THAR-CHR6 /1x THAR-CHR6 /1x THAR-CHR6

MANDATORY INSTALL

HOOD STATUS

•  THE HOOD PIN SWITCH (INCLUDED) MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.

A11: OFF

SECURITY STICKER

• Included

Notice: the installation of safety elements are mandatory. The hood pinand the sticker are essential security elements and must be installed.

THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.

NOTES

DESCRIPTION

WIRING CONNECTION

THAR-CHR7/ WIRING CONNECTION

THAR-CHR6 /WIRING CONNECTION

DCRYPTOR PROGRAMMING PROCEDURE

Parts required (not included)

• FLASH LINK UPDATER,

• FLASH LINK MANAGER SOFTWARE | PROGRAMME

• Microsoft Windows Computer with Internet connection Ordinateur Microsoft Windows avec connection Internet

• FLASH LINK MOBILE

• FLASH LINK MOBILE APP

• Smartphone Android or iOS with Internet connection (Internet provider charges may apply)

BEFORE PROGRAMMING SET THE UNIT OPTIONS AND SAVE.

• Press and hold Connect the programming button: the 6-PIN Main harness (White connector).
  • The LEDs will alternate between BLUE, RED, YELLOW & BLUE/RED flashes.
• Release the programming button when the LED is BLUE.
  • If the BLUE LED is not ON solid disconnect the 6-Pin Main connector and go back to step 1.
• Insert the required remaining connectors.
• Press the Push-to-Start button once to turn ON the ignition.
• Press and release the programming button once (1x).
  • Wait: The BLUE LED will flash rapidly.
• Press the Push-to-Start button once to turn off the ignition.
  • The BLUE LED will turn OFF.
  • The RED LED will turn ON.

KEY BYPASS PROGRAMMING PROCEDURE 2/2

• Press the Push-to-Start button once to turn ON the ignition.
  • The YELLOW LED will turn ON.
  • The RED LED will turn OFF.
  • The RED LED will turn ON.
• Repeat this process approximately 10 times.
• Press the Push-to-Start button once to turn ON the ignition.
• Press the Push-to-Start button once to turn off the ignition.

UNTIL

AT IGNITION OFF:

• The RED and the YELLOW LED’s alternate.
• Disconnect all connectors and after the 6-Pin (Main-Harness) or the 4-Pin Data-link connector.
• Microsoft Windows Computer with Internet connection*
• Smartphone* (Internet provider charges may apply)
  • Use the tool:
  • FLASH LINK UPDATER or FLASH LINK MOBILE to visit the DCryptor menu.
  • Parts required (not included)

AFTER DCRYPTOR PROGRAMMING COMPLETED

• Go back to the vehicle and reconnect the 6-Pin (Main- Harness) or the 4-pins (Data-Link) connector and after all the remaining connector.
• The module is now programmed.

REMOTE STARTER

• Test the remote starter. Remote start the vehicle.

REMOTE STARTER PROGRAMMING PROCEDURE

• REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE STARTER PROGRAMMING.

REMOTE STARTER FUNCTIONALITY

• All doors must be closed.
• Remote start the vehicle.

Unlock the doors with either:

• The OEM remote

• The remote-starter remote

• Or the proximity remote

• Enter the vehicle with the Intelligent Key.

• The vehicle can now be put in to gear and driven.

Warning: If the vehicle is not unlocked with one of these conditions the remote-starter will shut down as soon as any door is opened.

Notice: Updated Firmware and Installation Guides

Updated firmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest firmware and download the latest installation guide(s) prior to the installation of this product.

Module label

WARNING

The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way.

Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualified technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.

CONTACT

TECH SUPPORT

• Tél: 514-255-HELP (4357)
  • 1-877-336-7797
• WEB UPDATE:www.fortinbypass.com

This guide may change without notice. See www.fortin.ca for latest version.

Copyright © 2006-2018, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT PENDING

References

• Remote Car Starters, Car Alarms, Immobilizer Bypass and Connected Vehicle Solutions | Fortin Electronic Systems

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>