saxby lighting 13759 Spegel Shaver Mirror Instruction Manual
- October 30, 2023
- saxby lighting
Table of Contents
Instruction manual
Spiegel Shaver Mirror
13759
13759 Spegel Shaver Mirror
Thank you for purchasing this light fitting. Please read the instructions
carefully before use to ensure safe and satisfactory operation of this
product. Please retain these instructions for future reference.
Warning
This is a Class 1 product and must be earthed.
Please read these instructions carefully before commencing any work.
This unit must be fitted by a competent and qualified electrician.
Check the pack and make sure you have all the parts listed.
Install in accordance with the IEE Wiring regulations and current Building
Regulations.
To prevent electrocution switch off at mains supply before installing or
maintaining this fitting. Ensure other persons cannot restore the electrical
supply without your knowledge. If you are in any doubt, please consult a
qualified electrician.
This light fitting should be connected to a fused circuit.
If replacing an existing fitting, make a careful note of the connections.
This product is suitable for indoor use only, on normal flammable surfaces.
This product contains non-replaceable parts and cannot be serviced. If damage
occurs the part should be scrapped.
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your local authority or
retailer for recycling advice.
Layout
Plan the desired layout of these fittings carefully, ensuring the cables will
reach the distance between the Junction box and the light fitting.
Avoid locating any cables in positions that would cause a hazard. Position
cables and junction boxes (not supplied) away from areas where they may be at
risk from being cut, trapped or damaged.
The mains supply cable must have a minimum cross sectional area of 1.0mm²
Cables in wall must be protected using suitable conduit or plastic trucking.
The cable entry hole is on the left hand-side of the product and is accessed
removing the mirror panel.
This product has special protection against the ingress of moisture.
This product is fitted with a no touch infrared switch, helping to keep the
mirror clear of fingerprints. Caution: To avoid interference, the sensor must
be placed a minimum of 200mm away form any surface of object.
This product is suitable for use bathroom zone 2 and outside zones of a
bathroom only. Please see diagram on the right.
If this unit is being fitted in a room containing a bath or shower, a 30mA RCD
must be used – in accordance with IEE regulations.
Installation
Existing fittings must be completely removed before installation of a new
product. Before removing the existing fitting, carefully note the position of
each set of wires.
Note that the switch is turned off before installation.
This product is suitable for installation on surfaces with normal flammability
e.g. wood, plasterboard and masonry. It is not suitable for use on highly
flammable surfaces (e.g. polystyrene, textiles).
If mounting, note the position of the “This Way Up” label on the back of the
product and ensure it is correctly oriented.
An assistant may be required to aid installation of this product.
- Remove the wall back from the product by removing the side fixing screws and rubber washers.
- Hold the wall back in place and mark the position of the holes. Ensure that the product is level.
- Ensure the wall is capable of holding the weight of the product. Take care to avoid damaging any concealed wiring and pipes. The correct fixings should be used for brick, cavity walls or plasterboard.
- Pierce grommet and pass the supply cable through the hole in the wall back.
- Fix the product into position. Take care not to trap the supply wire.
Wiring
Having correctly identified the wiring from your light fitting, Pull the wire
through the hole and connect to the connection block inside the product in the
following way:
Check that…
- You have correctly identified the wires.
- The connections are tight.
- No loose strands have been left out of the connection block.
- When completed, ensure that there are no bare or loose strands of wire exposed, and cover all exposed areas of the connection block with 2 layers of insulation tape.
Commissioning
- Refit the mirror onto the wall back. Ensure that the seals are correctly located before securing.
- Replace fuse or circuit breaker and switch on. Your light is now ready for use.
- This mirror is operated by a touch sensor. To turn the LED’s in the mirror on the sensor must be lightly touched. To turn off the LED’s touch the sensor again.
- The access the shaver socket, lift the grey flap up on the side. Slect either 240V or 110V depending on the model of shaver.
Shaver Socket Instructions
- The shaver socket is powered by a 20W isolating transformer and is only intensified for use with electric shavers, electric toothbrush chargers and similar products.
- Any appliance connected to the socket must not exceed the 20W power output as this could cause damage and overheating to occur.
- Always check your appliance instructions to ensure the power requirements are less than 20W.
Technical Data
Supply Voltage: 220-240 V~, 50 Hz
Shaver Socket: 115V – 240V dual socketl
Bulb Type: 10.8W LED module (SMD), 6500K This product contains a light
source of energy efficiency class E.
| Replaceable (LED only) light source by a professional
---|---
| Replaceable control gear by a professional
| Conformity with all relevant UKCA Directive requirements.
---|---
| Conformity with all relevant EC Directive requirements.
| This product is Class 1, must be connected to earth.
****| Waste electrical products should not be disposed of with household
waste. Please recycle where facilities exist. Check with your Local Authority
or local store for recycling advice.
| This product is not suitable for dimming.
| This product is rated at IP44.
Care and Safety
We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive
cleaners as these could damage the finish.
Mirror-Use a damp cloth or a propriety glass cleaner. Do not use abrasive
materials as these will damage the finish.
Live Voltages may be present in this unit even when turned of or when
completely disconnected. For your safety, always switch off the power supply
before changing lightbulbs, or cleaning.
| The mirror must be replaced immediately should it become cracked or damaged.
This fitting must not be used without the mirror in place.
---|---
For further information, please visit https://www.lighting-info.co.uk/31470
V3 01/04/2022
UK Manufacturer: BH17 7BY
EU Manufacturer: Brilliant AG,
Brilliantstrasse 1, D-27442 Gnarrenburg
www.saxbylighting.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>