FORTIN 20211117 Kia Sorento 2013 Standard-Key Remote Starters and Alarm Systems Installation Guide

FORTIN 20211117 Kia Sorento 2013 Standard-Key Remote Starters and Alarm

Systems

Product Information

• The product is an immobilizer bypass T-Harness designed for use with Kia Sorento vehicles with automatic transmission from 2010 to 2013. It allows for the bypassing of the immobilizer system and provides various functions such as lock/unlock, arm/disarm, hatch (open), RAP disable, tachometer, door status, trunk status, hood status, and hand-brake status.
• The product requires a minimum firmware version of 76.[60] for proper functionality. The firmware version and options can be added using the FLASH LINK UPDATER or FLASH LINK MOBILE tool, which are sold separately.
• If the vehicle is not equipped with a functional hood pin, the unit option A11 should be set to OFF. Additionally, if the vehicle can be remote started with the hood open, a hood pin switch (included) must be installed and the function A11 should be set to OFF.
• This product must be installed by a qualified technician to avoid permanent damage to the vehicle.

Product Usage Instructions

1. Ensure that the vehicle is a Kia Sorento with automatic transmission from 2010 to 2013.
2. Check the firmware version of the product and update it if necessary using the FLASH LINK UPDATER or FLASH LINK MOBILE tool.
3. If the vehicle does not have a functional hood pin, set the unit option A11 to OFF.
4. If the vehicle can be remote started with the hood open, install the included hood pin switch and set the function A11 to OFF.
5. Connect the product according to the provided wiring diagram.
6. Ensure that the product is securely installed by a qualified technician.
7. Test the functionality of the product by using the lock, unlock, arm, disarm, hatch open, RAP disable, tachometer, door status, trunk status, hood status, and hand-brake status functions.

Vehicle functions supported in this diagram

BYPASS FIRMWARE VERSION VERSION LOGICIELLE CONTOURNEMENT
76.[60] MINIMUM
To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately

Program bypass option IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:

A11

|

OFF NON

| Hood trigger (Output Status).

Contact de capot (état de sortie).

Program bypass option (If equiped with OEM alarm):

Déverrouille avant / Verrouille après (Désarme l’alarme d’origine)

Program remote starter option

(+) Accessoire 2 (E1)

MANDATORY INSTALL

HOOD PIN

HOOD STATUS : THE HOOD PIN SWITCH (INCLUDED) MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OF

A11 OFF NON
SECURITY STICKER
Notice: the installation of safety elements are mandatory. The hood pin and the sticker are essential security elements and must be installed.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE

DESCRIPTION

AUTOMATIC TRANSMISSION WIRING CONNECTION

KEY BYPASS PROGRAMMING PROCEDURE

1. Press and hold the programming button: Insert the 6-Pin Main connector

   • The BLUE, YELLOW, RED and BLUE & RED LEDs will alternatively illuminate

2. Release the programming button when the YELLOW LED is ON.

   • If the YELLOW LED is not ON solid, disconnect the 6-Pin Main connector and go back to step 1.

3. Insert the required remaining connectors.

4. Turn the key to the Ignition ON/RUN position.

   • The BLUE LED will flash rapidly ten (x10) times. CAN Network programmed.
     Wait
     When the RED and the YELLOW LED will turn ON:
     Turn the key to the OFF position.
     

5. Turn the key to the Ignition ON/RUN position

6. The RED, the BLUE and the YELLOW LEDs are ON: programming process started.

7. The LEDs slowly alternate between the RED, BLUE and YELLOW LED’s: processing…

8. When the YELLOW LED begins to flash rapidly: The key bypass is programmed.
   This process may take up to 5 minutes

9. Turn the key to the OFF position.

The module is now programmed
Use the remote of the remote starter or security system to test all of the supported features to ensure proper programming.

VEHICULE WITHOUT PATS DATA WIRE

1. Press and hold the programming button: Insert the 6-Pin Main connector
   • The LEDs will alternate between BLUE, RED, YELLOW & BLUE/RED flashes.
2. Release the programming button when the BLUE LED is ON.
   • If the BLUE LED is not ON solid disconnect the 6-Pin Main connector and go back to step 1.
3. Insert the required remaining connectors
4. Turn the Ignition to the ON/RUN position.
   • The BLUE LED will flash rapidly.
5. Turn the Ignition to the OFF position.
   • The BLUE LED will turn off.

The module is now programmed

REMOTE STARTER PROGRAMMING PROCEDURE

REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE STARTER PROGRAMMING.

REMOTE STARTER FUNCTIONALITY

Notice: Updated Firmware and Installation Guides
Updated fi rmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest fi rmware and download the latest installation guide(s) prior to the installation of this product.

WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualifi ed technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version

TECH SUPPORT
Tél: 514-255-HELP (4357) 1-877-336-7797
www.fortinbypass.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>