FORTIN 82761 2009 Toyota Tundra Regular Key Remote Starters And Alarm Systems Installation Guide

: June 13, 2024
: FORTIN

Table of Contents

FORTIN 82761 2009 Toyota Tundra Regular Key Remote Starters And Alarm
DESCRIPTION
WIRING CONNECTION
KEY BYPASS PROGRAMMING PROCEDURE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

FORTIN 82761 2009 Toyota Tundra Regular Key Remote Starters And Alarm

Systems

REGULAR INSTALLATION

ADDENDUM – SUGGESTED WIRING CONFIGURATION

HARDWARE VERSION

7 MINIMUM
BYPASS FIRMWARE VERSIONVERSION LOGICIELLE CONTOURNEMENT
To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.

Program bypass option:

IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:

UNIT OPTION OPTION UNITE/DESCRIPTION

C1: OEM Remote status (Lock/Unlock) monitoring

A11 OFF/NON

Hood trigger (Output Status).

Program remote starter option:

FUNCTION FONCTION/MODE/DESCRIPTION

2/ 4/(+) Start 2 (E1)
2/ 4 /(+) Ignition 2 (E2)

MANDATORY INSTALL

HOOD PIN

HOOD STATUS : THE HOOD PIN SWITCH (INCLUDED) MUST BE INSTALLED IF THE VEHICLE CAN BEREMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.

Notice: the installation of safety elements are mandatory. The hood pin and the sticker are essential security elements and must be installed.

THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.

DESCRIPTION

WIRING CONNECTION

KEY BYPASS PROGRAMMING PROCEDURE

Press and hold the programming button.
Insert the connectors: 20 pin (White),6 pin (Red), 5 pin (White), 2 pin (White). (If required)
Insert the 6-Pin Main connector
The LEDs will alternate between BLUE, RED, YELLOW & BLUE/RED flashes.
Release the programming qbutton when the LED is RED
If the LED is not solid RED disconnect the 6 Pin connector (Main-Harness) and go back to step 1.
Insert one functional key into the ignition barrel.
DO NOT turn ON the key.
The RED LED will flash rapidly 10x times. Key bypass programmed
Turn the Ignition to the ON/RUN position.
Wait The BLUE LED will flash rapidly. CAN-Bus programmed
The BLUE LED will turn off.

The module is now programmed.

Use the remote of the remote starter or security system to test all of the supported features to ensure proper programming.

REMOTE STARTER PROGRAMMING PROCEDURE

REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE STARTER PROGRAMMING ****

Notice: Updated Firmware and Installation Guides Updated fi rmware and installation guides are posted on our web site on a regularbasis. We recommend that you update this module to the latest fi rmware and download the latest installation guide(s) prior to the installation of this product.

WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safelogic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualifi ed technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.

TECH SUPPORT