CLAS OM 8034 Universal Bearing Removal Set User Manual
- June 13, 2024
- CLAS
Table of Contents
OM 8034
UNIVERSEL
UNIVERSAL BEARING REMOVAL SET
OM 8034 Universal Bearing Removal Set
WARNING
Before returning this product for any reason (installation problem,
instructions for use, breakdown, manufacturing problem…), please contact us.
Contact:
You can reach us by mail sav@clas.com or by phone
+33(0)4 79 72 69 18 or go directly to our website clas.com
If you have changed your mind regarding your purchase, please return this
product before you attempt to install it.
COMPONENTS
1| PRESS PLATE Ø61,5 mm – ØINS.1 29,5 mm – ØINS.2 33,5mm|
---|---|---
2| PRESS PLATE Ø64,5 mm – ØINS.1 33,5 mm – ØINS.2 34,5mm|
3| PRESS PLATE Ø67,5 mm – ØINS.1 33,5 mm – ØINS.2 37,5mm|
4| PIPRESS PLATE Ø71,5 mm – ØINS.1 34,5 mm – ØINS.2 37,5mm|
5| PRESS PLATE Ø73,5 mm – ØINS.1 36,5 mm – ØINS.2 38,5mm|
6| PRESS PLATE Ø74,5 mm – ØINS.1 38,5 mm – ØINS.2 40,5mm|
7| PRESS PLATE Ø75,5 mm – ØINS.1 39,5 mm – ØINS.2 41,5mm|
8| PRESS PLATE Ø79,5 mm – ØINS.1 39,5 mm – ØINS.2 42,5mm|
9| PRESS PLATE Ø81,5 mm – ØINS.1 41,5 mm – ØINS.2 43,5mm|
10| PRESS PLATE Ø83,5 mm – ØINS.1 41,5 mm – ØINS.2 44,5mm|
11| PRESSURE SLEEVE INSIDE Ø72, WITH WINDOW|
12| PRESSURE SLEEVE INSIDE Ø80, WITH WINDOW|
13| PRESSURE SLEEVE INSIDE Ø88, WITH WINDOW|
14| STEPPED PLATE Ø72 – 80 – 88 mm WITH THRUST BEARING ADMISSION|
15| WASHER M20 X 3 mm|
16| AXE DE POUSSEE|
17| SPINDLE M20 X 1.5 L = 300 mm|
18| PRESSURE NUT M20 X 1.5 L = 50 mm|
19| PRESSURE BEARING|
APLICATIONS
| VW | Honda |
|---|---|
| Audi | Mazda |
| Opel | Mitsubishi |
| Mercedes Benz | Nissan |
| Peugeot | Toyota |
| Citroën | Austin-Maestro |
| Renault | BMW |
| Ford |
INTRODUCTION
Use accident-proof gloves, accident-proof shoes, hard hat and safety glasses..
Improper use:
– The product should be used only for the purpose intended in this literature.
Any other use is to be considered improper.
– The manufacturer assumes no responsibility for any damage resulting from
improper or unreasonable use of the equipment.
– Improper use voids the warranty.
Take good care of the tools:
– Always keep tools clean.
– Store tools in their original packaging.
WARNINGS
The operation of the kit is reserved for expert personne.
INSTRUCTIONS
| Plate | Ø external 5(mm) | Ø inner 1 (mm) | Ø inner 2 (mm) |
|---|---|---|---|
| 1 | 61.5 | 29.5 | 33.5 |
| 2 | 64.5 | 33.5 | 34.5 |
| 3 | 67.5 | 33.5 | 37.5 |
| 4 | 71.5 | 34.5 | 37.5 |
| 5 | 73.5 | 36.5 | 38.5 |
| 6 | 74.5 | 38.5 | 40.5 |
| 7 | 75.5 | 39.5 | 41.5 |
| 8 | 79.5 | 39.5 | 42.5 |
| 9 | 81.5 | 41.5 | 43.5 |
| 10 | 83.5 | 41.5 | 44.5 |
Manual application with M20 screw (inclusded in the tool sel) or with 17T
hydraulic cylinder – stroke 43mm – ref. OM 8037 (cylinder not included in the
tool set – long screw is require).
WHEEL BEARING REMOVAL
Identify all the required pieces and assemble the tools as follows:
- Measure the inner and outer diameter of the bearing
- Identify the appropriate bearing pressure ring.
- Diam. of pressure ring A = bearing outer diameter
- Diam. of centring bearing B = bearing inner diameter
- Select the appropriate support (C) according to the bearing’s outer diameter (diameter of support D> wheel bearing diameter).
- During removal, the bearing must slide inside the support (D).
- Select the appropriate centring device for supports ( F).
- Assemble the screw (E) the nut with the bearing (I) and the nut ( H) (fig. 2).
- Begin to remove as shown in fig. 3. You can monitor the progress of operations through the slot on the supports. Figure 4 shows the completion of the removal procedure.
WHEEL BEARING ASSEMBLY
Identify all the required pieces and assemble the tools as follows:
- Measure the inner and outer diameter of the bearing
- Identify the appropriate bearing pressure ring A centring ring ( B).
- Diam. of pressure ring A = bearing outer diameter
- Diam. of centring bearing B = bearing inner diameter
- Select the appropriate support (C) according to the bearing’s outer diameter (diameter of support D> wheel bearing diameter).
- Select the centring device for supports (F).
- Assemble the screw (E) the nut with the bearing (I) and the nut (H) (fig. 2).
- Insert the new bearing as shown in figure 6.
Always check that the bearing is in the correct position during insertion: it
is essential that the bearing be centered when inserted WHEEL HUB ASSEMBLY
Identify all the required pieces and assemble the tools as follows:
-
Identify the appropriate pressure ring A.
WARNING: the diameter of the selected pressure ring must be greater than the bearing’s seat. -
Mount the selected pressure ring A on the adapter (C)
-
Select the appropriate support (C) and its device (F)
-
Assemble the tools as shown in Figure 7 and fit the hub into the bearing.
Always check that the hub is in the correct position during insertion: it is essential that the hub be centered when inserted. CLAS disclaims any liability arising from misuse of its tools.
CLAS Equipements
ZA de la CROUZA
73800 CHIGNIN
FRANCE
Tél. +33 (0)4 79 72 62 22
Fax. +33 (0)4 79 72 52 86
If you need components or parts, please contact the reseller.
In case of problems, please contact your authorized technician.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>